Asus P5N32-SLI SE DELUXE User Manual page 57

P5n32-sli se deluxe english edition user's manual
Hide thumbs Also See for P5N32-SLI SE DELUXE:
Table of Contents

Advertisement

2 .
2 .
2 . 2 .
I D E c o n n e c t o r ( s ) ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
I D E c o n n e c t o r ( s ) ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
I D E c o n n e c t o r ( s ) ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
2 .
I D E c o n n e c t o r ( s ) ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
I D E c o n n e c t o r ( s ) ( 4 0 - 1 p i n P R I _ I D E , S E C _ I D E )
The onboard IDE connectors are for Ultra DMA (133/)100/66 signal
cables. There are three connectors on each Ultra DMA 133/100/66
signal cable: blue, black, and gray. Connect the blue connector to
the motherboard's IDE connector, then select one of the following
modes to configure your devices.
Single device
Two devices
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
If any device jumper is set as "Cable-Select," make sure all other device
jumpers have the same setting.
®
P5N32-SLI SE Deluxe IDE connectors
A S U S P 5 N 3 2 - S L I S E D e l u x e
A S U S P 5 N 3 2 - S L I S E D e l u x e
A S U S P 5 N 3 2 - S L I S E D e l u x e
A S U S P 5 N 3 2 - S L I S E D e l u x e
A S U S P 5 N 3 2 - S L I S E D e l u x e
D r i v e j u m p e r
D r i v e j u m p e r
D r i v e j u m p e r
D r i v e j u m p e r
D r i v e j u m p e r
s e t t i n g
s e t t i n g
s e t t i n g
s e t t i n g
s e t t i n g
Cable-Select or Master
Cable-Select
Master
Slave
PIN 1
M o d e
M o d e
M o d e
M o d e
M o d e
C a b l e
C a b l e
C a b l e
C a b l e
C a b l e
o f d e v i c e ( s )
o f d e v i c e ( s )
c o n n e c t o r
c o n n e c t o r
o f d e v i c e ( s )
o f d e v i c e ( s )
o f d e v i c e ( s )
c o n n e c t o r
c o n n e c t o r
c o n n e c t o r
-
Black
Master
Black
Slave
Gray
Master
Black or gray
Slave
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
2 - 3 1
2 - 3 1
2 - 3 1
2 - 3 1
2 - 3 1

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents