Table of Contents
Advertisement
BATTERY CAUTIONARY INSTRUCTIONS
BATTERIES: CAUTION
To reduce the risk of fire or injury to persons, read and follow these instructions:
• For the cordless handset, use only 3.6V 400mAh Nickel-Cadmium (Ni-Cd), cordless
telephone battery pack, 35BAT (included).
• Do not dispose of the batteries in a fire. The cells may explode. Check with local codes
for possible special disposal instructions.
• Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to short the battery with conducting
materials such as rings, bracelets, and keys. The battery or conductor may overheat
and cause burns.
• Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may occur causing burns or
irritation to eyes or skin.
• When inserting batteries into this product, the proper polarity or direction must be
observed. Reverse insertion of batteries can cause charging, and that may result in
leakage or explosion.
• Remove the batteries from this product if the product will not be used for a long period
of time (several months or more) since during this time the battery could leak in the
product.
• Do not store this product, or the batteries identified for use with this product, in high
temperature areas. Batteries that are stored in a freezer or refrigerator for the purpose
of extending shelf life should be protected from condensation during storage and
defrosting.
Batteries should be stabilized at room temperature prior to use after cold storage.
The EPA certified RBRC
(Ni-Cd) battery indicates Aastra Telecom is voluntarily participating in an
industry program to collect and recycle these batteries at the end of their
useful life, when taken out of service in the United States or Canada.
The RBRC
®
program provides a convenient alternative to placing used
Ni-Cd batteries into the trash or the municipal waste stream, which may
be illegal in your area. Please call 1-800-8-BATTERY for information on
Ni-Cd battery recycling and disposal bans/restrictions in your area.
Aastra Telecom's involvement in this program is part of our commitment to
preserving our environment and conserving our natural resources.
®
Battery Recycling Seal on the nickel-cadmium
5
BE-3872 PARTS CHECKLIST
2.4
GHz
In Use/
Low Batt.
Mute
MEM
1. Handset
3. AC power adapter
4. 10-number
QUICK START GUIDE
BE-3872
SETTING UP THE BASE
1. Install a 9V backup battery into the battery compartment,
located on the base bottom.
2. Connect the telephone line cord to the "LINE" jack and to
a telephone outlet.
3. Connect the AC power adapter to the 9V DC jack and to
an AC outlet. Wait 15 seconds for the answering system
to reset before using the base.
Note: Use only the supplied AC power adapter. Connect the AC power
adapter to a continuous power supply.
INSTALL THE BATTERY
1. Slide open the battery compartment door on the bottom of the
handset.
2. Insert the battery into the battery compartment and then plug the
battery connector into the 2-pin connector located just inside the
battery compartment.
3. Close the battery compartment door and place the handset on the
base unit cradle. You will hear a tone and the CHARGE LED on the
base will illuminate.
4. IMPORTANT: Charge the battery pack for at least 12 hours before
using the handset the first time.
DAY AND TIME SETTING ON THE ANSWERING MACHINE
1.
Press and hold [Time Set] for three seconds until "Monday" is heard.
2.
Press the 7 /Repeat or 8 /Skip key to select the current day of the week. Press
[Time Set] to store that information. "12 AM" will be announced.
3.
Press 7 /Repeat or 8 /Skip to select the current hour (1AM through 12AM or 1PM
through 12PM). Press [Time Set]. "00" will be announced.
4.
Press 7 /Repeat or 8 /Skip as many times necessary to set the current minutes (01
through 59). Press [Time Set] again. The information will be stored and the new
day and time will be announced.
CHANGING THE ANSWER MODE
There are three answering modes: Answer On, Answer Only, or Answer Off.
Turning the Answering System On/Off: When the answering machine is set off, the
caller will not hear an announcement and will not be able to leave a message.
1.
Press the [ANS On/Off] key to turn the answering machine on or off. The system
will announce the current on/off status of the answering machine.
Choosing between Answer On and Answer Only: Make sure that the answering
machine is on. Locate the ANS ONLY On/Off switch on the base bottom.
If the ANS ONLY switch is set to "Off," the BE-3872 will play your announcement, and
then allow the caller to leave a message.
If the ANS ONLY switch is set to "On," the BE-3872 will play your answer-only announce-
ment, and then disconnect the call. The caller is unable to leave any messages.
7. Ni-Cd battery pack
6. Quick start card
7
8
2. Base
5. 7-foot line
cord for desk use
memory card
8. Belt-Clip
1. Dial the answering machine
phone number.
2. Press *, and then enter the
two-digit remote code.
3. If you entered the correct code,
the phone will announce the
number of messages and begin
playing the voice help menu.
4. Once the voice help menu
begins, enter your commands.
5. When finished, hang up.
Write 2-digit r
rite 2-digit remote code
in boxes
in boxes
9. Remote Access
Card
6
emote code
Advertisement
Table of Contents
