Page 1: About This Manual
Projector CP-X265 User's Manual – Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read the "User's Manual - Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual.
Page 2: Table Of Contents
Content Content   About this manual . . . . . . . . . . 1 EASY Menu ....5 Aspect, Auto keystone Execute, Content .
Page 3: Projector Features
Projector features / Preparations Projector features This projector is used to project various computer signals as well as NTSC/PAL/ SECAM, Component (SD, HD) video signals onto a screen. It requires just a little space for installation and gets a large image from short distance. ...
Page 4: Part Names
Part names Part names Projector ê Control buttons (6) Lamp cover (54) Remote sensor (16) (Lamp unit is inside.) Speaker Zoom ring (19) Security bar (10) Focus ring (19) (Use for attaching a commercial anti-theft chain or wire.) Vent Elevator button (9) Lens (17) Elevator foot (9) Front-Right side...
Page 5 Part names Power switch (17) AC inlet (14) Elevator button (9) Ports (See below.) Elevator foot (9) Vent Rear-Left side AUDIO IN port (12) (In the default setting, the AUDIO IN port is the audio port for the RGB IN port, however, it is possible to AUDIO IN3 L/R port (13) change the settings.
Page 6: Control Buttons
Part names Control buttons LAMP indicator (60, 61) TEMP indicator (60, 61) Cursor buttons POWER indicator (17, 60, 61) ▲,▼,◄,► (24) STANDBY/ON button (17) INPUT button (18) Remote control SEARCH button (19) STANDBY/ON button (17) RGB button (18) AUTO button (20) SEARCH VIDEO VIDEO button (19)
Page 7: Setting Up
Setting up Setting up WARNING ►Place the projector in a stable position horizontally. A fall or a turnover could cause an injury and/or damage to the projector. Then using damaged projector could result in a fire and/or an electric shock. •...
Page 8: Arrangement
Setting up Arrangement Refer to the illustrations and tables below to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen: 04×768 (a) The screen size (diagonal) (b) Distance from the projector to the screen (±0%) (c) The height of the screen (±0%) (c) up 6:9...
Page 9: Adjusting The Projector's Elevator
Setting up Adjusting the projector's elevator CAUTION ►If you press the elevator button without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet.
Page 10: Using The Security Bar
Setting up Using the Security Bar WARNING ►Do not use the security bar to prevent the projector from falling. Dropping or knocking over the projector may cause damage or injury. CAUTION ►The security bar is not a comprehensive theft prevention measure.
Page 11: Connecting Your Devices
Setting up Connecting your devices CAUTION ►Turn off all devices prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector.
Page 12: Examples Of Connection With A Computer
Setting up Examples of connection with a computer * In the default setting, the AUDIO IN port is the audio port for the RGB IN, and the AUDIO IN port is the audio port for the RGB IN ports. To change the settings, refer to the AUDIO item in the SETUP menu.
Page 13: Video Out
Setting up Examples of connection with a VCR/DVD player * In the default setting, the AUDIO IN3 L/R port is the audio port for the VIDEO, S-VIDEO and COMPONENT VIDEO ports. To change the settings, refer to the AUDIO item in the SETUP menu.
Page 14: Connecting Power Supply
Setting up Connecting power supply WARNING ►Please use extra caution when connecting the power cord, as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.
Page 15: Remote Control
Remote control Remote control Putting batteries WARNING ►Always handle the batteries with care and use them only as directed. Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. And also improper use may result in cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
Page 16: Using The Remote Control
Remote control Using the remote control CAUTION ►Be careful in handling the remote control. • Do not drop or expose the remote control to physical impact. • Do not get the remote control wet or place it on wet objects. It may result in malfunction.
Page 17: Power On/Off
Power on/off Power on/off WARNING ►When the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole. NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices.
Page 18: Operating
