Do you have a question about the SKYFi and is the answer not in the manual?
Questions and answers
Audrey Belyea
February 10, 2025
Delphi remote and where to change battery
1 comments:
Mr. Anderson
February 11, 2025
To change the battery in a Delphi SKYFi remote, slide the battery door off the back of the remote control, press down on the battery, and slide it out. Replace it with a 3V CR2032 lithium battery, ensuring the positive end faces the battery door, then replace the battery door.
Page 1
SKYFi ™ Operating Guide R a d i o t o t h e p o w e r o f X ™ Warning: This manual and the SKYFi Installation Guide contain important safety and operating information. Please read and follow the instructions in these manuals.
Page 3
Welcome Thank you for purchasing a SKYFi™ Receiver by Delphi. Your SKYFi Receiver gives you access to over 100 XM ® Satellite Radio chan- nels of music, news, and information. Your SKYFi Receiver must be used with a SKYFi adaptor kit, such as the SKYFi Home Kit or SKYFi Vehicle Kit.
Getting Started: Activating SKYFi 2. Press the power button to turn the SKYFi 4. Activate your XM Satellite Radio service. Receiver on and verify that it is playing To subscribe, make sure you have a major To quickly begin enjoying XM Satellite Radio, Channel 1, the XM Preview Channel.
Page 6
Category search Scroll wheel Enter button Control keys Power button Number keys Figure 1. SKYFi Receiver.
SKYFi Receiver Press menu to select and change Use the scroll wheel to scroll through receiver configuration options. and select a channel or a menu option. SKYFi Receiver controls The SKYFi unit has eight control buttons, Switches between DIRECT entry, Number keys are used to select a a scroll wheel, and 10 number keys.
SKYFi Receiver display screen Keypad mode (DIRECT, Preset A, or Preset B) While tuned to an XM channel, the SKYFi Signal strength indicator default display contains information (zero to three bars) about that channel and the SKYFi settings. See figure 2. Your SKYFi display can be customized.
SKYFi Remote Control Number keys are used to select a channel directly (when in DIRECT entry mode) by entering its number. Select Turns the SKYFi Receiver on and off. presets (when in Preset A or Preset B Enters category search and steps mode) by entering the number of the through available categories.
Basic Operations Basic channel selection Select a channel by number 1. Verify that SKYFi is in DIRECT entry mode. SKYFi allows you to select a channel by directly Turning SKYFi on and off DIRECT should appear in the upper right entering its number, using a preset key, or by Press on the SKYFi Receiver or SKYFi...
Page 11
Set/select channel presets Selecting channel presets Tune to a channel Your SKYFi Receiver can store up to 20 preset Press until an A or B appears in the upper Tune up and down the channel list using channels. They are organized into two differ- right corner of the display.
Page 12
Preview and select a channel based 4. Select a channel with . If you do not Preview favorite channels on channel name or the current select a channel, the display will time out and You can use the preset keys and category song or artist return to the channel you are listening to.
3. Press to display the channel name, Enlarging display text Save and recall artist name and song title artist name, or song title for each preset. Your SKYFi display can be reconfigured to be You can save the artist name and song title on 4.
Menu Commands and Settings Memory Recall Line Out Level This is an alternative way of entering memory Use this to adjust the SKYFi Receiver audio- Pressing enters the menu section of recall mode. It functions the same as pressing level output if it is too high, causing distortion, SKYFi.
Page 15
Auto Shutdown Antenna Aiming Factory Default You can set your radio to automatically shut You can optimize the position of your home Selecting this option restores all of the set- off 60, 120, or 180 minutes after it is turned on. antenna, as described in the SKYFi Installation tings to their original factory setting.
Reference Replacing SKYFi Remote Control batteries Taking care of your SKYFi Your SKYFi Remote Control uses a 3V CR2032 (Failure to follow these instructions may Lithium battery, available at most retailers that result in personal injury or damage to your carry electronic products.
Technical information Dimensions SKYFi Receiver· · · · · · · · · · · · · · · · · 4.65 in W x 2.91 in H x 1.26 in D (118 mm x 74 mm x 32 mm) SKYFi Remote Control ·...
Troubleshooting • Make sure the adaptor is firmly seated If you see this on the display: You should: in the cigarette lighter/auxiliary power Your SKYFi Receiver is designed and built NO SIGNAL If you are using SKYFi at socket. Cause: The XM signal is out home, reposition the antenna.
Contact XM as described in “Getting Started: Activating For additional information in solving problems with 0 and 1 SKYFi” on page 2. your SKYFi Receiver, contact Delphi at 1.877.GO DELPHI Cause: Your SKYFi Receiver is not activated. (1.877.463.3574) Monday – Friday, 8:00 am – 4:30 pm Eastern Standard Time, or visit www.delphi.com.
Portable XM Satellite Radio Limited The duration of Delphi’s warranty with respect Delphi will, as its sole obligation under this Consumer Warranty to Delphi Portable XM Satellite Radio Products warranty, replace or repair, at its option, is limited to one (1) year from the date of sale...
(viii) normal wear and tear, (ix) commercial When contacting Delphi by fax, please How state law relates to the warranty: use, (x) service by anyone other than a Delphi include a letter detailing your complaint and Some states do not allow limitations on how...
Page 22
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Delphi could void the user’s authority to operate this equipment.
Need help?
Do you have a question about the SKYFi and is the answer not in the manual?
Questions and answers
Delphi remote and where to change battery
To change the battery in a Delphi SKYFi remote, slide the battery door off the back of the remote control, press down on the battery, and slide it out. Replace it with a 3V CR2032 lithium battery, ensuring the positive end faces the battery door, then replace the battery door.
This answer is automatically generated