Yamaha DTX750K Assembly Manual

DTX750K
This pamphlet describes the standard procedure for DTX750K assembly.
After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.
Standard Assembly Example
PCY135 PCY155
(Cymbal Pad) (Cymbal Pad)
CH750
(Cymbal Holder)
XP80
(Tom Pad)
RHH135
(Real Hi-hat Pad)
DTX700 Drum
Trigger Module
XP100SD
(Snare Pad)
HS650
(Hi-hat Stand)
KP65
(Kick Pad)
SS662
(Snare Stand)
Before using, please read this assembly manual, and use this product in a safe and proper manner.
* Please keep this manual in a safe place for future reference.
* Make sure to read the Assembly Manual of the Rack System and the Owner's Manual of the Pad.
If this symbol is ignored and the equipment is used improperly,
WARNING
fatal injury to persons or serious damage could occur.
• Do not let small children assemble or set up this product by themselves, or they may be injured.
Always assemble this product with adult supervision.
• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends
may result in injury.
• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends
may result in injury.
• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened
firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may
result in the rack overturning or parts dropping, causing injury.
• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on
steps may result in the product being unstable and subject to overturning.
• When setting up the product, please pay close attention to the handling and setting of cables.
Carelessly placed cables may cause the user and others to trip and fall.
• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.
• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.
* Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
Assembly Manual EN
IMPORTANT
• For assembly, you will require four individual packages – an RS700
Rack System, a DTP750C Pad Set, a DTP750P Pad Set, and a
DTX700 Drum Trigger Module.
• This pamphlet describes how to attach the pads and drum trigger
CH750
module to the RS700 Rack System. Before carrying out the proce-
(Cymbal Holder)
dures described below, ensure that you have correctly assembled
the rack system as described in its assembly manual.
PCY135
(Cymbal Pad)
NOTICE
CH755
(Cymbal Holder) Before starting assembly, lay a drum mat (sold separately) on the floor.
Alternatively, before setting up the HS650A Hi-hat Stand and KP65
Kick Pad, you can place the packages' cardboard boxes on the floor to
protect it from damage
XP80
(Tom Pad)
RS700
(Rack System)
PRECAUTIONS
If this symbol is ignored and the equipment is used improperly,
CAUTION there is a danger or injury to persons handling the equipment, and
material damage could occur.
• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.
• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your
fingers.
• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting
in injury.
• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums
may drop, causing injury.
NOTICE
• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,
never place any heavy or sharp objects on the cable. Applying excessive force to the cable may
result in damage to the cable, such as the wires being severed, etc.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,
close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).
Doing so may result in deformation, discoloration, damage or deterioration.
• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or
deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has
been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to
let the water and detergent come into contact with the cushions used in the product; doing so may
result in deterioration.
Assemble the RS700 Rack System.
1
Digital Musical Instruments Division Digital Musical Instruments Division For details, refer to the assembly manual that came with the rack system.
©2011 Yamaha Corporation
WW60710 103PO***.*01B0
Check the contents of each package.
2
Package 1: DTP750C
 PCY135  PCY155
Cymbal Pad (x2) Cymbal Pad (x1)
 CH750  CH755
Cymbal Holder (x2) Cymbal Holder (x1)
 10-channel snake cable (x1)
 PCY100, PCY135, and PCY155 Owner's Manual (x1)
 RHH135 Owner's Manual (x1)
 Assembly Manual (this pamphlet)
Mount the pads and the drum trigger module on the rack system.
3
As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat.
Mounting the cymbal holders
1.
Mount the cymbal holders (CH750 x 2, CH755 x 1) on
the rack system as shown below.
CH750
Package 2: DTP750P
 RHH135  Stand base for the  XP100SD
Real Hi-hat Pad (x1) RHH135 (x1)
 Hi-hat clutch for the
RHH135 (x1)
 HS650A
 Clamp bolts (x4)
Hi-hat Stand (x1)
 Clamp bolt small (x1)
 Cable band for the
RHH135 (x1)
 XP100T, XP100SD, XP120T, and XP120SD Owner's Manual (x1)
 XP70 and XP80 Owner's Manual (x1)
 KP65 Owner's Manual (x1)
 Stoppers for the
PCY135 and
PCY155 (x3)
Package 3: DTX700
 DTX700 Drum Trigger
 Felts for the
PCY135 and
PCY155 (x3)
 Tuning key (x1)
 Cable band (x10)  DTX700 Owner's Manual (x1)
 DTX700 Data List (x1)
 DVD (containing software)
Mounting the tom pad
XP80
CH750
CH755
1.
Attach the clamp bolt to each of the tom pads
and provisionally tighten (by 5 or 6 turns).
Clamp bolt (to be tight-
ened in the direction
shown)
Tom pad (rear side)
 XP80  SS662
Snare Pad (x1) Tom Pad (x3) Snare Stand (x1)
 KP65
Kick Pad (x1)
 Module stand (x1)  AC power adaptor*
Module (x1) (x1)
 Module stand
fastening screws (x4)
* May not be included de-
pending on your particular
area. Please check with
your Yamaha dealer.
2.
Mount the tom pads on the rack's clamp rods.
As shown below, ensure that the rod section
is fully inserted into each pad's mounting hole,
and then fully tighten the clamp bolt.
Tom pad Clamp rod
Rod
section
Insert
Clamp bolt
3.
If necessary, use clamp bolts A to E to adjust
the height and angle of any of the pads. When
doing so, be sure to adjust one bolt at a time
(i.e., loosen a bolt, adjust the pad, and then
retighten before loosening another).
Clamp bolt B
Clamp bolt D
Clamp bolt E
Clamp bolt A
Clamp bolt C
Continued on other side