Brother BE-0901E-AC Programming Instructions Manual
Programming the machine settings - english
Hide thumbs
Also See for BE-0901E-AC:
- Instruction manual (16 pages) ,
- Brochure & specs (4 pages) ,
- Upgrade manual (3 pages)
Advertisement
Quick Links
B
E
-
1
B
E
-
1
For Technical Assistance Please Call Toll Free
Website:
http://www.brother-usa.com/industembroidery/tech_down.aspx
If your machine settings have not been programmed or if a "hard
reset" has been completed (necessitating reprogramming), these
instructions will walk you through programming the settings list.
PLEASE READ THESE INSTRUCTIONS
COMPLETELY BEFORE ATTEMPTING
ANY OF THESE PROGRAMMING STEPS.
To reset the machine to the default settings:
1. "Power off" the machine.
2. Press and hold the
3. "Power on" the machine. Release the
key after the machine completes the "boot-up"
process.
Press the
4.
display
.
Let the machine complete the deletion process
before continuing.
2
0
1
B
,
2
0
1
B
,
Email:
tsupport@brother.com
key, when it is available on the
1
9
0
1
E
-
9
0
1
E
-
1-877-4BROTHER
key on the panel.
A
C
A
C
Advertisement
Related Manuals for Brother BE-0901E-AC
Summary of Contents for Brother BE-0901E-AC
- Page 1 For Technical Assistance Please Call Toll Free 1-877-4BROTHER Email: tsupport@brother.com Website: http://www.brother-usa.com/industembroidery/tech_down.aspx If your machine settings have not been programmed or if a “hard reset” has been completed (necessitating reprogramming), these instructions will walk you through programming the settings list. PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING ANY OF THESE PROGRAMMING STEPS.
- Page 2 Settings Programming starts: Press the key twice. Allow time for the display to react to the first keystroke. The screen should appear as such: Press the key, which will highlight the icon to the right. The Display should appear as such: Press the key.
- Page 3 Press the key. The screen should appear similar to such: The Thread Break feature has now been programmed. Press the key. The display should appear similar to: Press the key so the icon is highlighted. The display should appear as such (Next Page):...
- Page 4 Press the key. The display should appear as such: There are six speed ranges that can be programmed. The programming will be set from a high speed of 1000 SPM (Stitches per Minute) to 500 SPM, decreasing in 100 SPM increments. The image displayed above, shows the speed of ranges 1, 2, &...
- Page 5 key will not have to be pressed after setting the sixth speed range. The six speed ranges should now be programmed as 1000, 900, 800, 700, 600 & 500 SPM. Press the key 5 times, pausing to review each programmed value as you scroll. Verify each setting increases by a value of 100 SPM as you press the key.
- Page 6 Press the key. The display should appear as such: Press the key twice so the icon is highlighted. Let the display react to the first keystroke before pressing the key the second time. The display should appear as such: Press the key to change the trace from rectangular to octagonal.
- Page 7 Press the key. The display should appear as such: Press the key once. The display should appear as such: Press the key. The display should appear as such (Next Page):...
- Page 8 Press the key two times so the word “Beep” is highlighted. The screen should appear as such: There are three options for the “Beep” setting; OFF, ON, or 5. This will determine if the panel “beeps” when there is a thread break, or how many times it will beep.
- Page 9 Press the key until “0.2” replaces the word “OFF”. Each time one of the keys is pressed, the value will increase or decrease by 0.1 mm. The display should appear as such: Press the key. The display should appear as such: Press the key so the icon is highlighted.
- Page 10 Press the key. The display should appear as such: Each icon will have a slash through it as shown in the first icon. Press the key. The slash will be removed from the first icon. Press the key & then the key to remove the slash from the second icon.
- Page 11 Press the key. The display should appear as such: Press the key so the key is highlighted. The display should appear as such: Press the key. The display should appear as such: Press the key. The display should appear as such (Next Page):...
- Page 12 Press the key until the 0.0 value changes to 0.9 (1.1 for caps- explained on page 13), and press the key until the 1200 value changes to 700 (600 for caps). You are able to press any of the keys to increase or decrease both values. The display should appear as such: Press the key.
- Page 13 The screen should appear as such: The Short Pit speed limit feature will have to be programmed again when the CAP mode is selected. Power off the machine, and change the black frame mode switch from FLAT to CAP. Power “ON” the machine and press the twice, (allow time for the screen to accept each key selection).
- Page 14 Please note that some icons may appear differently on your machine panel, due to possible updates or changes in current machine firmware, (version 5.12 as of January 2009). For help or questions about these settings, please contact Brother Technical Service at 877-427-6843, or email Brother Technical Support at: tsupport@brother.com...