Operating Operating Adjusting the volume Press the VOLUME button on the remote control. A dialog will appear on the screen to aid you in adjusting the volume. SEARCH VIDEO BLANK Use the cursor buttons ▲/▼ to adjust the volume. ASPECT AUTO MAGNIFY To close the dialog and complete the operation, press the...
Page 19: Searching An Input Signal
Operating Selecting an input signal (continued) Press the VIDEO button on the remote control to select an input for video signal. SEARCH VIDEO Each time you press the button, the projector switches its BLANK ASPECT AUTO video input port as below. MAGNIFY HOME PAGE UP...
Page 20: Using The Automatic Adjustment Feature
Operating Using the automatic adjustment feature Press the AUTO button on the remote control. SEARCH VIDEO  For an RGB signal BLANK ASPECT AUTO The vertical position, the horizontal position, the horizontal phase and the horizontal size will be automatically adjusted. MAGNIFY HOME PAGE UP...
Page 21: Correcting The Keystone Distortions
Operating SEARCH VIDEO Correcting the keystone distortions BLANK ASPECT AUTO Press the KEYSTONE button on the MAGNIFY HOME PAGE UP VOLUME remote control. A dialog will appear on the PAGE DOWN MUTE screen to aid you in correcting the distortion. FREEZE MY BUTTON KEYSTONE...
Page 22: Freezing The Screen
Operating VIDEO SEARCH Freezing the screen ASPECT AUTO BLANK Press the FREEZE button on the remote control. MAGNIFY PAGE UP VOLUME HOME The “FREEZE” indication will appear on the screen, and the PAGE DOWN MUTE projector will enter the FREEZE mode. FREEZE MY BUTTON KEYSTONE...
Page 23: Operating The Computer Screen
Operating Operating the computer screen CAUTION ►Mistaken use of the mouse/keyboard control could damage your equipment. • While using this function, please connect only with a computer. • Before connecting, read the manuals of the computer you will connect. NOTE • It may not be possible to control notebook PC, and other computers with built-in pointing device (e.g.
Page 24: Multifunctional Settings
Multifunctional settings Multifunctional settings Using the menu function VIDEO SEARCH This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, ASPECT AUTO BLANK OPTION, NETWORK, and EASY MENU. EASY MENU consists of functions often MAGNIFY PAGE UP HOME VOLUME used, and the other menus are classified into each purpose.
Page 25: Easy Menu
EASY Menu EASY Menu With the EASY MENU, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control. Then perform it referring to the following table. Item Description Using the buttons ◄/►...
Page 26 EASY Menu EASY Menu (continued) Item Description Using the buttons ◄/► adjusts the contrast. CONTRAST See the CONTRAST item in the PICTURE menu (27). Using the buttons ◄/► adjusts the strength of whole color. COLOR See the COLOR item in the PICTURE menu (28). Using the buttons ◄/►...
Page 27: Picture Menu
PICTURE Menu PICTURE Menu With the PICTURE menu, the items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item.
Page 28 PICTURE Menu PICTURE Menu (continued) Item Description Using the buttons ▲/▼ switches the mode of color temperature. HIGH DEFAULT � HIGH CUSTOM � MID DEFAULT � MID CUSTOM LOW DEFAULT � LOW CUSTOM � Hi-BRIGHT-1 DEFAULT � Hi-BRIGHT-1 CUSTOM Hi-BRIGHT-2 DEFAULT � Hi-BRIGHT-2 CUSTOM To adjust CUSTOM Selecting the CUSTOM and then pressing the ENTER :...
Page 29 PICTURE Menu PICTURE Menu (continued) Item Description Selecting a mode of MY MEMORY using the buttons ▲/▼ and then pressing the button ► or the ENTER button performs each function. LOAD ó LOAD ó LOAD3 ó LOAD4 SAVE4 óSAVE3 ó SAVE ó SAVE This projector has 4 numbered memories for adjustment data.
Page 30: Image Menu
IMAGE Menu IMAGE Menu With the IMAGE menu, items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item.
Page 31 IMAGE Menu IMAGE Menu (continued) Item Description Using the buttons ▲/▼ adjusts the horizontal size. Large ó Small • This item can be selected only for an RGB signal. H SIZE • When this adjustment is excessive, the picture may not be displayed correctly.
Page 32: Input Menu
INPUT Menu INPUT Menu With the INPUT menu, the items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item.
Page 33 INPUT Menu INPUT Menu (continued) Item Description Using the buttons ▲/▼ switches the function of COMPONENT VIDEO port. COMPONENT ó SCART RGB When the SCART RGB is selected, the COMPONENT VIDEO port COMPONENT function as a port for a SCART RGB signal input and VIDEO port function as a port for SCART RGB sync input.
