Related Manuals for Haier HWM1480KFL
Summary of Contents for Haier HWM1480KFL
- Page 1 HWM1480KFL Identification of parts Precautions HWM1480KFL Please read this manual carefully before use Keep this manual in a safe place...
-
Page 2: Identification Of Parts
Identification of parts Detergent dispenser HWM1480KFL drawer LCD display Start/Pause button Filter cover Water inlet valve connector Transporting bolts 1.The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be reused. - Page 3 Precautions 8.Machine door will lock suddenly when there is 7. Do not allow children to play with the loss of electricity or power failure. In order to packaging materials after unpacking. open the door in this event, open the filter cover at the bottom.
- Page 4 Precautions Ensure all surface and parts are dry before using the washing machine...
- Page 5 .This is drawer 7. The door is fitted with a self-lock device and will not open for approximately 1-2 minutes after the washing machine has stopped. Do not force open the door. Do not open the door when water level reaches above the port hole.
-
Page 6: Installation
Installation As shown in figure 1 (Fig. 1), remove all the packaging material before installing. Drops of water could be found on the packaging and/or door. This is a result from QC test run in the factory before shipment. Removing transporting The transporting bolt are designed for clamping anti-vibration components inside of the washing machine during the... - Page 7 Installation Connect and tighten the water intel hose to the water inlet valve connector.On the washing machine check that the connection is correct and secure. Conncet the cther end of the water inlet hose and tighten to the tap facet.Check that it is correct and secure.
-
Page 8: Control Panel Operating Functions
Control Panel Control Panel Operating Functions Turn the program knob clockwise/anti-clockwise to select your desired wash program. (Refer to "Guide to Operation Program Selection") This button is used to start or pause a wash cycle. you can press "start/pause button 2 second to unlocked and open the door if status allow door open (water level lower than the bottom of the door level,water temperature lower than 50 ,motor stop). - Page 9 This option should be selected for laundry which are heavily soiled. LCD display This LCD display screen will display the remaining wash time, temperature selection, speed selection, option selection and any alarm warning. (For details, please see "Description of option" on page 14) Child lock (Combined hold of Delay and Start/Pause option buttons) After having started the program, enable the child lock by pressing and holding the "Delay"...
-
Page 10: Program Selection
Program Selection cold-90 cold-90 cold-60 Wool cold-40 Wool Underwear Underwear cold-90 mixed Different material cold-40 Jeans cold-90 This wash is suitable for laundry which has been Sport cold-40 used after gym,exercise, light sports. Hand wash cold-40 cold Rinse Spin... - Page 11 Prep a rations...
- Page 12 W a s h i ng M e th o d s 1.Laundry loading Evenly load the laundry in the washing machine and then close the door ensuring that it is secure. 1) When using the washing machine for the first time, run an unloaded machine on one program.
- Page 13 Was h i ng M e th o d s Custom select wash temperature and spin speed. Select the most appropriate wash temperature and spin speed for your laundry load.Please refer to the "Program Guide" for recommendations. Selecting options Select any options which you may require with your laundry load. Switch off the power...
-
Page 14: Maintenance
M a intenance... -
Page 15: Troubleshooting
Trouble Shooting exceed If laundry washing too little make the machine unbalance The laundry washing enwind,tied or distribut not symmetrical Machine can not spin The laundry washing is sweater or clothes sucked much water Machine load is over 8kg . this because machine change operate time according the laundry balance and water temperature,it's nature set Program operate time change... - Page 16 D e s c r ip t ion of op t ions Foam test function display If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard ( For appliances with type Y attachment) 5.foam test function;this function just available to program both with main wash and rinse(include single rinse program),when the program test foam more then parameter will automaticly operate clean foam rinse program and adjust washing time.the display will show CLrF per ten second during the clean foam rinse program.
-
Page 17: Technical Specifications
Technical Specifications HWM1480KFL 850 650 595 2100 Display Display board 1 board 2 Heating element Filter MAIN BOARD Door lock Motor Valve Valve Pump Temperature sensor...