Yamaha CP5 Data List page 26

[3] DYNAMIC FILTER
No. Parameter
1 Filter Type LPF (12dB), LPF (18dB), LPF
(24dB), HPF, BPF, BEF
2 Sensitivity 0 – 127
3 Dyna Level Offset 0 – 127
4 Resonance -16 – +111
5 Attack Time 0.3ms – 227ms
6 Release Time 2.6ms – 2171ms
7 Release Curve 0 – 127
8 Direction up, down
9 Dyna Threshold Level 0 – 127
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 22.
[4] AUTO SYNTH
No. Parameter
1 Mod Speed 0 – 127
2 Mod Wave Type Type A, Type B, Type C,
Type D
3 Mod Depth 0 – 127
4 Mod Depth Ofst R -63 – +63
5 HPF Cutoff Frequency 20Hz – 8.0kHz
6 LPF Cutoff Frequency 1.0kHz – 20.0kHz
7 Delay Time 0.1 – 370.0ms
8 Delay Time Ofst R 0 – 884
9 Delay Level 0 – 127
10 Dry Mix Level 0 – 127
11 Feedback Level -63 – +63
12 FB Level Ofst R -63 – +63
13 AM Speed 0.00Hz – 39.7Hz
14 AM Wave tri, sine, saw up, saw down
15 AM Depth 0 – 127
16 AM Inverse R normal, inverse
[5] ISOLATOR
No. Parameter
1 On/off Switch on, off
2 Low Level -64 – +63
3 Mid Level -64 – +63
4 High Level -64 – +63
5 Low Mute off/on
6 Mid Mute off/on
7 High Mute off/on
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
*3: On/off Switch cannot be controlled using the pitch bend wheel.
[6] TECH MODULATION
No. Parameter
1 Mod Speed 0 – 127
2 Mod Depth 0 – 127
3 Mod Gain -12 – +12dB
4 Mod Mix Balance D63>W – D=W – D<W63
5 Pre Mod HPF Cutoff 20Hz – 8.0kHz
Frequency
6 Mod LPF Cutoff Frequency 1.0kHz – 20.0kHz
7 Mod LPF Resonance 1.0 – 12.0
8 Delay Time 0.1 – 740.0ms
9 Delay Time Ofst R 0 – 884
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Feedback Level -63 – +63
12 FB Level Ofst R -63 – +63
13 Feedback Hi Damp 0.1 – 1.0
14 FB Hi Damp Ofst R -0.9 – +0.9
15 —
16 —
Range Value Control
(0 – 5)

(0 – 127)
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 1)
(0 – 127)
(1 – 127)
Range Value Control

(0 – 127)
(0 – 3)
(0 – 127)
(1 – 127)
(0 – 52)
(34 – 60)
(1 – 3700)
(0 – 884)
(0 – 127)
(0 – 127)
(1 – 127)
(1 – 127)
(0 – 127)
(0 – 3)
(0 – 127)
(0 – 1)
Range Value Control
*3
(0 – 1)
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 1)
(0 – 1)
(0 – 1)
Range Value Control

(0 – 127)
(0 – 127)
(52 – 76)
(1 – 127)
(0 – 52)
(34 – 60)
(10 – 120)
(1 – 7400)
(0 – 884)
(1 – 127)
(1 – 127)
(1 – 127)
(1 – 10)
(1 – 19)
Effect Parameter List for Other Group
Category — MISC
[1] VCM EQ 501
No. Parameter
1 EQ1 (LSH) Frequency 31.5Hz – 2.0kHz
2 EQ1 (LSH) Gain -12.0dB – +12.0dB
3 EQ2 Q 0.50 – 16.00
4 EQ2 Frequency 50.0 Hz – 20.0kHz
5 EQ2 Gain -18.0dB – +18.0dB
6 EQ3 Q 0.50 – 16.00
7 EQ3 Frequency 50.0 Hz – 20.0kHz
8 EQ3 Gain -18.0dB – +18.0dB
9 EQ4 Q 0.50 – 16.00
10 EQ4 Frequency 50.0 Hz – 20.0kHz
11 EQ4 Gain -18.0dB – +18.0dB
12 EQ5 (HSH) Frequency 500Hz – 20.0kHz
13 EQ5 (HSH) Gain -12.0dB – +12.0dB
14 Output Level -12.0dB – +12.0dB
15
16
[2] HARMONIC ENHANCER
No. Parameter
1 HPF Cutoff Frequency 500Hz – 16.0kHz
2 Drive 0 – 127
3 Mix Level 0 – 127
4 —
5 —
6 —
7 —
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
[3] Talking Modulator
No. Parameter
1 Vowel a/i/u/e/o
2 Move Speed 1 – 62
3 Drive 0 – 127
4 Output Level 0 – 127
5 —
6 —
7 —
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
Range Value Control
(12 – 84)
(60 – 300)
(0 – 60)
(20 – 124)
(0 – 360)
(0 – 60)
(20 – 124)
(0 – 360)
(0 – 60)
(20 – 124)
(0 – 360)
(60 – 124)
(60 – 300)
(60 – 300)
Range Value Control
(28 – 58)
(0 – 127)
(0 – 127)
Range Value Control

(0 – 4)
(1 – 62)
(0 – 127)
(0 – 127)
CP5 / CP50 Data List
26