1. Manuals
  2. Brands
  3. Tannoy Manuals
  4. Speakers
  5. System 1000
  6. User manual

Tannoy System 1000 User Manual

Monitor loudspeaker
Hide thumbs Also See for System 1000:
Table of Contents

Advertisement

Quick Links

REFERENCE MONITORS
SYSTEM 1000
USER MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Tannoy System 1000

Summary of Contents for Tannoy System 1000

  • Page 1 REFERENCE MONITORS SYSTEM 1000 USER MANUAL...

  • Page 2: Unpacking And Visual Checks

    95 dB for 8 hours per day will eventually cause permanent hearing loss. Because Tannoy Monitors have very low levels of time, amplitude and frequency distortion it is not always obvious that the sound level is high while working with them.

  • Page 3: Connecting The Loudspeakers

    We recommend location of the monitors so that the drive units are toed inwards, with their axes oriented towards the listening position. The distance between the two speakers should be 1.5 to 2.5 metres, depending on the monitoring position. The distance between the monitoring position and each speaker should be slightly greater than the distance between the speakers.

  • Page 4: Power Amplifiers

    Because of the high peak power handling of the Tannoy monitors, responsible use of even more powerful amplifiers should not represent a danger for the speakers if the amplifiers are not overdriven.
  • Page 5 (as in monitoring situations). The set of parameters that are arrived at as a solution are inevitably a compromise and the skill of Tannoy has always been shown to be getting these particular parameters correct for the application.

  • Page 6: Cabinet Finish

    The surface will change colour when wet but will return to normal when dry. For touch-up of paint chips contact your local Tannoy service agent for materials and guidance.

  • Page 7: Checking The Unit

    Crossover. The crossover is mounted on the internal vertical brace, behind the terminal panel. To inspect it, first remove the panel by releasing the hexagonal screws. Take care to avoid undue stress on the cables and components. To remove the crossover completely the cables must be disconnected from the drive unit.
  • Page 8 DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION. This warranty in no way affects your statutory rights. CURVES Figure 1. On axis anechoic response.

  • Page 9: Technical Specifications

    Figure 2. Impedance. TECHNICAL SPECIFICATIONS System Frequency response (1) 45 Hz - 20 kHz Recommended amplifier power 60 to 200 W rms into 8 Power handling Average (2) Programme 100 W rms 200 W rms Nominal Impedance Sensitivity (3) 94 dB SPL / 1 W @ 1 m Distortion <...
  • Page 10 Tannoy operate a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications which Tannoy reserve the right to alter without prior notice. Please verify the latest specifications when dealing with critical applications.

  • Page 11: Declaration Of Conformity

    Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is...
  • Page 12 For Tannoy Ltd...
  • Page 13 TGI/Tannoy, 300 Gage Avenue, Kitchener, Ontario, CANADA, N2M 2C8 Telephone: (519) 745 1158 Fax: (519) 745 2364 Tannoy Nederland BV, Anthonetta Kuijlstraat 19, 3066 GS, Rotterdam THE NETHERLANDS Telephone: (010) 2860554 Fax: (010) 2860431 Tannoy is a member of the Group of Companies Issue 2 Part No.

Table of Contents