WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice.
The suitability of this product for other PC or embedded non-PC applications or other environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported without further evaluation by Intel. Document Organization The chapters in this Product Guide are arranged as follows:...
Intel Desktop Board DQ965CO Product Guide Terminology The table below gives descriptions of some common terms used in the product guide. Term Description Gigabyte (1,073,741,824 bytes) Gigahertz (one billion hertz) Kilobyte (1024 bytes) Megabyte (1,048,576 bytes) Mbit Megabit (1,048,576 bits)
Processor ......................13 Main Memory ...................... 13 ® Intel Q965 Express Chipset................. 15 Intel Q965 Graphics Subsystem..............15 GMA 3000 Graphics Controller ............... 15 Digital Video Interface (DVI)..............16 Onboard Audio Subsystem ................... 17 Input/Output (I/O) Controller ................17 LAN Subsystem....................18 LAN Subsystem Software................
Page 6
Configuring the BIOS for Intel Matrix Storage Technology......... 69 SATA Port Mapping ..................69 Creating Your RAID Set ................70 Loading the Intel Matrix Storage Technology RAID Drivers and Software .... 71 Setting Up a “RAID Ready” System ..............71...
Page 7
30. Location of the BIOS Configuration Jumper Block..........56 31. Back Panel Connectors ................... 59 32. Removing the Battery ..................64 33. Original SATA Port Mapping for Desktop Board DQ965CO ........69 34. SATA Port Mapping for Desktop Board DQ965CO After RAID is Enabled ....70...
Page 8
3. DVI/VGA Port Status ..................16 4. LAN Connector LED States ................18 5. Front Panel Audio Header Signal Names for Intel High Definition Audio....48 6. AC ’97 Audio Header Signal Names ..............48 7. USB 2.0 Header Signal Names................. 49 8.
1 Desktop Board Features This chapter briefly describes the main features of Intel Desktop Board DQ965CO. ® Table 1 summarizes the major features of the desktop board. Table 1. Feature Summary microBTX (264.16 millimeters [10.40 inches] x 266.70 millimeters Form Factor [10.50 inches])
• Remote diode temperature sensing • Voltage sensing to detect out of range values Related Links: For more information about Desktop Board DQ965CO, including the Technical Product Specification (TPS), BIOS updates, and device drivers, go to: http://support.intel.com/support/motherboards/desktop/ Supported Operating Systems The desktop board supports the following operating systems: •...
Desktop Board Features Desktop Board Components Figure 1 shows the approximate location of the major components on Desktop Board DQ965CO. Figure 1. Desktop Board DQ965CO Components...
NOTE ® The Intel Management Engine in the chipset requires memory to be populated in Channel A, DIMM 0 in order for it to enable Intel Quiet System Technology and Intel Active Management Technology.
Page 14
Up to 4.0 GB utilizing 512 Mb or 1 Gb technology • Up to 8.0 GB utilizing 1 Gb technology NOTE 1 Gb memory technology is not supported on DDR2-800 DIMMs. Intel recommends using memory from the tested memory lists, available at: http://www.cmtlabs.com/mbsearch.asp http://www.intel.com/products/motherboard/index.htm?iid=HMPAGE+Header_2_Pro duct_MB Related Links: Go to the following links or pages for more information about: •...
Advanced Digital Display 2 card or Media Expansion Card (ADD2/MEC) support • Dynamic Video Memory Technology support • Digital Video Interface (DVI-D) NOTE A minimum of 512 MB of system memory is required in order for the Intel GMA 3000 integrated graphics controller to operate properly.
Intel Desktop Board DQ965CO Product Guide Digital Video Interface (DVI) The DVI port supports only DVI-D (digital only) displays. The maximum support resolution is 1600 x 1200 at 60 Hz refresh rate. The DVI port is compliant with the following specifications: •...
Desktop Board Features Onboard Audio Subsystem Desktop Board DQ965CO has a flexible 6-channel (5.1) onboard audio subsystem that includes a SigmaTel STAC9227 audio codec and an HD Audio Link header. The audio subsystem features: • Intel High Definition Audio interface •...
VT partitions • RJ-45 connector with status indicator LEDs LAN Subsystem Software For LAN software and drivers, refer to the DQ965CO link on Intel’s World Wide Web site at: http://support.intel.com/support/motherboards/desktop RJ-45 LAN Connector LEDs Two LEDs are built into the RJ-45 LAN connector located on the back panel (see Figure 2).
• System Defense Feature - an Intel AMT feature for stopping the propagation of worms and viruses through the use of programmable packet filters in the integrated LAN controller. The packet filters inspect all incoming and all outgoing packets and determine whether to block or pass the packets as configured.
