Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Emprex GPS Bluetooth Receiver IGO-08A
Summary of Contents for Emprex GPS Bluetooth Receiver IGO-08A
- Page 1 GPS Bluetooth Receiver IGO-08A User’s Guide Version 1.0...
- Page 2 FCC GUIDELINES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 3 IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
-
Page 4: Table Of Contents
Table of Content Introduction ...1 Features ...1 Package content...2 Hardware Description ...3 Technology Specification ...5 Operation ...7... -
Page 5: Introduction
Introduction IGO-08A is a GPS receiver with Bluetooth interface adopts advanced ATMEL ANTARIS 4 Super Sense GPS IC, and built-in active antenna for high sensitivity to tracking signal, there’s also an external MMCX aerial terminal for users adding higher MMCX antenna. GPS Heading will be correct in low speed and stop through built -in Digital compass. -
Page 6: Package Content
Please make sure of your package includes the following items, If any item is damaged or missing, please contact your dealer at once. Bluetooth GPS receiver IGO-08A x 1 Lithium rechargeable battery x 1 USB cable x 1 Slipperiless pad x 1... -
Page 7: Hardware Description
Hardware Description There are four LEDs to show different status: Bluetooth（Blue） Fast blink: Indicates this Bluethooth GPS is waiting for Slow blink: Indicates this Bluetooth GPS is connecting Power LED（Red） Lighten: Charging Darken: Charging complete GPS （Green） Lighten: GPS power on Darken: GPS power off pairing or master device’... -
Page 8: Power Switch
Circle LED (Red) Digital compass & battery capacity display Charge socket Battery bolt Switch 1 ( Long press: Digital calibration On/ Off Short press: Digital compass function On/Off Switch 2 ( Long press: PC connecting mode On/Off Short press: BT function On/OFF Power switch Long press: Power On/ Off Short press: Power capacity display on circle LED... -
Page 9: Technology Specification
Technology Specification Receiving and tracking 16 satellites at the same time Satellite receiving Receiving frequency: 1575.42MHz Receiving code: L1, C/A code Accuracy General positioning: 2.5m CEP (Precision) DGPS/SBAS: 2.0m CEP Acquisition Cold start: 34 sec (Average) Warm start: 33 sec (Average) Hot start: 1 sec (Min) Sensitivity: -158dBm (Super sense mode) - Page 10 Compass Digital compass (2 AXIS) Data logger 25806 records Power supply: DC 5.0V Power 77mA (Average) consumption Operating -10°C~ +60°C Temp. Storage Temp. -20°C~ +85°C Humidity 5%~95% Size: 64(L) x 41 (W) x 19 (H)mm Weight 54g (include battery) Battery: Nokia 6100 compatible (spec.
-
Page 11: Operation
Operation 1. How to use battery 1-1 Charging battery more than 8 hours Before first time using IGO-08A’s battery, user has to charge the battery more than 8 hours. Connect travel charger or car charger with this device DC5V charge socket. - Page 12 after positioning successfully. 3. How to active Bluetooth enabled device There are many Bluetooth enable devices like PDA or Bluetooth dangle on the market, which direct connect with IGO-08A. Each one may have different Bluetooth setup procedure. Please refer to their user manual for detail instruction.
- Page 13 Compass calibration. Long press Switch 1 ( Digital Compass function is on now. 2. Do not put magnetic object close to GPS receiver to avoid of Compass function inefficacy. 3. Set the GPS receiver horizontal during using Compass function.
-
Page 14: Data Logger
4. We recommend user to turn off Digital compass heading in magnetic field. (Short press Switch 1 ( 6. Data logger 1. GPS Receiver could save 25806 data by build-in flash memory. 2. When 25806 data is full, it will save from the beginning and original data will be covered. - Page 15 A1. Stop Data logger A2. Start Driving Mode A3. Start Hiking Mode Attention 1. Users could choose to start Data logger function or not. 2. Recording mode could divide into driving mode and hiking mode. 3. Driving mode is recorded by steady distance. Hiking mode is recorded by steady time.
- Page 16 7. IGO-08 Download software 7-1 Install the IGO Logger 7-1-1 Please insert the application disc. Select “iGO Logger” file and click Next to continue 7-1-2 Select “Myself” and click Next.
- Page 17 7-1-3 It’s ready to install, please click Next. 7-1-4 Please wait. 7-1-5 IGO Logger has installed successfully.
- Page 18 7-2 Install the USB Bridge Driver ( PL-2303) 7-3 Connect with USB cable Plug one end of the USB cable to the USB port on your computer. Connect the other end of the USB cable to the USB socket of IGO-08A. 7-2-1 Please insert the application disc.
- Page 19 7-4 Check your comport number 1. Move the cursor to My Computer and press the right button of your mouse. Select “Content Manager.” Check USB to serial COM port number. 7-4-1 Select the same COM 7-4-2 Click “Open Port” 2. Click Dump log button (7-5) to run Data log download and check the records.
- Page 20 3. File list window will show up after download. (7-8) Click the file you want to transfer to Google earth, and set the unit (7-9) and time (7-10). The default recording time is Greenwich Mean Time, that user could change time in different district.
- Page 21 3100553871 Version 1.0 May. 2007...
Need help?
Do you have a question about the GPS Bluetooth Receiver IGO-08A and is the answer not in the manual?
Questions and answers