Page 34 INPUT Menu INPUT Menu (continued) Item Description The resolution for the RGB and RGB input signals can be set on this projector. (1) In the INPUT menu select RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed. () In the RESOLUTION menu select the resolution you wish to display using the ▲/▼...
Page 35: Setup Menu
SETUP Menu SETUP Menu With the SETUP menu, the items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item.
Page 36 SETUP Menu SETUP Menu (continued) Item Description Using the buttons ▲/▼ switches the mode for mirror status. NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT MIRROR If Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (48) will be displayed when projector is restarted after the power switch is turned off.
Page 37: Screen Menu
SCREEN Menu SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item.
Page 38 SCREEN Menu SCREEN Menu (continued) Item Description Using the buttons ▲/▼ switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen ó ORIGINAL ó TURN OFF MyScreen is a screen you can register as a desired screen.The ORIGINAL screen is the existing standard screen.
Page 39 SCREEN Menu SCREEN Menu (continued) Item Description Using the buttons ▲/▼ turns on/off the message function. TURN ON ó TURN OFF When the TURN ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting ”NO INPUT IS DETECTED” ”SYNC IS OUT OF RANGE”...
Page 40: Option Menu
OPTION Menu OPTION Menu With the OPTION menu, the items shown in the table below can be performed. Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item, except for the items LAMP TIME and FILTER TIME.
Page 41 OPTION Menu OPTION Menu (continued) Item Description Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE) AUTO OFF AUTO OFF ENABLE DISABLE When the time is set to 0, the projector is not turned off automatically.
Page 42 OPTION Menu OPTION Menu (continued) Item Description Selecting this item displays the SERVICE menu. Select an item using the buttons ▲/▼, and press the button ► or the ENTER button on the remote control to execute the item. FAN SPEED ó AUTO ADJUST ó GHOST ó FILTER MESSAGE ó KEY LOCK FACTORY RESET ó...
Page 43 OPTION Menu OPTION Menu (continued) Item Description REMOTE FREQ. Use the ▲/▼ button to change the Projector's remote sensor setting (16). :NORMAL ó :HIGH Items with a checkmark are on. The factory default setting is for both :NORMAL and :HIGH to be on. If the remote control does not function correctly set the this to either only or only as described in Remote Control Settings (16).
Page 44 OPTION Menu OPTION Menu (continued) Item Description This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer. 1. Using Security Features 1.1 Inputting the PASSWORD 1.1-1 Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ►...
Page 45: Using The Myscreen Password Function
OPTION Menu OPTION Menu (continued) Item Description 1.3 If you have forgotten your PASSWORD .3- Follow the procedure in .- to display the ENTER PASSWORD BOX. .3- While the ENTER PASSWORD BOX is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT and ►...
Page 46: Using The Pin Lock Function
OPTION Menu OPTION Menu (continued) Item Description .-4 Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to display the PASSWORD for about 0 seconds, please make note of the PASSWORD during this time.
Page 47 OPTION Menu OPTION Menu (continued) Item Description 3.1-3 Input a 4 part PIN Code using the ▲/▼/◄/► /RGB and INPUT buttons. A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code registration. PIN BOX NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close.
Page 48: Using The Transition Detector Function
OPTION Menu OPTION Menu (continued) Item Description 4. Using the Transition Detector Function While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below. • Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.
Page 49 OPTION Menu OPTION Menu (continued) Item Description 4.3 Setting the Transition Detector off 4.3- Follow the procedure in 4.- to display the Transition Detector on/off menu. 4.3- Select TURN OFF to display the ENTER PASSWORD BOX (large). Enter the registered PASSWORD and the screen will return to the Transition Detector on/off menu.
Page 50: Network Menu