Intel Desktop Board DQ965CO Product Guide Hi-Speed USB 2.0 Support NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable.
Desktop Board Features BIOS The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI/PCI Express and IDE auto-configuration utilities, and the video BIOS. The BIOS is stored in a Serial Peripheral Interface (SPI) Flash device. The BIOS can be updated by following the instructions on page 65 in Chapter 3. Serial ATA and IDE Auto Configuration If you install a Serial ATA or IDE device (such as a hard drive) in your computer, the auto-configuration utility in the BIOS automatically detects and configures the device...
• Intel Quiet System Technology, delivering acoustically-optimized thermal management NOTE Memory must be installed in the Channel A, DIMM 0 socket to enable Intel® Quiet System Technology. • Fan speed controllers and sensors integrated into the ICH8 • Thermal sensors in the processor, GMCH, and ICH8 plus an onboard remote sensor •...
Desktop Board Features Power Management Features Power management is implemented at several levels, including: • Software support through the Advanced Configuration and Power Interface (ACPI) • Hardware support: ― Power connectors ― Fan headers ― LAN wake capabilities ― Instantly Available PC technology (Suspend to RAM) ―...
Wake from LAN is disabled by default in the BIOS for power saving. Wake from S5 must be enabled in the BIOS in order for Intel AMT Out of Band management to function. Instantly Available PC Technology...
Figure 3. Location of the On-board Power Indicators Related Links: For more information on standby current requirements for the desktop board, refer to the Technical Product Specification by going to the following link, finding the product, and selecting Product Documentation from the left-hand menu: http://support.intel.com/support/motherboards/desktop/...
Intel Desktop Board DQ965CO Product Guide Wake from USB NOTE Wake from USB requires the use of a USB peripheral that supports Wake from USB. USB bus activity wakes the computer from an ACPI S3 state. Wake from PS/2 Keyboard/Mouse PS/2 keyboard/mouse activity wakes the computer from an ACPI S3 state.
2 Installing and Replacing Desktop Board Components This chapter tells you how to: • Install the I/O shield • Install and remove the desktop board • Install and remove a processor • Install and remove memory • Install and remove a PCI Express x16 card •...
Intel Desktop Board DQ965CO Product Guide Installation Precautions When you install and test the Intel desktop board, observe all warnings and cautions in the installation instructions. To avoid injury, be careful of: • Sharp pins on connectors • Sharp pins on printed circuit assemblies •...
Installing and Replacing Desktop Board Components Installing the I/O Shield The desktop board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Install the I/O shield before installing the desktop board in the chassis.
Intel Desktop Board DQ965CO Product Guide Installing and Removing the Desktop Board CAUTION Only qualified technical personnel should do this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage.
Intel Desktop Board DQ965CO Product Guide Installing and Removing a Processor Instructions on how to install the processor on the desktop board are given below. Installing a Processor CAUTION Before installing or removing the processor, make sure the AC power has been removed by unplugging the power cord from the computer;...
Installing and Replacing Desktop Board Components 4. Remove the plastic protective socket cover from the load plate (see Figure 8). Do not discard the protective socket cover. Always replace the socket cover if the processor is removed from the socket. Figure 8.
Intel Desktop Board DQ965CO Product Guide 6. Hold the processor with your thumb and index fingers oriented as shown in Figure 10. Make sure fingers align to the socket cutouts (Figure 10, A). Align notches (Figure 10, B) with the socket (Figure 10, C). Lower the processor straight down without tilting or sliding the processor in the socket.
Installing and Replacing Desktop Board Components Installing the Thermal Module Desktop board DQ965CO has four mounting holes for a BTX Thermal Module. The board will accept either a Type I or Type II Thermal Module. Use the correct Thermal Module for your chassis.
Intel Desktop Board DQ965CO Product Guide 3. Make sure not to pinch the Thermal Module Fan cable between the Thermal Module and the desktop board or SRM (see Figure 13). Figure 13. Use Care Routing the Thermal Module Fan Cable 4.
775-Land Package (BTX) Removing the Processor For instructions on how to remove the Thermal Module and processor, refer to the processor installation manual or the Intel World Wide Web site at: ® ® Integration Overview for Systems Based on the Boxed Intel...
® The Intel Management Engine in the chipset requires memory to be populated in Channel A, DIMM 0 in order for it to enable Intel Quiet System Technology and Intel Active Management Technology. Two or Four DIMMs Install a matched pair of DIMMs equal in speed and size (see Figure 16) in DIMM 0 (blue) of both channels A and B.
Installing and Replacing Desktop Board Components If additional memory is to be used, install another matched pair of DIMMs in DIMM 1 (black) in both channels A and B (see Figure 17). Figure 17. Dual Channel Memory Configuration Example 2 Three DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) and DIMM 1 (black) of channel A.
DIMM in Figure 19. All the notches should match with the DDR2 DIMM. Figure 19. Use DDR2 DIMMs NOTE Memory must be installed in the Channel A, DIMM 0 socket to enable Intel Quiet System Technology and Intel Active Management Technology.
Installing and Replacing Desktop Board Components To install a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" on page 27. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3.
Intel Desktop Board DQ965CO Product Guide Removing DIMMs To remove a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" on page 27. 2. Turn off all peripheral devices connected to the computer. Turn off the computer.
Installing and Replacing Desktop Board Components Installing and Removing a PCI Express x16 Card CAUTION When installing a PCI Express x16 card on the desktop board, ensure that the card is fully seated in the PCI Express x16 connector before you power on the system. If the card is not fully seated in the PCI Express connector, an electrical short may result across the PCI Express connector pins.
Intel Desktop Board DQ965CO Product Guide Removing the PCI Express x16 Card Follow these instructions to remove the PCI Express x16 card from the connector: 1. Observe the precautions in "Before You Begin" on page 27. 2. Remove the screw (Figure 22, A) that secures the card’s metal bracket to the chassis back panel.
• Observe the precautions in "Before You Begin" on page 27. • Attach the cable end with the single connector (blue) to the Intel desktop board (Figure 23, A). • Attach the cable end with the two closely spaced connectors (gray and black) to the drives (Figure 23, B).
Intel Desktop Board DQ965CO Product Guide Connecting the Serial ATA (SATA) Cable The SATA cable supports the Serial ATA protocol and connects a single drive to the desktop board. For correct cable function: 1. Observe the precaution in "Before You Begin" on page 27.
Installing and Replacing Desktop Board Components Connecting to Internal Headers Before connecting cables to the internal headers, observe the precautions in "Before You Begin" on page 27. Figure 25 shows the location of the internal headers. Item Description Front panel audio USB 2.0 IEEE 1394a Serial port...
Figure 25, A on page 47 shows the location of the yellow front panel audio header. Table 5 shows the pin assignments for the front panel audio header. Table 5. Front Panel Audio Header Signal Names for Intel High Definition Audio...
Installing and Replacing Desktop Board Components To restore back panel audio, follow these steps: 1. Observe the precautions in "Before You Begin" on page 27. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3.
Intel Desktop Board DQ965CO Product Guide Connecting to the Alternate Front Panel Power LED Header Figure 25, E on page 47 shows the location of the alternate front panel power LED header. Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header.
Installing and Replacing Desktop Board Components Connecting to the Parallel Port Header See Figure 25, G for the location of the parallel port header. Table 10 shows the pin assignments for the header. Table 11. Parallel Port Header Signal Names Signal Name Signal Name STROBE#...
Intel Desktop Board DQ965CO Product Guide Connecting to the HD Audio Link Header See Figure 25, H for the location of the HD Audio Link header. Table 10 shows the pin assignments for the header. Table 13. HD Audio Link Header Signal Names...
Installing and Replacing Desktop Board Components Connecting Chassis Fan and Power Cables Connecting Chassis Fan Cables Connect the chassis fan cables to the two chassis fan headers on the desktop board. Figure 27 shows the location of the chassis fan headers. Figure 27.
Intel Desktop Board DQ965CO Product Guide Connecting Power Cables CAUTION Failure to use the appropriate power supply and/or not connecting the 12 V (2 x 2 pin) power connector to the desktop board may result in damage to the board or the system may not function properly.
Installing and Replacing Desktop Board Components Other Connectors and Headers Figure 29 shows the location of the other connectors and headers on the desktop board. Item Description PCI Express x1 connector PCI bus connector 1 PCI bus connector 2 Diskette drive connector Chassis intrusion header Figure 29.
Intel Desktop Board DQ965CO Product Guide Setting the BIOS Configuration Jumper NOTE Always turn off the power and unplug the power cord from the computer before moving the jumper. Moving the jumper with the power on may result in unreliable computer operation.
Installing and Replacing Desktop Board Components The three-pin BIOS jumper block enables all board configurations to be done in the BIOS Setup program. Table 14 shows the jumper settings for the BIOS Setup program modes. Table 14. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode...
Intel Desktop Board DQ965CO Product Guide Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode. 1. Observe the precautions in "Before You Begin" on page 27.
Installing and Replacing Desktop Board Components Back Panel Connectors NOTE The line out connector, located on the back panel, is designed to power either headphones or amplified speakers only. Poor audio quality may occur if passive (non-amplified) speakers are connected to this output. Figure 31 shows the back panel connectors.
Intel Desktop Board DQ965CO Product Guide Replacing the Battery A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery.
