Sony CDX-CA900 Installation/Connections page 3

4 A B
x
1
2
6 A
TOYOTA
4
max. size
5 × 8 mm
to dashboard/centre console
Bracket
Bracket
Existing parts supplied with your car
Precautions Mounting the unit in a Japanese
car (6)
•Choose the installation location carefully so that
the unit will not interfere with normal driving
You may not be able to install this unit in some
operations.
makes of Japanese cars. In such a case, consult
•Avoid installing the unit in areas subject to dust,
your Sony dealer.
dirt, excessive vibration, or high temperatures,
such as in direct sunlight or near heater ducts.
Note
•Use only the supplied mounting hardware for a
To prevent malfunction, install only with the supplied
safe and secure installation.
screws 4.
Mounting angle adjustment
Adjust the mounting angle to less than 60°.
Warning when installing in a car
without ACC (accessory) position
on the ignition key switch
How to detach and attach the
front panel (4) Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
Before installing the unit, detach the front
turning off the engine.
panel.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
4-A To detach
battery wear.
Before detaching the front panel, be sure to press
(OFF). Press (OPEN), then slide the front panel
to the right side, and pull out the left side.
4-B To attach RESET button
Place the hole in the front panel onto the
When the installation and connections are
spindle on the unit as illustrated, then push the
completed, be sure to press the RESET button
left side in.
with a ballpoint pen, etc., after removing the front
panel.
Mounting example (5)
Installation in the dashboard
Note (5- )
*
When installing this unit: Depending on car
type, the mounting angle may not allow the
front panel to open easily. In such a case,
remove the silver screw A shown below.
When screwing it on again, first lock the lever B.
Attaching the screw without doing so may cause
the unit to break.
5 1
1
B
NISSAN
4
max. size
5 × 8 mm
to dashboard/centre console
4
max. size Bracket
5 × 8 mm
Existing parts supplied with your car
5 Warm the mounting surface and the double-
Installing the rotary commander sided adhesive tape on the mounting holder
9 with a hair drier, etc., to a temperature
(7)
between 20 °C and 30 °C, and attach the
mounting holder 9 onto the mounting
Notes
surface by applying even pressure. Then
• Choose the mounting location carefully so that the
screw it down with the screw 8.
rotary commander will not interfere with operating
Attach a piece of heavy duty tape etc. on the
the car.
• Install the rotary commander on a flat surface with a other side of the mounting surface to cover the
circular area of approximate 55 mm diameter.
protruding tip of the screw so that they will not
• Do not install the rotary commander where it may
interfere with the electrical cables etc. inside
jeopardize the safety of the (front) passenger in
the steering wheel column.
anyway.
• When installing the rotary commander, be sure not
Note
to damage the electrical cables etc. on the other side
Choose the mounting location carefully. The
of the mounting surface.
adhesive is very strong and relocation may be
• Avoid installing the rotary commander where it may
difficult.
be subject to high temperatures, such as from direct
Tighten the screw firmly so that the screw head
sunlight or hot air from the heater etc.
does not protrude.
When installing the unit on the steering
6 After installing the steering wheel column
column cover
cover, attach the rotary commander to the
1 Choose the exact location for the rotary mounting holder until it locks into place as
commander to be mounted temporarily,
illustrated.
then press the buttons and rotate the
controls to make sure that your master unit
reacts well.
Cautions
You can change the direction of infrared rays • If the master unit or the rotary commander is
by turning the dial on the rotary commander. exposed to direct sunlight, sensitivity of the
infrared receptor or emitter may deteriorate and
the master unit may not work properly. If this
Caution
happens, rotate the dial to readjust the direction of
Be sure that the place where you install the rotary
infrared rays.
commander is within the range of the receptor on
• Be sure to attach the supplied strap q; when
the unit.
installing the rotary commander near the steering
wheel.
2 Clean the mounting surface.
• Be sure that the strap q; does not get caught on the
Dirt or oil impair the adhesive strength of the
car controls (gear, shifter, etc.).
double-sided adhesive tape preattached to the
• Be sure to tighten the stopper of the strap q; after
mounting holder 9.
hanging the strap q; on the indicator switch, etc.
Tip
3 Mark the position for the supplied screw.
There are two holes for the strap q;. You can use
Use the screw hole on the mounting holder 9
whichever hole you prefer.
to mark the position.
Note
Note
If you are mounting the rotary commander to the
Make sure the orientation of the markings on both
steering wheel column, make sure that the
the mounting holder and the rotary commander is
protruding tip of the screw on the inner surface of
the same, and then attach.
the column do not in anyway hinder or interfere with
the movement of the rotating shaft, operative parts
4 Remove the steering wheel column cover,
of the switches or the electrical cables etc. inside the
and drill 2 mm diameter hole where you
column.
have marked.
2 3
4
Bend these claws outward
for a tight fit, if necessary.
5
Mounting example
7
4
4
max. size
5 × 8 mm
Bracket
•
•
•
4
(OFF)
(OPEN)
4
5
5
*
A
4
Dashboard
1
6
4
5
5 4
Releasing the rotary commander
1
(PUSH)
Infrared rays dial
1
1
2
5
Heavy duty tape etc.
9
8
6
•
•
•
•
4
•
4
(OFF)
(OFF)
B
*
Fire wall
2
A
B
2 3
Markings
9
Mark
6
the other hole
q;
q;
7 •
•
q;
•
q;
• q;
q;
q;
9
9
9
°C °C
9
8