Table of Contents
Advertisement
If you have any advice or requirements, please feedback or call 0755-86021373.
ATTEN INSTRUMENTS
RF Microwave Instruments
Therefore Microwave Components
Spectrum Analyzers
Regulated DC Power Supply
Regulated AC Power Supply
Switching DC Power Supply
Inverter DC Power Supply
Portable Power
Oscilloscope/ Signal Generator
Attenuator/ Amplifier
850 Rework Station
936 Constant Temp Soldering Station
Electronic Instruments
Electronic Tools
SHENZHEN ATTEN ELECTRONICS CO., LTD.
MFR Add: Building A29, Tanglang Industrial Zone, Xili,
Nanshan, Shenzhen, 518055, P. R. China
Tel: 0755-8602 1373 8602 1372
Fax: 86-755-8602 1337
http: //www.atten.com.cn
E-mail: atten@atten.com.cn
FRANCHISER
Thanks for using our products, please read this manual thoroughly before operation.
Users Manual
SHENZHEN ATTEN ELECTRONICS CO., LTD.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Atten AT6010
Summary of Contents for Atten AT6010
- Page 1 850 Rework Station 936 Constant Temp Soldering Station Electronic Instruments Electronic Tools Users Manual SHENZHEN ATTEN ELECTRONICS CO., LTD. MFR Add: Building A29, Tanglang Industrial Zone, Xili, Nanshan, Shenzhen, 518055, P. R. China Tel: 0755-8602 1373 8602 1372 Fax: 86-755-8602 1337 http: //www.atten.com.cn...
-
Page 2: Table Of Contents
(such as RF pulse signal) can be develop. Prior to third part testing. A near-field Mainly Performance and Calibration observed from ATTEN spectrum analyzer sniffer probe set, AZ530, can be used to locate clearly, where figures are expanded by... -
Page 3: Near Field Sniffer Probes Az530
Specifications Input/output The H-Field Near-Field probe Probe are all matched to the 50 inputs of Spectrum analyzers or RF-receivers. The Frequency range: 0.15~1050MHz Signal input: N connector The H-Field probe provides a voltage to the power can be supplied either from batteries, 10ppm/year Impedance: 50 Stability:... -
Page 4: Frequency Expander At5000F Series
RF Signal Generator for mobile phones has are all above several ten thousands RMB, it is analyzer. been researched by ATTEN, its frequency as not affordable for most radio fans, service men well as the output amplitude can be When connect mobile phone to RF signal and even medium or small sized enterprises. -
Page 5: Safety
Spectrum Analyzer (C). For the D position has been subject to severe transport stress factory in a safe condition. This instruction and care. ATTEN shall not be obliged to (10 inclination), the handle should be turned (e. g. in poor packaging). -
Page 6: Switching Over The Mains/Line Voltage
The spectrum analyzer works according to the Switching over the mains / line voltage Safety including the instructions prior to fuseholder is not permissible; ATTEN assumes triple superhet receiver principle. The signal to operating the AT6010/AT6011. No special no liability whatsoever for any damage caused be measured (fin = 0.15MHz to 1050MHz) is... -
Page 7: Control Elements
Due to the frequency conversion principle,a steps. As previously pointed out, the on the screen. It enables small level spectral (20) Output Info (AT6011 only) spectral line is visible at 0Hz. It is called maximum permissible input voltages may not lines to become visible which normally would FREQENCY: 1 to 1050MHz If-feedthrough. -
Page 8: Horizontal Calibration
Introduction to the operation of the input attenuators (14) can contains information not found in the time signals in the frequency range of the analyzer. be tested at a level of -27dBm. The spec-tral domain and therefore, the spectrum analyzer hence the name real-time. -
Page 9: Spectrum Analyzer Requirements
displayed. and displayed. When the frequency narrowest bandwidth that can be used to Frequency Measurements Resolution difference between the input signal and the LO distinguish a single input signal is 10kHz. Any frequency is equal to the IF frequency, then narrower IF-filter will result in more than one Before the frequency of a signal can be The frequency scale can be scanned in three... -
Page 10: Video Filtering
of two analyzers, to compare sensitivity by 3dB) because the signal power=average Dynamic range requires several things then. voltage from the LO is too large compared to specifications for equal bandwidths. A noise power. The display range must be adequate, no the input signal voltage then the conversion spectrum analyzer sweeps over a wide spurious or unidentified response can occur,... -
Page 11: Mainly Performance And Calibration
Mainly Performance configuration is use for making selective and measurement set-up, they are completely Gratitude. Sensitive precise measurement of frequency, eliminated from the CRT display. 6. Frequency Response and Calibration of by tuning to the signal and switching to zero It means signal response of spectrum analyzer scan.
Need help?
Do you have a question about the AT6010 and is the answer not in the manual?
Questions and answers