Download Print this page

Craftsman 358.350802 Instruction Manual page 10

2.6 cu.in./42cc 2-cycle gasoline chain saw

Advertisement

Available languages

Available languages

Braking function
control
CAUTION:
The chain brake must be
checked several
times daily. The en-
gine must be running when performing
this procedure.
This is the only
instance when the saw should be
placed on the ground with the engine
running.
Place the saw on firm ground. Grip the
rear handle with your right hand and
the front handle with your left hand.
Apply full throttle by fully depressing
the throttle trigger. Activate the chain
brake by turning your left wrist against
the hand guard without releasing
your
grip around the front handle. The chain
should stop immediately.
Inertia activating
function
control
ZIL _____
__ _
4;SWARNING:
When performing
the
following
procedure,
the engine must
be turned off.
Grip the rear handle with your right
hand and the front handle with your left
hand.
Hold the chain saw approxi-
mately
14" (35 cm) above a stump or
other wooden
surface. Release your
grip on the front handle and use the
weight of the saw to let the tip of the
guide bar fall forward and contact the
stump.
When the tip of the bar hits the
stump, the brake should activate.
OPERATING
TIPS
• Check chain tension
before first use
and after 1 minute of operation.
See
CHAIN TENSION in the MAINTENANCE
section.
• Cut wood only. Do not cut metal,
plastics, masonry, non-wood
building
materials,
etc.
• Stop the saw if the chain strikes a
foreign object.
Inspect the saw and
repair parts as necessary.
• Keep the chain out of dirt and sand.
Even a small amount of dirt will
quickly
dull a chain and increase
the
possibility
of kickback.
• Practice cutting a few small logs using
the following steps. This will help you
get the "feeF of using your saw before
you begin a major sawing operation.
• Squeeze
the throttle trigger and a!-
low the engine to reach foil speed
before cutting.
• Begin cutting with the saw frame
against the log.
• Keep the engine at foil speed the
entire time you are cutting.
• Allow the chain to cut for you. Exert
only light downward
pressure.
• Release the throttle trigger as soon
as the cut is completed,
allowing
the engine to idle. If you run the
saw at full throttle without
a cutting
load, unnecessary
wear can occur
to the chain, bar and engine.
It is
recommended
that the engine
not be operated
for longer
than
30 seconds
at full throttle.
• To avoid losing control when cut is
complete,
do not put pressure on
saw at end of cut.
• Stop engine before setting saw down.
TREE FELLING
TECHNIQUES
d_!_WARNING:
Check for broken or
dead branches
which can fall while
cutting causing serious
injury. Do not
cut near buildings
or electrical
wires if
you do not know the direction
of tree
fall, nor cut at night since you will not
be able to see well, nor during bad
weather such as rain, snow, or strong
winds, etc. If the tree does make con-
tact with any utility line, the utility com-
pany should be notified immediately.
• Carefully
pIan your sawing operation
in advance.
• Clear the work area. You need a
clear area all around the tree so you
can have secure footing.
• The chain saw operator
should keep
on the uphill side of the terrain as the
tree is likely to roll or slide downhill
after it is felled.
• Study the natural conditions
that can
cause the tree to fall in a particular
direction.
These conditions
include:
• The wind direction
and speed.
• The lean of the tree. The lean of a
tree might not be apparent
due to
uneven or sloping terrain. Use a
plumb or level to determine
the di-
rection of tree lean.
• Weight and branches on one side.
• Surrounding
trees and obstacles.
• Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
operator.
• Make sure there is enough room for
the tree to fall. Maintain
a distance of
2-1/2 tree lengths from the nearest
person or other objects.
Engine
noise can drown out a warning
call.
• Remove dirt, stones,
loose bark,
nails, staples, and wire from the tree
where cuts are to be made.
10

Advertisement

loading