Yamaha CP5 Data List page 25

Category — COMPRESSOR
[1] CLASSIC COMPRESSOR
No. Parameter
1 Attack 1ms – 40ms
2 Release 10ms – 680ms
3 Threshold -48dB – -6dB
4 Ratio 1 – 20.0
5 Output Level 0 – 127
6 —
7 —
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
[2] MULTI BAND COMP
No. Parameter
1 Low Attack 1ms – 200ms
2 Low Threshold -54dB – -6dB
3 Low Ratio 1 – 20.0
4 Low Gain -∞ – +18dB
5 Mid Attack 1ms – 200ms
6 Mid Threshold -54dB – -6dB
7 Mid Ratio 1 – 20.0
8 Mid Gain -∞ – +18dB
9 High Attack 1ms – 200ms
10 High Threshold -54dB – -6dB
11 High Ratio 1 – 20.0
12 High Gain -∞ – +18dB
13 Divide Freq Low 16Hz – 20kHz
14 Divide Freq High 16Hz – 20kHz
15 Common Release 10msec – 3000msec
16 —
When the value of Bottom is greater than Top, the sound will not be modulated and only the Bottom
value is available.
Category — Lo-Fi
[1] LO-FI
No. Parameter
1 Sampling Freq. Control 44.1 – 344Hz
2 Word Length 1 – 127
3 Output Gain -6dB – +36dB
4 Pre-LPF Cutoff Frequency 63Hz – 20.0kHz
5 Filter Type thru, Power Bass, Radio,
Telephone, Clean, Low
6 Pre-LPF Resonance 1 – 12.0
7 Bit Assign 0 – 6
8 Emphasis off/on
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 —
14 —
15 Input Mode mono, stereo
16 —
Range Value Control
(0 – 19)
(0 – 15)
(79 – 121)
(0 – 7)
(0 – 127)
Range Value Control
(0 – 29)
(73 – 121)
(0 – 7)
(0 – 55)
(0 – 29)
(73 – 121)
(0 – 7)
(0 – 55)
(0 – 29)
(73 – 121)
(0 – 7)
(0 – 55)
(0 – 124)
(0 – 124)
(0 – 23)
Range Value Control
(0 – 127)
(1 – 127)
(0 – 42)
(10 – 60)
(0 – 5)
(10 – 120)
(0 – 6)
(0 – 1)

(1 – 127)
(0 – 1)
Effect Parameter List for Other Group
[2] NOISY
No. Parameter
1 Mod Depth 0 – 10
2 Mod Speed 0 – 127
3 Mod Feedback -63 – +63
4 Mod Mix Balance 1 – 127
5 Drive 0 – 127
6 AM Speed 0.00Hz – 39.7Hz
7 AM Depth 0 – 127
8 LPF Cutoff Frequency 1.0kHz – 20.0kHz
9 LPF Resonance 1.0 – 12.0
10 Dry/Wet Balance D63>W – D=W – D<W63
11 EQ Frequency 100Hz – 10.0kHz
12 EQ Gain -12 – +12dB
13 EQ Width 1.0 – 12.0
14 —
15 —
16 —
[3] DIGITAL TURNTABLE
No. Parameter
1 Click Density 0 – 5
2 Click Level 0 – 127
3 Noise Tone 0 – 6
4 Noise Mod Speed 0.00Hz – 39.7Hz
5 Noise Mod Depth 0 – 127
6 Dry Send to Noise 0 – 127
7 Noise LPF Cutoff Frequency 1.0kHz – 20.0kHz
8 Noise LPF Q 1.0 – 12.0
9 Noise Level 0 – 127
10 —
11 Dry Level 0 – 127
12 Dry LPF Cutoff Frequency 1.0kHz – 20.0kHz
13 —
14 —
15 —
16 —
Category — TEC
[1] RING MODULATOR
No. Parameter
1 OSC Frequency Coarse 0.5 – 5kHz
2 OSC Frequency Fine 0 – 127
3 LFO Wave tri, sine
4 LFO Depth 0 – 127
5 LFO Speed 0.0Hz – 39.70Hz
6 HPF Cutoff Frequency 20Hz – 8.0kHz
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz
8 —
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 22.
[2] DYNAMIC RING MODULATOR
No. Parameter
1 Sensitivity 0 – 127
2 HPF Cutoff Frequency 20Hz – 8.0kHz
3 LPF Cutoff Frequency 1.0kHz – 20.0kHz
4 Attack Time 0.3ms – 227ms
5 Release Time 2.6ms – 2171ms
6 Release Curve 0 – 127
7 Direction up, down
8 Dyna Threshold Level 0 – 127
9 Dyna Level Offset 0 – 127
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 22.
Range Value Control

(0 – 10)
(0 – 127)
(1 – 127)
(1 – 127)
(0 – 127)
(0 – 127)
(0 – 127)
(34 – 60)
(10 – 120)
(1 – 127)
(14 – 54)
(52 – 76)
(10 – 120)
Range Value Control
(0 – 5)
(0 – 127)
(0 – 6)

(0 – 127)
(0 – 127)
(0 – 127)
(34 – 60)
(10 – 120)
(0 – 127)
(0 – 127)
(34 – 60)
Range Value Control

(0 – 127)
(0 – 127)
(0 – 1)
(0 – 127)
(0 – 127)
(0 – 52)
(34 – 60)
(1 – 127)
Range Value Control

(0 – 127)
(0 – 52)
(34 – 60)
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 1)
(0 – 127)
(0 – 127)
(1 – 127)
CP5 / CP50 Data List
25