NETWORK Menu NETWORK Menu Select [Network] from the main menu to access the following functions. NOTE • The factory default setting for DHCP is “TURN ON”. You do not have to set up [DHCP], [IP ADDRESS], [SUBNET MASK] or [DEFAULT GATEWAY] if your network has DHCP enabled.
Page 51 NETWORK Menu NETWORK Menu (continued) Item Operation Input the DEFAULT GATEWAY : Use the ▲/▼/◄/► buttons to enter the DEFAULT DEFAULT GATEWAY (a node on a computer network that serves DEFAULT GATEWAY GATEWAY as an access point to another network) address. This function is available as long as DHCP is set to “TURN OFF”.
Page 52 NETWORK Menu NETWORK Menu (continued) Item Operation INFORMATION display : Use the ► or ENTER buttons to view network information and confirm settings. INFORMATION ~Note~ • Only the first 16 characters of the projector name are displayed. • When the voltage level of battery for built in clock decreases, set time may become incorrect even though accurate date and time are input.
Page 53: Maintenance
Maintenance Maintenance Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Page 54 Maintenance Lamp (continued) A lamp has a finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.
Page 55: Air Filter
Maintenance Air filter WARNING ►Before caring, make sure the power switch is off and the power cable is not plugged in, then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause an electric shock, a burn and/or malfunction to the projector.
Page 56 Maintenance Air filter (continued) Apply a vacuum cleaner to the air filter and the filter cover. Please replace the air filter when it is damaged or too soiled. Replace the air filter in its original position. Secure the air filter in place by pressing each of the six locations.
Page 57: Replacing Internal Clock Battery
Press the metal claw of the battery holder. Then the battery Metal claw will come up. Remove the battery. Put a new battery in. Replace battery with HITACHI MAXELL, Part No.CR2032 only. Use of another battery may present a risk of fire or explosion. “+” marking...
Page 58: Other Care
Maintenance Other care WARNING ►Before caring, make sure the power switch is off and the power cable is not plugged in, and then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector.
Page 59: Troubleshooting
Troubleshooting Troubleshooting Related messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.
Page 60: Regarding The Indicator Lamps
Troubleshooting Regarding the indicator lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please follow the instructions within the table. If the same indication is displayed after the remedy, or if an indication other than the following is displayed, please contact your dealer or service company.
Page 61 Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP Description indicator indicator indicator The cooling fan is not operating. Please turn the power off, and allow the projector to Blinking cool down at least 0 minutes. After the projector has Turned Blinking sufficiently cooled down, please make confirmation...
Page 62: Phenomena That May Be Easy To Be Mistaken For Machine Defects
Troubleshooting Phenomena that may be easy to be mistaken for machine defects WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet.
Page 63 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The signal cables are not correctly connected. ,3 Correctly connect the audio cables. The MUTE function is working. Restore the sound pressing the MUTE or VOLUME button on the remote control.
Page 64 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The brightness and/or contrast are adjusted to an extremely low level. 5, 6 Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function.
Page 65: Warranty And After-Service
Warranty And After-Service Warranty and after-service If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied. Specifications Specifications NOTE •...
Page 66 Specifications Specifications (continued) S-VIDEO VIDEO CONTROL AUDIO AUDIO AUDIO AUDIO 306 mm...
Page 67: Projector Control
Projector CP-X265 User’s Manual – Network Functions This manual is only intended to explain Network Functions. For safety, operations or any other issues, refer to the User’s Manual, Quick Start Guide or Safety Guide. WARNING • Before using the network functions, read the User’s Manual and Quick Start Guide carefully to ensure your projector is set up correctly.
