Advertisement
6.0: TECHNICAL SPECIFICATIONS
PRECISION 6
LOUDSPEAKER
Frequency response
62Hz - 51kHz
(1)
Recommended amplifier power
60 to 120 W rms into 8Ω
Power handling
Average
60 W rms
(2)
Programme 120 W
Nominal Impedance
6Ω
Sensitivity SPL / 1 W @ 1 m
91 dB
(3)
Distortion
< 0.7%
Crossover frequency
2.5kHz
Dispersion (@ -6dB)
90 degrees
Dual Concentric™ LF/MID
165mm (6") Dual Concentric™ constant directivity
driver with multi fibre paper pulp cone
Dual Concentric™ HF
25mm (1") titanium dome neodymium magnet
system
WideBand™ HF
25mm (1") titanium dome neodymium magnet
system
Shielded
Yes
CABINET
Low frequency design
Optimised bass-reflex loaded
Cabinet construction
MDF cabinet and front baffle, Tongue and groove
front and back
Cabinet finish
Black cabinet Grey painted baffle with brushed
aluminium inlay
Fittings
4 x M6 inserts for Omnimount™ 30 series bracketry
Cabinet dimensions (HxWxD)
356mm x 220mm x 260.5mm
14" x 8
5
/
" x 10
8
Total Cabinet weight
8.9kg (19.6lbs)
NOTES
(1) +/- 3 dB, measured at 1m in an anechoic chamber. (2) Long term power handling capacity as defined in EIA standard RS426A.
(3) Averaged over specified bandwidth for half-space environment.
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications which Tannoy reserve the right to alter without
prior notice. Please verify the latest specifications when dealing with critical applications.
7.0: SERVICING
7.1: CABINET FINISH
To remove marks and scuffs use a soft brush. If necessary, a little warm water and detergent can be used but under no circumstances use a
solvent or abrasive cleaner.
7.2: DRIVER REMOVAL
Lay the cabinet on its back. Remove the ten hexagonal screws and set aside. Ease the driver from the front of the cabinet taking care not to
mark the front surface. Remove the driver, note the polarity of the internal connections and disconnect the internal wiring. Take care not to
damage the moving parts of the LF driver. To refit the driver, connect the cables from the crossover to the LF terminals. Fit the driver into the
mounting hole, making sure that the internal connecting cables are not trapped or able to touch the LF cone. Fasten the screws finger tight and
then progressively tighten them down with the appropriate Allen key.
Repeat the same procedure for the HF driver.
6
PRECISION 8
54Hz – 51kHz
80 to 160 W rms into 8Ω
Average
60 W rms
(2)
Programme 160 W
6Ω
93dB
< 0.5%
2.2kHz
90 degrees
200mm (8") Dual Concentric™ constant directivity
driver with multi fibre paper pulp cone
25mm (1") titanium dome neodymium magnet
system
25mm (1") titanium dome neodymium magnet
system
Yes
Optimised bass-reflex loaded
MDF cabinet and front baffle, Tongue and groove
front and back
Black cabinet Grey painted baffle with brushed
aluminium inlay
4 x M6 inserts for Omnimount™ 30 series bracketry
440mm x 272mm x 287.5mm
1
/
"
17
3
/
" x 10
3
/
" x 11
3
/
"
4
8
4
8
12.7kg (28lbs)
7.3: CROSSOVER
The crossover is mounted on the rear of the terminal panel. To inspect it, remove the panel by releasing the hexagonal screws. Take care to
avoid undue stress on the cables and components.
To remove the crossover completely the cables must be disconnected from the drive unit. Please proceed as above to remove the drive unit.
7.4: LIST OF SPARE PARTS
DESCRIPTION
PRECISION 6 (Part No)
Driver Kit
Type 1603 -7900 0747
High Frequency Unit
Type 0294 – 7900 0891B
Passive Crossover
Type 1464 – 7300 0937
8.0: WARRANTY
NO MAINTENANCE OF THE PRECISION MONITORS IS NECESSARY.
All components are guaranteed for a period of five years from the date of manufacture, subject to the absence of, or evidence of, misuse,
overload or accidental damage.
For further information please contact your dealer or the distributor in your country.
If you cannot locate your distributor please contact:
Customer Services, Tannoy Ltd., Coatbridge, Strathclyde, ML5 4TF, Scotland
Telephone: 01236 420199 (UK) +44 1236 420199 (International)
Fax: 01236 428230 (UK) +44 1236 428230 (International)
Internet: http://www.tannoy.com
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
This warranty in no way affects your statutory rights.
9.0: DECLARATION OF CONFORMITY
The following apparatus is/are manufactured in China for Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s)
to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment.
The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and
telecommunications equipment and other apparatus to operate as intended, and, the apparatus has an adequate level of intrinsic immunity to
electromagnetic disturbance to enable operation as specified and intended.
This equipment conforms to the requirements of the EMC Directive 89/336/EEC, amended by 92/31/EEC and 93/68/EEC and the requirements
of the Low Voltage Directive 73/23/EEC, amended by 93/68/EEC.
Details of the Apparatus:
Tannoy Monitor Loudspeaker
Model Number: Precision 6
Model Number. Precision 8
Applicable Standards:
EN55103-1:1996 Emission
EN55103-2:1996 Immunity
Electrical Safety EN60065:1993
Signed:
Position:
Technical Director
Date:
1 March 2005
For Tannoy Ltd
PRECISION 8 (Part No)
Type 1603 -7900 0747
Type 0294 – 7900 0891B
Type 1465 – 7300 0938
7
Advertisement
