Sony TRINITRON KV-27V40 Service Manual page 14

KV-27S40 / 27S45 / 27S65 / 29SL40 / 29SL40A / 29SL40C/
29SL45 / 29SL65 / 29SL65C/ 29XL40M / 29XL40P / 29XT11A
Using your New TV (continued)
Watching two programs at
one time - PIP
The Picture-in-Picture (PIP) feature allows you
to view two channels simultaneously, one in
the full size "main" picture and one in a smaller
"window" picture. This means that two
separate tuners must be available to provide
the two signals.
Certain models (KV-27S45, 27V45 only) are
equipped with a single tuner. This simply means
that a VCR must be connected and turned on for
PIP to operate.
Tip z
To ensure a correct single tuner PIP connection
(KV-27S45, 27V45 only), make sure the following list
is complete before using PIP:
• A cable or antenna is connected to the VCR
• The VCR is connected to your TV
• The VCR is turned on
(for detailed connection information, see pages 5-7)
Note
• You must press TV (FUNCTION) before you
can control PIP with the yellow labeled buttons.
16
Use the Yellow Labeled Buttons for PIP Operations.
Press to change the TV channel in the window picture. (KV-27S65, 27V65 only)
TV/VTR
For models KV-27S45, 27V45, you must press VTR/DVD (FUNCTION), then use
+
the main CH +/- buttons to change channels. (see right)
CH
–
POSITION Press to move the location of the window picture (counterclockwise) around the
main picture.
Press to freeze the window picture. Great for copying down phone numbers,
FREEZE
addresses, recipes, etc.
Press FREEZE again to restore the previous screen(s).
Press to switch the audio and video of the main picture and the window picture.
SWAP
Each time you press SWAP, the picture and sound of the two will be swapped .
Any channels being received through the AUX jack cannot be displayed as a
window picture. (KV-27S65, 27V65 only)
REFER TO THE ILLUSTRATION OF
THE REMOTE CONTROL ON THE
INSIDE FRONT COVER OF THIS
MANUAL AS YOU REVIEW THIS
CHART
Use the Yellow Labeled Buttons for PIP Operations.
Press once to display the window picture (1/9 size).
PIP
Press again to reduce the size of the window picture (1/16 size).
Press a third time to remove the window picture.
Press repeatedly to step through available video inputs:
TV/VIDEO
TV, VIDEO 1, VIDEO 2, and VIDEO 3 (KV-27S45, 27S65, 27V45,
27V65 only)
If you have a single tuner, your PIP input source is the VCR.
AUDIO
Press to alternate sound between the main picture and the window
picture. A will appear for a few seconds to indicate which picture is
receiving sound.
—
14 —
The sound of the main Input-source mode
picture is received.
or TV channel for
the main picture
Main
Input-source mode
picture
or TV channel for
the window picture
Window
picture
Changing channels with a single
tuner PIP
• KV-27S45, 27V45 only
1
Press TV/VIDEO until you reach the TV
input.
2
Press PIP (the window picture appears).
To change the window picture:
1
Press VTR/DVD (FUNCTION).
2
Press the main CH +/– buttons to change
channels.
To change the main picture:
1
Press TV (FUNCTION).
2
Press the main CH +/– buttons to change
channels.
Note
• If you have the same program in both the
window and the main picture and cannot
change the channel in the window; press
TV/VIDEO until you reach the TV input in the
main picture.
17