Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG Electrolux B 99852G
Summary of Contents for AEG Electrolux B 99852G
- Page 1 B 99852G User Manual...
-
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. - Page 3 Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage.
-
Page 4: Table Of Contents
Contents Instructions for the User Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working? Service and Spare Parts Customer Care Guarantee Conditions Instructions for the Installer Important safety requirements Installation Building In Electrical connections Wiring diagram Fault Finding Commissioning Conversion from Natural Gas to LPG... -
Page 5: Description Of The Hob
Description of the Hob Hob Top Semi-rapid Burners Auxiliary Burner Ultra-rapid Burner (triple crown) Control knobs INSTALLATION Any gas installation must be carried out by a competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. -
Page 6: Operation
Operation Hob burners To light a burner: Push in the relevant control knob and turn it to maximum position. Upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (fig. 1 - letter D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. -
Page 7: Maintenance And Cleaning
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water... -
Page 8: The Burners
Pan Supports To keep the pan supports in the correct position, they are mounted on metal pins located in the back of the hob. After cleaning the hob, ensure the pan supports are properly placed as shown in fig. 3. The pan supports are dishwasher proof. -
Page 9: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM There is no spark when lighting the gas The gas ring burns unevenly If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. -
Page 10: Service And Spare Parts
5. Date of purchase Customer Care For general enquiries concerning your AEG-Electrolux appliance and for further information on AEG-Electrolux products, contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk Customer Care Department... -
Page 11: Guarantee Conditions
Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: •... -
Page 12: Instructions For The Installer
Instructions for the Installer Engineers technical data Overall dimensions Width: Depth: Cut out dimensions Width: Depth: Supply Connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. -
Page 13: Important Safety Requirements
Instructions for the Installer Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations. -
Page 14: Installation
Installation Important This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. -
Page 15: Building In
Instructions for the Installer Cut Out Size The dimensions of the cut-out are given in the diagram. FO 2349 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. -
Page 16: Building Over A Kitchen Unit With Door
ON/OFF SWITCH FLEX OUTLET FO 0763 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram The panel fitted under the hob ("a") should be easily removable to allow easy access... -
Page 17: Fitting The Hob To The Worktop
Instructions for the Installer Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. -
Page 18: Electrical Connections
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply. -
Page 19: Wiring Diagram
Instructions for the Installer Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. -
Page 20: Fault Finding
Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation check. Rectify any fault including replacing fuses as necessary. Carry out: Carry out: D: Resistance to... - Page 21 Instructions for the Installer A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω...
- Page 22 Ignition System / Gas Ignition Ignitor does not spark Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the...
-
Page 23: Commissioning
Instructions for the Installer Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 24: Conversion From Natural Gas To Lpg
Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit. - Page 28 www.aeg-electrolux.co.uk...