On/Off Switch; Default Program; Temperature Override; Weekday Programming - Lux Products WIN100 series Installation And Operating Instructions Manual

HEAT
Use HEAT mode to warm your home with a Space
●
Heater.
In HEAT mode, HEAT is displayed right of the set
●
temperature.
COOL
●
Use COOL mode to control your Window Air
Conditioner, cooling your home.
In COOL mode, COOL is displayed right of the set
●
temperature.

ON/OFF SWITCH

Slide the SLIDE switch to OFF when no heating or
cooling is desired. Heating and cooling will be disabled,
even though the set temperature, room temperature,
and time will still be in the display.

DEFAULT PROGRAM

As supplied from the factory, your thermostat will use
its default ENERGY STAR
perature control. This program and all other settings
may be restored to their default values via a SOFTWARE
RESET. Please refer to DEFAULT TEMPERATURE PRO-
GRAM for program times and temperatures.
HOLD
Hold is the simplest method to maintain fixed set tem-
peratures.
Press HOLD once to enter the temperature HOLD
●
while in RUN or OVERRIDE. HOLD will be displayed on
the bottom of the display.
●
Pressing this button again will toggle HOLD off and
return the unit to RUN and the programmed set temper-
ature.
●
Changing system mode or rotating the SPEED DIAL
will also cancel a HOLD.

TEMPERATURE OVERRIDE

●
OVERRIDE allows you to change the current SET
TEMPERATURE in HEAT of COOL until the next pro-
gram period without changing your temperature control
programs.
●
Press an arrow key once.
While the Set Temperature is flashing; press an UP or
●
DOWN key to adjust the set temperature by one degree
in the associated direction. Holding the key will auto-
matically advance the setting in the associated direction.
●
The OVERRIDE will be canceled at the start of the
next program period, and the temperature setting will
return to its programmed value.
●
An OVERRIDE may be terminated by rotating the dial,
switching the mode to OFF, or initiating a Hold.
●
Adjusting the set temperature to its program value will
also cancel an OVERRIDE.
® approved program for tem-
PROGRAMMING
EDITING HEAT OR COOL PROGRAMS
The WIN100 provides two separate programs, one for heat-
ing and the other for cooling. Each program has separate
settings for weekdays and weekends. Every day a program
cycles through four independent periods. You can use the
default programs or alter them to suit your schedule.
DEFAULT TEMPERATURE PROGRAM
As supplied from the factory, the following ENERGY STAR
approved program will be used for temperature control in
RUN MODE. This program and all other software settings
may be restored to their default values via a SOFTWARE
RESET.
PERIOD
Morning 6:00 AM 70°F (21°C)
Day 8:00 AM 62°F (17°C)
Evening 6:00 PM 70°F (21°C)
Night 10:00 PM 62°F (17°C)

WEEKDAY PROGRAMMING

To change the HEAT or COOL program:
Set to HEAT if you are using a Space heater.
●
Set to COOL if you are using a Window Air
●
Conditioner
Rotate dial to SET WEEKDAY PROGRAMS.
●
MORN, Mo, Tu, We, Th, Fr will be displayed, with the
®
Start Time flashing.
Programming is performed in the following order.
1. Weekday Morn Start Time
2. Weekday Morn Set Temperature
3. Weekday Day Start Time
4. Weekday Day Set Temperature
5. Weekday Eve Start Time
6. Weekday Eve Set Temperature
7. Weekday Nite Start Time
8. Weekday Nite Set Temperature
9. . . . and so on until Fri Nite is fully programmed at
which point pressing NEXT again will begin the list at
Mo - Fri Morn Start Time.
Use the UP/DOWN keys to change the start time for
●
this period. Press UP/DOWN buttons to change the
time in 15-minute increments. Hold UP/DOWN button
to change the time at a faster rate.
HEAT MODE
6:00 AM 78°F (26°C)
8:00 AM 85°F (30°C)
6:00 PM 78°F (26°C)
10:00 PM 82°F (28°C)
®
COOL MODE