Recording An Analog Source; 6.1 Ch Input - Marantz SR5400 User Manual

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source
selected for listening through the SR5400 is sent to
the record outputs.
This means that any program you are watching or
listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD-R/MD OUT, VCR1 OUT, and DSS/VCR2 OUT
in the record mode.
To record the input source signal you are currently
watching or listening to
1.
POWER
OUND RECEIVER SR5400
TV VCR1 DSS/VCR2
1.
TUNER CD TAPE
CLEAR MEMORY TUNING F/P MODE
VIDEO OFF 6.1CH INPUT A/D S-DIRECT DISPLAY
NTER
AUX AMP
TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD TUNER
TV
HONES VOL. SLEEP MUTE
OSD MENU
1.
Select the input source to record by pressing
the corresponding input selector button.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to the TAPE OUT , CD-R/MD OUT,
VCR1 OUT, and DSS/VCR2 OUT outputs for
recording.
3.
Start recording to the recording component as
desired.
Recording the video from one source and the
audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from a
compact disc player connected to CD IN and the
video from a video camera connected to AUX IN to
video cassette recorder connected to the VCR1
OUT jack.
1. 2.
400
2.
CLEAR MEMORY TUNING F/P MODE
1.
VIDEO OFF 6.1CH INPUT A/D S-DIRECT DISPLAY
DVD
TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD TUNER
CDR/MD
MAIN
VOL.
1.
Press the AUX input source button to set
video output.
2.
Press the CD input source button to set audio
output.
3.
Now "CD" has been selected as the audio
input source and "AUX" as the video input
source.
Notes:
• If you change the input source during recording,
you will record the signals from the newly
selected input source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog .
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.

6.1 CH INPUT.

The SR5400 is equipped for future expansion
t h r o u g h t h e u s e o f M u l t i c h a n n e l S A C D
multichannel player or DVD-Audio player.
When this is selected, the input signals connected
to the L(front left), R (front right), CENTER, SL
(surround left), SR (surround right) and SB
(surround back) channels of the 6.1 CH. In jacks
are output directly to the front (left and right),
center, surround (left and right) and surround back
speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
TV VCR1 DSS/VCR2 DVD
jack is output to the PRE OUT SW (subwoofer)
TUNER CD TAPE CDR/MD
jack.
When 6.1 CH. INPUT is selected, the last video
AUX AMP
TV MAIN
input used remains routed to the Monitor Outputs.
VOL. SLEEP MUTE VOL.
This permits simultaneous viewing with video
sources.
OSD MENU
2.
V SURROUND RECEIVER SR5400
CLEAR MEMORY TUNING F/P
VIDEO OFF 6.1CH INPUT A/D S-DIRECT
ENTER
TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE
PHONES
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs .
2.
Press the 6.1 CH INPUT button on the front
panel or press 6.1 CH IN on the remote to
switch the 6.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, use "6.1 Ch. INPUT LEVEL" in
the OSD menu system as desired.
Adjust the speaker output levels so that you
can hear the same sound level from each
speaker at the listening position. For the front
left, front right, center, surround left, surround
right and surround back speakers, the output
levels can be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 6.1
Ch. INPUT memory. (see to page 19)
4.
Adjust the main volume with the MAIN VOLUME
knob or the VOL buttons on the remote.
To cancel the 6.1 Ch. INPUT setting, press the 6.1
CH INPUT button on the front panel or press 6.1
CH IN on the remote.
Notes:
• When the 6.1 Ch. Input is in use, you may not
select a surround mode, as the external decoder
determines processing.
• In addition, there is no signal at the record outputs
when the 6.1 Ch. Input is in use.
SETUP/ MENU OFF
T.TONE
S-DIRECT AUTO DTS
1 2 3
NIGHT CSII EX/ES DSP
4 5 6
2.
DISPLAY M-CH ST STEREO 6.1CH IN
7 8 9
CLEAR MEMO A/D P.SCAN
0
CHANNEL/SKIP
BASS TREBLE TUNE/SEARCH
MODE DISP./RDS F.DIRECT
/A /ANT /B /VCR ATT PTY
25