Table of Contents
Advertisement
Atten Instruments
Spectrum Analyzer Series
RF Signal Generator
High-Accuracy Regulated DC Power Supply
850 SMD Rework Station
936 Soldering Station
Frequency Counter
Telecommunication Tester
Coaxial Components & Waveguide Components
Microwave Amplifier, Filter
Franchiser
SHENZHEN ATTEN ELECTRONICS CO., LTD.
ADD: 5/F, BUILDING 123, JINDI INDUSTRIAL ZONE,
FUTIAN, SHENZHEN, 518048, P . R. CHINA
http: //www.atten.com.cn
E-mail: atten@atten.com.cn
AT5010/ 5011/ 5000
SHENZHEN ATTEN ELECTRONICS CO., LTD.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Atten AT5010
Summary of Contents for Atten AT5010
- Page 1 Frequency Counter Telecommunication Tester Coaxial Components & Waveguide Components Microwave Amplifier, Filter Franchiser SHENZHEN ATTEN ELECTRONICS CO., LTD. ADD: 5/F, BUILDING 123, JINDI INDUSTRIAL ZONE, FUTIAN, SHENZHEN, 518048, P . R. CHINA SHENZHEN ATTEN ELECTRONICS CO., LTD. http: //www.atten.com.cn E-mail: atten@atten.com.cn...
-
Page 2: Table Of Contents
(AT5010/5011/5000) Near Field Sniffer Probes AZ530 Frequency Expander AT5000F Series AT808 GSM Servicing RF Signal Generator Symbols Tilt handle Operating conditions Warranty Maintenance Switching over the mains/line voltage Operating Instructions Control Elements Vertical Calibration Horizontal Calibration Types of Spectrum Analyzers... - Page 3 AZ530-H AZ530-M AZ530-E...
-
Page 9: Specifications
RF circuit, IF signal and transmission signal, It is very quick and accurate to use AT5010 spectrum analyzer to overhaul the fault of mobile phone which can not enter the network, and determine the fault point. -
Page 10: Near Field Sniffer Probes Az530
It is easily noticed which relationships in the circuit with the probe. One can, Sensitivity: Better than -90dBm directly connected to an AT5010/AT5011 series compo-nent (i.e.IC)causes interference and which for example, measure the quantitative effectiveness Log scale fidelity: 2dB(without attn.) spectrum analyzer. -
Page 11: Symbols
D position and swing backwards allows anyone to quickly become familiar with the requirements for electrical equipment for mobile phones has been researched by ATTEN, its until if locks once more. The handle may also be set operation of the instrument, however, experienced measurement, control, and laboratory use. -
Page 12: Operating Conditions
Under posed on a dc voltage which allows for the control ATTEN warrants to its Customers that the products no circumstances may the cleaning fluid get into the of 1st LO. The spectrum analyzer scans a frequency it manufactures and sells will be free from defects in instrument. -
Page 13: Operating Instructions
DIV.) should be selected prior to any spectral to the bandwidth is 4KHz. When the switch is in the ON position, MK is lit AT5010/11 input. This permits the detection of any and the display shows the center frequency. The (12) Y-Position... -
Page 14: Vertical Calibration
-27dBm, and it will reduce 10dBm for Prior to calibration ensure that all input attenuator (18) Phone switches (14) are released. The AT5010/11 must be each division drop. If the 40dB attenuator in the (3.5mm earphone connector) operated for at least 60 minutes prior to calibration. -
Page 15: Types Of Spectrum Analyzers
Introduction to dynamic range of the spectrum analyzer is useful sensitivity. Because trf analyzers have a swept filter Spectrum Analyzer Requirements for measuring low-level modulation. It can be used they are limited in sweep width depending on the Spectrum Analysis to measure AM, FM and pulsed RF. -
Page 16: Resolution
Last, the display system. This system noise which is measured on the circuit. This is (for the AT5010/11) +10dB for the The resolution of the spectrum analyzer is limited range must be adequate. -
Page 17: Frequency Response
The tracking generator (AT5010 only) is a special the analyzer passband, and all generator harmonics, generator: connect output port with frequency signal source whose RF output frequency tracks...
Need help?
Do you have a question about the AT5010 and is the answer not in the manual?
Questions and answers