Page 61
Installing and Replacing Desktop Board Components VORSICHT Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend. AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto.
Page 62
Intel Desktop Board DQ965CO Product Guide VIGYAZAT Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni. AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh.
Page 63
Installing and Replacing Desktop Board Components UYARI Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır. OСТОРОГА Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху. Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей...
Intel Desktop Board DQ965CO Product Guide To replace the battery, follow these steps: 1. Observe the precautions in "Before You Begin" (see page 27). 2. Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter).
Power-On Self-Test (POST) memory test begins and before the operating system boot begins. This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an update fails.
Updating the BIOS with the ISO Image BIOS Update File The ISO Image BIOS update allows for the update of an Intel Desktop Board BIOS to the latest production release regardless of the operating system installed on the computer's hard drive and without the need to remove the BIOS configuration jumper.
CD-ROM, bootable USB flash drive, or other bootable USB media. The utility available on the Intel World Wide Web site provides a simple method for creating a bootable CD-ROM that will automatically update your BIOS. The Iflash BIOS update files can also be extracted locally to your hard drive and copied to a bootable USB flash drive or other bootable USB media.
BIOS could be damaged. Due to BIOS size and recovery requirements, a CD-R with the .BIO file in the root directory will be required. For more information about recovering the BIOS for desktop board DQ965CO, go to: http://support.intel.com/support/motherboards/desktop/...
Once RAID is enabled, the SATA port mapping for this desktop board changes. Figure 33 shows the original SATA port configuration for the board as indicated on the board silkscreen. Figure 34 shows the SATA port configuration after RAID is enabled. Figure 33. Original SATA Port Mapping for Desktop Board DQ965CO...
® Creating Your RAID Set 1. Upon re-boot, you will see the following Intel Matrix Storage Manager option ROM status message on the screen: Press <Ctrl-I> to enter the RAID Configuration Utility. Press <Ctrl-I> and enter the RAID Configuration Utility.
Controller (Desktop ICH8R)” driver. 3. Finish the Windows installation and install all necessary drivers. 4. Install the Intel Matrix Storage Console software via the Intel Express Installer CD included with your desktop board or after downloading it from the Internet at http://support.intel.com/support/motherboards/desktop/.
A Error Messages and Indicators Desktop Board DQ965CO reports POST errors in two ways: • By sounding a beep code • By displaying an error message on the monitor BIOS Beep Codes The BIOS also issues a beep code (one long tone followed by two short tones) during POST if the video configuration fails (a faulty video card or no card installed) or if an external ROM module does not properly checksum to zero.
Product Ecology statements • Electromagnetic Compatibility (EMC) regulations • Product certifications Safety Regulations Desktop Board DQ965CO complies with the safety regulations stated in Table 17 when correctly installed in a compatible host system. Table 17. Safety Regulations Regulation Title UL 60950-1:2003/ Information Technology Equipment –...
Intel Desktop Board DQ965CO Product Guide European Union Declaration of Conformity Statement We, Intel Corporation, declare under our sole responsibility that the product Intel ® Desktop Board DQ965CO is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directive 89/336/EEC (EMC Directive) and Council Directive 73/23/EEC (Safety/Low Voltage Directive).
The following information is provided to address worldwide product ecology concerns and regulations. Recycling Considerations As part of its commitment to environmental responsibility, Intel has implemented the Intel Product Recycling Program to allow retail consumers of Intel’s branded products ®...
Page 78
Français Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en œuvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits usés en les retournant à...
Page 79
& syarat, dsb. Portuguese Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados, onde esses produtos são reciclados de maneira adequada.
Intel Desktop Board DQ965CO Product Guide Türkçe Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya koymuştur. Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve şartlar v.s dahil bütün ayrıntılarını...
Regulatory Compliance EMC Regulations Desktop Board DQ965CO complies with the EMC regulations stated in Table 19 when correctly installed in a compatible host system. Table 19. EMC Regulations Regulation Title FCC Class B Title 47 of the Code of Federal Regulations, Parts 2 and 15, Subpart B, Radio Frequency Devices.
Intel Desktop Board DQ965CO Product Guide Korean Class B statement translation: This is household equipment that is certified to comply with EMC requirements. You may use this equipment in residential environments and other non-residential environments. Ensure Electromagnetic Compatibility (EMC) Compliance...
Regulatory Compliance Product Certifications Board-Level Certification Markings Desktop Board DQ965CO has the following product certification markings: Table 20. Product Certification Markings Description Mark UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel desktop boards: E210882. FCC Declaration of Conformity logo mark for Class B equipment.
Intel Desktop Board DQ965CO Product Guide Chassis and Component Certifications Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used. Agency certification marks on the product are proof of certification. Typical...