Preparation For Use - Emerson EWF2006 Owner's Manual

PREPARATION FOR USE

CONNECTIONS
Cables used here are available on the market.
[ANTENNA CONNECTION]
Antenna
Cable
OR
TV signal
Incoming cable from home antenna /
cable company (No cable box)
Cable box or
Satellite box*
OR
Incoming cable from cable
company or satellite antenna
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU'AU FOND.
Note:
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. IN
●
jack before moving the unit.
[EXTERNAL CONNECTION]
VIDEO1 input (Rear)
ex.
Video Cassette Recorder
Note:
The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
●
connecting monaural audio equipment.
VIDEO2 input (Front)
ex.
Video Camera
Video Game
Note:
The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
●
connecting monaural audio equipment.
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select "VIDEO1" or "VIDEO2" mode by
pressing [INPUT SELECT] on the remote control. The input mode changes by pressing the
button as following:
TV channel VIDEO1 (Rear)
• To use the jacks on the rear of the TV, select "VIDEO1".
• To use the jacks on the front of the TV, select "VIDEO2".
INSTALLING THE BATTERIES
1 2
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
UHF/VHF Rod Antenna
(Not supplied)
OU T
IN
ANT. IN
*Note (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
S-Video Cable
(IN)
(OUT)
OR
L
(OUT)
(IN)
AUDIO IN
R
Audio Cable
Audio Cable
(OUT)
Video Cable
(IN)
(OUT)
VIDEO
Front of this TV
VIDEO2 (Front)
Install two AA batteries (supplied)
3
matching the polarity indicated inside
battery compartment of the remote con-
trol.
OPERATIONS
REMOTE CONTROL AND FRONT PANEL FUNCTION
To send infrared ray (IR) signal
Rear of this TV
Channel number buttons
CH ▲/▼ buttons
To view on-screen menu
Note:
You can test if the remote control sends out the infrared signal with an AM radio.
●
(Refer to "TROUBLESHOOTING GUIDE".)
MENU
VIDEO L - AUDIO - R HEADPHONE
Rear of this TV
ANT.IN
VIDEO
S-VIDEO
(IN)
L AUDIO R
Note:
If some digits appear in the corner of the screen when the unit is turned on for the first time,
●
press [POWER] without unplugging the power cord.
SLEEP TIMER SETTING
This function allows you to shut off the power automatically in a certain amount of time.
1) Press [POWER] to turn on the TV and press [SLEEP].
2) Within 10 seconds, press [SLEEP] repeatedly to change an amount of
time. Each time [SLEEP] is pressed, the time increases by 10 minutes
up to 90 minutes.
Notes:
When you disconnect the unit from the AC outlet or when you have a power failure, the sleep
●
time will be lost.
To cancel the sleep timer, press [SLEEP] repeatedly until "SLEEP 0" is displayed.
●
The Sleep Timer Setting display will disappear automatically after 10 seconds of the operation.
●
IR transmitter
POWER
GAME SLEEP
POWER button
DISPLAY
To turn TV on/off
1 2 3
4 5 6
CHANNEL
RETURN
7 8 9
0 +100
INPUT
SELECT
To select channel
CH
VOL VOL
CH
MUTE
MENU button MENU
Y VOLUME X L CHANNEL K POWER
MENU Y VOLUME X L CHANNEL K
L - AUDIO - R HEADPHONE
MENU button
To view on-screen menu
HEADPHONE jack
AUDIO L/R input jacks
VIDEO input jack
GAME button
SLEEP button
DISPLAY button
To display CH No./Audio Status
CHANNEL RETURN button
To return to previous channel
INPUT SELECT button
To select TV or external input
MUTE button
▲/▼ buttons
VOL
To adjust volume
POWER
Infrared Sensor Window
POWER button
To turn TV on/off
CHANNEL ▲/▼ buttons
To select channels
VOLUME X X / Y Y buttons
To adjust volume
SLEEP 10