Function Keys; Power Supply; Warranty Registration - Dymo 1000 User Manual

Introduction
The Dymo 1000+ Electronic Labelmaker enables
you to create a wide variety of high quality self-
adhesive labels of up to 100 characters.
The Labelmaker uses 6mm (
12mm ( 1 / ") wide tape cassettes in a number of
2
label colours. Labels are tab-cut for easy removal
from the backing tape. Text can be printed
horizontally or
of sizes and styles and is always centred on the label.

Warranty Registration

Please complete the warranty registration card and
return it to your national customer service address
within seven days– see the warranty booklet for details.

Power Supply

BATTERIES
• Apply pressure to thumb catch and open hinged
access door – see fig A, page 2.
• Insert six size AA alkaline or re-chargeable
nickel-cadmium batteries, observing the polarity
markings A , and close cover.
• Remove batteries if the Labelmaker is to be
unused for some time.
AC ADAPTOR (optional)
• Connect the AC adaptor to socket A
the adaptor plug disconnects the supply from
the batteries.
• Unplug the AC adaptor from the Labelmaker
before disconnecting the mains power to the
adaptor, otherwise last label memory settings
will be lost (see also ON/OFF
Changing the cassette
• Open hinged access door as above.
• Hold as shown, then lift cassette B
and out.
• Ensure tape and ribbon B
mouth of cassette and tape passes between
guide posts before installing as shown. If
necessary, turn spool B
ribbon.
• Insert cassette and push firmly C
clicks into place.
• Ensure tape and ribbon are positioned as shown
between pinch roller C
• When using 6mm cassettes (
to slide switch B
cassettes. A notch in the cassette will fit over the
switch when correctly set.
The Display
The display shows:
• Up to eight text characters, plus the cursor,
at one time.
Use or to move along the text.
1 3
/ "), 9mm ( / ") or
4 8
in a variety
.
Inserting
).
straight up
are taut across
clockwise to tighten
until it
and print head C
1 / ") it is necessary
4
to the left prior to inserting
• Eight indicators – as shown below.
• The display will flash if you press an
incorrect key in a function sequence.
CAPS on
CAPS
Shift on

Function keys

ON/OFF
Switches the power on and off.
• Switches off automatically after two minutes if
no keys are pressed. The last label created will
be retained and displayed when next turned on.
Any stored last label settings will also be
retained.
Note: If the batteries are removed for more than a
few seconds, all text and settings will be lost.
When power is restored, the display will show a
flashing cursor (no text) and the settings will be
full height standard width text with
other settings off.
CAPITALS
• Press for all subsequent characters in UPPER
CASE (CAPITALS), as confirmed by the CAPS
indicator in the display.
• Press again to cancel and return to lower case.
SHIFT KEY
• Press and release
alphabet key to produce an UPPER CASE (CAPS)
character.
• For dual purpose keys, press
produce the legend above the key.
• Pressing
case character.
DELETE
DEL
• Press to delete the character to the left of the
cursor, or to exit certain function key operations.
CLEAR TEXT
.
• Press to clear all the current text and cancel any
fixed length setting, but leave the text size and
other settings unchanged. Also use to exit or
clear certain function key operations.
CURSOR KEYS
• Press to move the cursor along the text, one
character at a time.
• Press and hold to scan quickly through the text.
3
Italic
Box Underline
-
ITALIC
1 2 3 4 5 6 7 8
CURSOR
CAPS
Press only - DO NOT HOLD DOWN
before pressing an
while is set will give a lower
CAPS
CLEAR
+
DEL
or
GB
Vertical
Outline
text
OUTLINE
VERT
LENGTH
SET
Fixed label
length set
and all
first to