Advertisement
Quick Links
HIGH SPEED OVEN INSTALLATION INSTRUCTIONS
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
NOTE:
1. Base must be capable of supporting 200
pounds (90.7 kg).
2. Make sure base is level and front of cabinet
is square. If the cabinet base is not level, the
oven will tend to slide out when opening
the door.
3. Minimum required distance is 36" (91.44
cm) from the floor.
4. At the rear of the opening, provide a 3
pronged, polarized, electrical outlet, 240
volt A.C., 15 amp. or larger. This outlet
should not be located in the shaded area
of Figure 1. It is exceedingly important that
the outlet be 240 volts and 15 amps. for
optimum oven performance.
5. Minimum required distance between the
high speed oven and the wall oven should
be 3-inches.
MODEL
30" (76.2) High Speed
Oven
MODEL
30" (76.2) High Speed
Oven
All dimensions are in inches (cm).
Important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the high speed oven.
2. Remove all packing material from the oven compartments
before connecting the electrical supply to the high speed
oven. Remove the 2 shipping duct supports (see figure
1) by removing the 4 screws securing them. Reinsert 2
screws (each side) to secure the stainless cover.
Printed in United States
The electrical requirements for this oven are 240 volts, 15 amps.
The oven has a 6-15 plug and requires a 6-15 receptacle.
Remove 2 duct
shipping supports
(both sides)
PRODUCT DIMENSIONS
A
30" (76.2)
CUTOUT DIMENSIONS AND CABINET WIDTH
Min.
F
Max.
22
/
" (56.8) 22
/
" (57.5)
3
5
8
8
A
C
B
D
Replace these
screws after
shipping support
removal (both sides)
B
22
/
" (58.0)
27
32
G
Min.
24" (61.0) min.
21
/
"(55.1) 21
11
16
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
Important Note to the Consumer
Keep these instructions with your Owner's Guide for future
reference.
1
I
H
7
F
21
/
"
32
(53.9 cm)
Figure 1
C
21
/
" (54.0)
22
1
4
H
Max.
/
"(55.7)
30" (76.2) min.
15
16
G
1
20
/
"
4
C L
3
16
/
"
4
D
/
" (58.2)
15
16
I
TINSEB424MRR0
Advertisement
Related Manuals for Electrolux TINSEB424MRR0
Summary of Contents for Electrolux TINSEB424MRR0
-
Page 1: Important Notes To The Installer
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. The electrical requirements for this oven are 240 volts, 15 amps. The oven has a 6-15 plug and requires a 6-15 receptacle. NOTE: 1. -
Page 2: Important Safety
The oven side bracket will clip into the Anti-Tip brackets (see figure 2). 4. To pull out the oven for servicing insert the tool supplied with the appliance both side at the same time in the hole located on the side frame and visible when the door is opened. -
Page 3: Model And Serial Number Location
The serial plate is located on the oven faceplate. When ordering parts for or making inquires about your oven, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your oven. - Page 4 HIGH SPEED OVEN INSTALLATION INSTRUCTIONS NOTES...