Page 68: Configuring And Controlling The Projector Via A Web Browser
Network Functions Network Functions This projector is equipped with the following network functions. Configuring and Controlling the Projector via a Web Browser You can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network. (4) Failure &...
Page 69: Before Using The Network Functions
Network Functions Before using the network functions… To use the network functions of this projector, the projector must be configured to suit your network. Consult with your network administrator before connecting the projector to your network. Incorrect network configuration of this projector may cause problems on your network.
Page 70 Network Functions Configuring and controlling the projector via a web browser You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network. NOTE • Internet Explorer 5.5 or higher or Netscape 6.2 or higher are required. •...
Page 71 Network Functions Configuring and controlling the projector via a web browser (Continued) When configuring or controlling the projector via a web browser, an ID and password are required. There are two types of IDs, Administrator IDs and User IDs. The following chart describes the differences between user and administrator IDs.
Page 72 Settings Settings Refer to the following for configuring or controlling the projector via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: ) Enter Fig. [https://192.168.1.10] into the address bar of the web browser and the screen in Fig.
Page 73: Network Information
Settings Network Information All screen images displayed in this manual are screens of a logon using an administrator ID. Any administrator only functions will not be displayed when using a user ID. Refer to the descriptions in each table. Displays the projector’s current network configuration settings. Item Description DHCP...
Page 74: Network Settings
Settings Network Settings Displays and configures network settings. Item Description IP Configuration Configures network settings. DHCP ON Enables DHCP. DHCP OFF Disables DHCP. IP Address Configures the IP address when DHCP is disabled. Subnet Mask Configures the Subnet Mask when DHCP is disabled. Default Gateway Configures the Default Gateway when DHCP is disabled.
Page 75: Port Settings
Settings Port Settings Displays and configures communication port settings. Item Description Network Control Port1 Configures command control port 1 (Port:23). (Port:23) Port open Click the [Enable] check box to use port 23. Click the [Enable] check box when authentication is required Authentication for this port.
Page 76: Mail Settings
Settings Mail Settings Displays and configures e-mail addressing settings. Item Description Click the [Enable] check box to use the e-mail function. Send Mail Configure the conditions for sending email under [Alert Settings]. SMTP Server IP Address Configures the address of the mail server in IP format. Configures the sender e-mail address.
Page 77: Alert Settings
Settings Alert Settings Displays and configures failure & warning alerts. Item Description Cover Error Configures Cover Error alert settings. Click the [Enable] check box to enable SNMP Trap alerts for SNMP Trap this item. Click the [Enable] check box to enable e-mail alerts for this Send Mail item.
Page 78 Settings Alert Settings (Continued) Item Description Lamp Error Configures Lamp Error alert settings. Click the [Enable] check box to enable SNMP Trap alerts for SNMP Trap this item. Click the [Enable] check box to enable e-mail alerts for this Send Mail item.
Page 79 Settings Alert Settings (Continued) Item Description Lamp Time Error Configures Lamp Time Error alert settings. Click the [Enable] check box to enable SNMP Trap alerts for SNMP Trap this item. Click the [Enable] check box to enable e-mail alerts for this Send Mail item.
Page 80 Settings Alert Settings (Continued) Item Description Other Error Configures Other Error alert settings. Click the [Enable] check box to enable SNMP Trap alerts for SNMP Trap this item. Click the [Enable] check box to enable e-mail alerts for this Send Mail item.
Page 81 Settings Alert Settings (Continued) Item Description Filter Time Alarm Configures Filter Time Alarm alert settings. Alarm Time Configures the filter time to alert. Click the [Enable] check box to enable SNMP Trap alerts for SNMP Trap this item. Click the [Enable] check box to enable e-mail alerts for this Send Mail item.
