Automatic Search; Clear All - Sansui HDLCDVD265 Owner's Manual

CABLE CHART
The chart below is typical of many cable system
channel allocations.
NOTE:
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.

Automatic search

1
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
2
Press ▲ or ▼ to select "Channel", then press ▶ or
ENTER.
3
Press ▲ or ▼ to select "Auto Ch Memory", then
press ▶ or ENTER.
4
Press ▲ or ▼ to select "Automatic Search", then
press ▶ or ENTER.
Auto Ch Memory
Signal Type Cable
Automatic Search Stop
Analog Channel Found : 7
Digital Channel Found : 5
Programming Now
: Select ENTER:Cancel
5
The TV will begin memorizing all the channels
available in your area.
• It may take from 15 minutes to 30 minutes to
complete memorizing digital cable channels.
Depending on the reception condition, a bar
display may not advance for several minutes,
please be patient.
NOTE:
• Memorizing channels is best accomplished during
evening "PRIMETIME" hours, as more stations are
broadcasting digital signals. Memorizing channels
can only be accomplished while a station is
broadcasting a digital signal to set that channel into
memory.
• If you are unsure of the digital channels available
in your area, you may visit www.antennaweb.org to
receive a list based on your address or zip code.
Should you require further assistance you may call
our toll-free customer service line at 1-800-289-0980.
• New digital channels may be added to your area
periodically, it is recommended to perform the
"Automatic Search" procedure regularly.
Adding Channel
If you find a new channel unregistered, you can add
the new channel into the channel memory.
1
Tune in the new channel.
2
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
16
3
Press ▲ or ▼ to select "Channel", then press ▶ or
ENTER.
4
Press ▲ or ▼ to select "Add/Delete", then press ▶
or ENTER.
Add/Delete
Adding Channel >>
Add/Delete >>

Clear All

>>
5 : Select ENTER:Set
Press ▲ or ▼ to select "Adding Channel", then
press ▶ or ENTER. The new channel will be
added into the channel memory.
6
Press EXIT/CANCEL to return to the normal
screen.
Add/Delete channel
You can select the channel that you want to skip.
1
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
2
Press ▲ or ▼ to select "Channel", then press ▶ or
ENTER.
3
Press ▲ or ▼ to select "Add/Delete", then press
▶ or ENTER.
4
Press ▲ or ▼ to select "Add/Delete", then press
▶ or ENTER.
5
Press ▲ or ▼ to select the channel that you want
to skip.
Add/Delete
CH Signal
2 Analog Add
3 Analog Add
3-001 Digital Delete
3-002 Digital Add
4 Analog Delete
6 : Select : Adjust
Press ◀ or ▶ to select "Add" or "Delete",
whichever function you want to perform.
7
Repeat steps 5 - 6 for other channels you want to
add or delete.
8
Press EXIT/CANCEL to return to the normal
screen.
Clear All
All channels are deleted from the channel memory.
1
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
2
Press ▲ or ▼ to select "Channel", then press ▶ or
ENTER.
3
Press ▲ or ▼ to select "Add/Delete", then press ▶
or ENTER.
4
Press ▲ or ▼ to select "Clear All", then press ▶ or
ENTER.
Add/Delete
Adding Channel >>
Add/Delete >>
Clear All >>
: Select ENTER:Set