Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Emprex iGO-08C
Summary of Contents for Emprex iGO-08C
- Page 1 GPS Bluetooth Receiver IGO-08C User’s Guide Version 1.0...
- Page 2 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Page 3: Table Of Contents
Table of Content Introduction ...1 Features ...1 Package content...2 Hardware Description ...3 Technology Specification ...5 Operation ...7... -
Page 4: Introduction
Introduction IGO-08C is a GPS receiver with Bluetooth interface adopts advanced ATMEL ANTARIS 4 Super Sense GPS IC, and built-in active antenna for high sensitivity to tracking signal, there’s also an external MMCX aerial terminal for users adding higher MMCX antenna. -
Page 5: Package Content
Please make sure of your package includes the following items, If any item is damaged or missing, please contact your dealer at once. Bluetooth GPS receiver IGO-08C x 1 Lithium rechargeable battery x 1 USB cable x 1 Slipperiless pad x 1... -
Page 6: Hardware Description
Hardware Description There are four LEDs to show different status: Bluetooth（Blue） Fast blink: Indicates this Bluethooth GPS is waiting for Slow blink: Indicates this Bluetooth GPS is connecting Power LED（Red） Lighten: Charging Darken: Charging complete GPS （Green） Lighten: GPS power on Darken: GPS power off pairing or master device’... -
Page 7: Power Switch
Circle LED (Red) Battery capacity display Charge socket Battery bolt Switch 1 ( Long press: Special location record Short press: Data logger capacity display Switch 2 ( Long press: PC connecting mode On/Off Short press: BT function On/OFF Power switch Long press: Power On/ Off Short press: Power capacity display on circle LED MMCX Antenna Socket... -
Page 8: Technology Specification
Technology Specification Receiving and tracking 16 satellites at the same time Satellite receiving Receiving frequency: 1575.42MHz Receiving code: L1, C/A code Accuracy General positioning: 2.5m CEP (Precision) DGPS/SBAS: 2.0m CEP Acquisition Cold start: 34 sec (Average) Warm start: 33 sec (Average) Hot start: 1 sec (Min) Sensitivity: -158dBm (Super sense mode) - Page 9 Data logger 25806 records Power supply: DC 5.0V Power 70mA (Average) consumption Operating -10°C~ +60°C Temp. Storage Temp. -20°C~ +85°C Humidity 5%~95% Size: 64(L) x 41 (W) x 19 (H)mm Weight 54g (include battery) Battery: Nokia 6100 compatible (spec. 3.7V / 700mA ) Operating Hour Up to 10 hours at battery full charge condition Output connect Mini-USB (TTL Level)
-
Page 10: Operation
LED goes off indicates finish charging. 1-2. Battery capacity check Press the Power Switch for 1 second when the IGO-08C is power on; the circle LED shows battery capacity. Each LED equals 12.5% power. Eight LED lighten shows full battery. - Page 11 PDA or dangle. A virtual comport will be assigned after Bluetooth connection is successful. Every time you want to connect IGO-08C with a new Master Bluetooth device, which never pair before, user has to push pairing switch of your master bluetooth device first.
- Page 12 PC, the special location will be marked bigger white spot (a tack pattern) on the map 4. Before connecting IGO-08C with your PC to run Data logger setup and download, please shut down the GPS Receiver. (Long press Switch 2 ( 5.
- Page 13 A1. Stop Data logger A2. Start Driving Mode A3. Start Hiking Mode Attention 1. Users could choose to start Data logger function or not. Special location record is still available when data logger function is off if you long press Switch 1 ( seconds 2.
- Page 14 Hiking mode is recorded by steady time.
- Page 15 7. IGO-08 Download software 7-1 Install the IGO Logger 7-1-1 Please insert the application disc. Select “iGO Logger” file and click Next to continue 7-1-2 Select “Myself” and click Next.
- Page 16 7-1-3 It’s ready to install, please click Next. 7-1-4 Please wait. 7-1-5 IGO Logger has installed successfully.
- Page 17 7-3 Connect with USB cable Plug one end of the USB cable to the USB port on your computer. Connect the other end of the USB cable to the USB socket of IGO-08C. 7-2-1 Please insert the application disc. Select “PL-2303 Driver Installer”...
- Page 18 7-4 Check your comport number 1. Move the cursor to My Computer and press the right button of your mouse. Select “Content Manager.” Check USB to serial COM port number. 7-4-1 Select the same COM 7-4-2 Click “Open Port” 2. Click Dump log button (7-5) to run Data log download and check the records.
- Page 19 3. File list window will show up after download. (7-8) Click the file you want to transfer to Google earth, and set the unit (7-9) and time (7-10). The default recording time is Greenwich Mean Time, that user could change time in different district.
- Page 20 3100553870 Version 1.0 Jan. 2007...
Need help?
Do you have a question about the iGO-08C and is the answer not in the manual?
Questions and answers