Page 82: Schedule Settings
Settings Schedule Settings Displays and configures schedule settings. Item Description Daily Configures the daily schedule. Schedule Click the [Enable] check box to enable daily scheduling. Schedule List Displays the current daily schedule. Sunday Configures the Sunday schedule. Schedule Click the [Enable] check box to enable Sunday scheduling. Schedule List Displays the current Sunday schedule.
Page 83 Settings Schedule Setting (Continued) Item Description Specific date No1 Configures the specific date (No.1) schedule. Click the [Enable] check box to enable specific date (No.1) Schedule scheduling. Month/Day Configures the Month and date. Schedule List Displays the current specific date (No.1) schedule. Specific date No.2 Configures the specific date (No.2) schedule.
Page 84 Settings Schedule Setting (Continued) To add additional functions and events click the [Add] button and set the following items. Item Description Time Configures the time to execute commands. Command Configures the commands to be executed. Power Parameter Configures the parameters for power control. Input Source Configures the parameters for input switching.
Page 85 Settings Date/Time Settings (Continued) Item Description Click the [ON] check box to enable daylight savings time and Daylight Savings Time set the following items. Start Configures the date and time daylight savings time begins. Month Configures the month daylight savings time begins (1~12). Configures the week of the month daylight savings time Week begins (First, 2, 3, 4, Last).
Page 86: Security Settings
Settings Security Settings Displays and configures passwords and other security settings. Item Description Administrator authority Configures the Administrator ID and Password. Configures the Administrator ID. Administrator ID The length of the text can be up to 32 alphanumeric characters. Configures the Administrator Password. Administrator The length of the text can be up to 255 alphanumeric Password...
Page 87 Settings Security Settings (Continued) Item Description Configures the Authentication Password for the command Network Control control. Configures the Authentication Password. Authentication The length of the text can be up to 16 alphanumeric Password characters. Re-enter Authentication Used to re-enter the above password for verification. Password SNMP Configures the community name if SNMP is used.
Page 88 Projector Control Projector Control Projector Control The items shown in the table below can be performed using the [Projector Control] menu. Select an item using the up and down arrow keys on the PC. Most of the items have a submenu. Refer to the table below for details.
Page 89 Projector Control Projector Control (Continued) Item Description Image Aspect Selects the Aspect setting. Over Scan Selects the Over Scan setting. V Position Adjusts the V Position. H Position Adjusts the H Position. H Phase Adjusts the H Phase. H Size Adjusts the H Size.
Page 90 Projector Control Projector Control (Continued) Item Description Screen Language Selects the Language for the OSD. Menu Position V Adjusts the vertical Menu Position. Menu Position H Adjusts the horizontal Menu Position. Blank Selects the Blank mode. Startup Selects the Startup screen mode. MyScreen Lock Turns MyScreen Lock On/Off.
Page 91: Projector Status
Projector Control Projector Status Displays and configures the current projector status. Item Description Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current filter. Power Status Displays the current power status.
Page 92 Failure & Warning Alerts via E-mail Failure & Warning Alerts via E-mail The projector can automatically send an alert to specified e-mail addresses when the projector requires maintenance or has encountered an error. NOTE • Up to five e-mail addresses can be specified. •...
Page 93 Failure & Warning Alerts via E-mail Mail Settings (Continued) 8) Configure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings] on the main menu. 9) Select and configure each alert item. Refer to [Alert Settings] in [Configuring and Controlling the Projector via a Web Browser] for further information. 10) Click the [Apply] button to save the settings.
