Making An Audio Cd - Fostex VF08 Supplement Owner's Manual

The following procedure describes how to record mastered songs (using the internal mastering function) to a CD-
RW/CD-R disc to make an audio CD (CD-DA format).
The "Save PGM" menu in the Setup mode, which is used for saving song data, is also used for making an audio CD.
VF08
INPUT A ST OUT FOOT SW
INPUT B PHONES
BAL BAL L R
MIX PARAMETER
TRACK
EDIT SCENE SCENE SEQ.
GUITAR GUITAR
DIGITAL MULTITRACKER
PGM FADER MAP
PAN EQ EFFECT
LINE MIC LINE MIC MIN MAX
UNBAL TRIM UNBAL TRIM
ON/OFF
ACCESS
BOUNCE MODE 2TRK MODE
CH ON/OFF CH ON/OFF MASTERING TRAINING
PEAK PEAK
PHANTOM
F1 F2 F3
TRACK STATUS RED
REC GREEN PLAY OFF MUTE STATUS
TRACK STATUS / TRACK SEL /SEL
JOG
1 2 3 4 5 6 7/8 2TRK MASTER CURSOR
EXIT
/NO
EJECT
+6 +6 +6 +6 +6 +6 +6 +6
ENTER
/YES
0 0 0 0 0 0 0 0
TIMEBASE UNDO
SETUP SEL /REDO
-10 -10 -10 -10 -10 -10
-10 -10 F1 F2 F3 SHIFT
AUTO VARI WAVE FORM LOCATE
-20 -20 -20 -20 -20 -20 -20 -20 PUNCH LOOP PITCH SCRUB
-30 -30
-30 -30 -30 -30 -30 -30
EDIT EDIT EDIT MARK
-40 -40 -40 -40 -40 -40 -40 -40
RECORD STOP PLAY REWIND
- - - - - - - -
LOCATE ABS 0
LOCATE REC END
Start point End point
Start point
1
Silence (about 2 seconds)
In the following procedure, we assume that one or
more mastering programs exist and a CD-RW drive is
connected to the SCSI port of the Model 8340 installed
in the VF08 and a non-recorded CD-RW/CD-R disc is
used.
<Note>
Key operations of the VF08 should be done after
completing access to a CD-RW/CD-R disc.
1. After turning on the power of both the VF08 and a
connected CD-RW drive, load a non-recorded disc to the
CD-RW drive.
2. Press the [SETUP] key to enter the Setup mode.
3. Use the [JOG] dial to select (highlight) the "Save PGM"
menu and press the [ENTER/YES] key.
The display shows the screen for selecting the device to
which the data is saved. "SCSI" flashes.

Making an audio CD

CD-RW/CD-R disc
SHUTTLE
DELETE
F FWD
<Figure-1>
Start point
End point
2 3
<Figure-2>
flashing
<Basic information>
When making an audio CD using the VF08, inter-
nal mastering materials on the current drive are
recorded to a CD-RW/CD-R disc (by the CD-DA for-
mat).
As we explain in "Save/load of Song Data using a
CD-RW drive" on page 9, you can record not only a
single song but also multiple songs continuously.
When recording more that one songs continuously,
the VF08 automatically inserts a 2-second silent
space between songs.
<Note>
End point
If an audio CD is made using a CD-RW disc, it
can be played back only by a player that sup-
ports CD-RW playback. You cannot playback such
a disc by a conventional CD player that does not
support CD-RW playback.
4. Press the [ENTER/YES] key while "SCSI" flashes.
After showing the model name of the connected CD-RW
drive, the display shows the screen for selecting the save
mode, in which "BkUp" flashes.
To carry out making an audio CD, select "CD-DA".
If you need to change the copy protection setting (the
default setting is "OFF"), select "Setup" (for setting
writing conditions). If you make an audio CD without
changing the copy protection setting, skip steps 5 and 6
below and go to step 7.
flashing
5. Use the [JOG] dial (or the [CURSOR] < > key) to select
"Setup" and press the [ENTER/YES] key.
The display shows the "CD-DA Setup" screen, on which
you can select the copy protection setting (see the next
page).
14