Page 94 Projector management via SNMP Projector management via SNMP When SNMP is enabled, the projector is able to send Failure/Warning Alerts to a specified PC. NOTE • It is recommended that SNMP functions be carried out by a network administrator. • SNMP management software must be installed on the computer to monitor the projector via SNMP.
Page 95 Controlling the Projector via Scheduling Controlling the Projector via Scheduling The projector can be automatically controlled via scheduling. NOTE • You can schedule the following control events: Power ON/OFF, Input Source and Transferred Image Display. • There are 3 types of Scheduling, 1) daily 2) day of the week 3) specific date. •...
Page 96 Controlling the Projector via Scheduling Date/Time Settings (18) The Date/Time setting can be adjusted via a web browser. Example: If the IP address of the projector is set to 192.168.1.10: ) Enter [https://192.168.1.10] into the address bar of the web browser. Enter the Administrator ID and Password and click [Logon].
Page 97 Controlling the Projector via Scheduling Schedule Settings (16) Schedule settings can be configured from a web browser. Example: If the IP address of the projector is set to 192.168.1.10: ) Enter [https://192.168.1.10] into the address bar of the web browser. ) Enter the Administrator ID and Password and click [Logon].
Page 98: Communication Port
e-Shot (Still Image Transfer) Display e-Shot (Still Image Transfer) Display The projector can display a still image that is transferred via the network. Communication Port The following port is used for e-Shot. TCP #9716 (9) NOTE • e-Shot is not available via communication ports which are used for the command control (TCP #23 and TCP #9715).
Page 99 The network connection can be restarted using [Network Restart] on the main menu. e-Shot (Still Image Transfer) Transmission e-Shot transmission requires an exclusive application for your PC. You can download it from the Hitachi web site. Refer to the manual for the application for instructions.
Page 100 Command Control via the Network Command Control via the Network You can configure and control the projector via the network using RS-232C commands. Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 NOTE •...
Page 101 Command Control via the Network Command Control Settings (Continued) When the authentication setting is enabled, the following settings are required. (20) ) Click [Security Settings] on the main menu. ) Click [Network Control] and enter the desired authentication password. * See Note.
Page 102: Header
Command Control via the Network Command format Command formats differ among the different communication ports. TCP #23 You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. However, the following reply will be sent back in the event of authentication failure when authentication is enabled.
Page 103 Command Control via the Network Reply Data format The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data. <ACK reply> Connection Reply 0x06 byte <NAK reply>...
Page 104 Command Control via the Network Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm.
Page 105 Projector CP-X265 User's Manual – Operating Guide Technical Example of computer signal Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 3.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8...
Page 106 Example of computer signal Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b)
Page 107 Connection to the ports Connection to the ports AUDIO IN3 RGB IN1 RGB IN2 RGB OUT AUDIO OUT AUDIO IN1 AUDIO IN2 CONTROL VIDEO S-VIDEO RGB IN1, RGB IN2, RGB OUT D-sub 5pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 5 4 3 2 75Ω...
Page 108: Component Video
Connection to the ports AUDIO IN3 RGB IN1 RGB IN2 RGB OUT AUDIO OUT AUDIO IN1 AUDIO IN2 CONTROL VIDEO S-VIDEO COMPONENT VIDEO RCA jack x3 • System: 525i(480i), 525p(480p), 625i(576i), 750p(720p), 25i(080i) Port Signal Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite Component video C , 0.7±0.1Vp-p, 75Ω...
Page 109 Connection to the ports AUDIO IN3 RGB IN1 RGB IN2 RGB OUT AUDIO OUT AUDIO IN1 AUDIO IN2 CONTROL VIDEO S-VIDEO AUDIO IN-1 ( AUDIO IN-2 AUDIO 3 L/R (RCA jack) Ø3.5 stereo mini jack), J , K L • 200mVrms(max.) 35kΩ termination AUDIO OUT ( Ø3.5 stereo mini jack) •...
Page 110 Connection to the ports AUDIO IN3 RGB IN1 RGB IN2 RGB OUT AUDIO OUT AUDIO IN1 AUDIO IN2 CONTROL VIDEO S-VIDEO RJ-45 jack Signal Signal Signal TX+ 2 TX- 3 RX+ 6 RX-...
Page 111: Communications Setting
RS-232C Communication (continued) RS-232C Communication CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - () () CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) RTS...
Page 112: Command Data Chart
RS-232C Communication (continued) Requesting projector status (Get command) () Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+ ‘00H’ +‘00H’) from the computer to the projector. (2) The projector returns the response code ‘DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) () Send the setting code Header + Command data (‘0H’+‘00H’+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector.
Page 113: Get
RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code Power Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00 00 60 01 00 BE EF 06 00 19 D3 02 00 00 60 00 00 (Example return) 00 00 01 00 02 00 (Off) (On) (Cool down) Input Source RGB IN 1 BE EF 06 00 FE D2...
Page 114 RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code User Gamma Pattern BE EF 06 00 FB FA 01 00 80 30 00 00 9 step gray scale BE EF 06 00 6B FB 01 00 80 30 01 00 15 steps gray scale BE EF 06 00 9B FB 01 00 80 30 02 00 Ramp BE EF 06 00 0B FA 01 00 80 30 03 00 BE EF 06 00 C8 FA 02 00 80 30...
Page 115 RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code COLOR TEMP GAIN G BE EF 06 00 70 F4 02 00 B2 30 00 00 Increment BE EF 06 00 16 F4 04 00 B2 30 00 00 Decrement BE EF 06 00 C7 F5 05 00 B2 30 00 00 COLOR TEMP GAIN B BE EF 06 00 8C F5 02 00 B3 30 00 00 Increment BE EF 06 00 EA F5 04 00...
Page 116 RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code ASPECT BE EF 06 00 9E D0 01 00 08 20 00 00 16:9 BE EF 06 00 0E D1 01 00 08 20 01 00 14:9 BE EF 06 00 CE D6 01 00 08 20 09 00 SMALL BE EF 06 00 FE D1 01 00 08 20 02 00 NORMAL BE EF 06 00 5E DD 01 00...
Page 117 RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code FRAME LOCK TURN OFF BE EF 06 00 CB D6 01 00 14 30 00 00 TURN ON BE EF 06 00 5B D7 01 00 14 30 01 00 BE EF 06 00 F8 D6 02 00 14 30 00 00 RGB1 IN-1 SYNC ON G OFF BE EF 06 00 5E D7 01 00 10 20 02 00 SYNC ON G ON BE EF 06 00 CE D6...
Page 118 RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code MUTE TURN OFF BE EF 06 00 46 D3 01 00 02 20 00 00 TURN ON BE EF 06 00 D6 D2 01 00 02 20 01 00 BE EF 06 00 75 D3 02 00 02 20 00 00 LANGUAGE ENGLISH BE EF 06 00 F7 D3 01 00 05 30 00 00 FRANÇAIS BE EF 06 00 67 D2...
Page 119: Increment
RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code BLANK My Screen BE EF 06 00 FB CA 01 00 00 30 20 00 ORIGINAL BE EF 06 00 FB E2 01 00 00 30 40 00 BLUE BE EF 06 00 CB D3 01 00 00 30 03 00 WHITE BE EF 06 00 6B D0 01 00 00 30 05 00 BLACK BE EF 06 00 9B D0...
Page 120: Execute
RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code REMOTE FREQ Disable BE EF 06 00 FF 3D 01 00 30 26 00 00 NORMAL Enable BE EF 06 00 6F 3C 01 00 30 26 01 00 BE EF 06 00 CC 3D 02 00 30 26 00 00 REMOTE FREQ HIGH Set Disable BE EF 06 00 03 3C 01 00 31 26 00 00 Enable BE EF...
Page 121 RS-232C Communication (continued) Command Data Names Operation Type Header Action Type Setting Code VOLUME-RGB1 BE EF 06 00 CD CC 02 00 60 20 00 00 Increment BE EF 06 00 AB CC 04 00 60 20 00 00 Decrement BE EF 06 00 7A CD 05 00 60 20 00 00 VOLUME-RGB2 BE EF 06 00 FD CD 02 00 64 20 00 00 Increment BE EF 06 00 9B CD 04 00...
Page 122 Hitachi, Ltd. Japan 292 Yoshida-cho Totsuka-ku, Yokohama-city Kanagawa 244-0817 HITACHI EUROPE LTD. HITACHI EUROPE S.A. Consumer Affairs Department 364, Kifissias Ave. & 1, Delfon Str. PO Box 3007 152 33 Chalandri Maidenhead Athens GREECE SL6 8ZE Tel: 1-6837200 UNITED KINGDOM...

This manual is also suitable for:

Cp-x256 Ed-x15

Hitachi CP-X265 User's Manual And Operating Manual

About this Manual

Content

Projector Features

Preparations

Part Names

Setting up

Remote Control

Power On/Off

Operating

Multifunctional Settings

Maintenance

Troubleshooting

Warranty and After-Service

Specifications

Consist of Header (7 Bytes) + Command Data (6 Bytes).

1 Protocol

3 Command Data

Crc_High : Upper Byte of CRC Flag for Command Data

Quick Links

About this manual

Related Manuals for Hitachi CP-X265

Summary of Contents for Hitachi CP-X265

This manual is also suitable for:

Table of Contents