Advertisement
DISASSEMBLY - LEF SIDE (Continuation):
7. Install 02 sensor on new manifold. Use anti-seize
compound on threads.
8. Replace spark plug wires.
9. Replace A.I.R. assembly using supplied gasket.
RIGHT SIDE
1. Disconnect and remove spark plug wires.
2. Disconnect A.I.R. assembly from manifold.
3. Remove bolts from EGR flange, if equipped.
4. Remove dip stick.
5. Remove bolts from manifold.
6. Remove stock manifold from below.
7. Install flange gasket and one 8mm bolt, lock washer,
and flat washer at rearmost bolthole (leave bolt loose
enough to accept header).
Note: If your vehicle does not have an EGR, install
supplied block off plate with gasket and two 5/16"
bolts and lock washers (kit items) to header before
installation.
8. Place header into position from below car and start
one bolt at front. Note: Use flat washers and lock
washers on all bolts.
Qty.
Part #
❑ 1
25-9265
❑ 1
25-9266
❑ 1
25-9245
❑ 1
25-9246
❑ 12
-
❑ 2
-
❑ 1
-
❑ 1
-
❑ 2
-
©2006 Edelbrock Corporation
Catalog #65732 & #65733
Description
Manifold left side (Ceramic-Coated)
Manifold right side (Ceramic-Coated)
Manifold left side (Ti-Tech Coated)
Manifold right side (Ti-Tech Coated)
Hex header bolts: 8mm x
1.25" x 30mm
LS-2 V8 port gaskets
Catalytic converter gasket (left)
Catalytic converter gasket (right)
5/16" x 1" Hex bolts
Edelbrock Corporation, 2700 California Street, Torrance, CA 90503
Toll-Free Tech Line: 1-800-416-8628
Tech E-Mail: Edelbrock@Edelbrock.com
9. Install all manifold bolts and tighten.
10. Re-attach EGR tube (if equipped) using supplied
gasket and 5/16" bolts and lock washers.
11. Re-attach spark plug wires.
12. Re-install dip stick tube.
13. Re-attach A.I.R. assembly.
FINAL ASSEMBLY
1. Using supplied 3/8-16 x 1 1/2" bolts, lock washers,
flat washers, nut and catalytic converter flange
gaskets, re-install catalytic converter assemblies.
2. Re-install all 02 sensors (use anti-seize compound).
FINAL INSPECTION
1. Check all hydraulic, vacuum, and fuel lines to ensure
there is adequate clearance to TES components.
2. Re-connect battery.
3. At this point, it is a good idea to look everything over
and make sure that nothing was missed in assembly.
4. Start vehicle and bring up to normal operating
temperature. Check for possible leaks.
5. Turn engine off and let cool. Tighten all bolts again.
PARTS LIST
#65732 & 65733
Qty.
❑ 6
❑ 6
❑ 6
❑ 14
❑ 12
❑ 1
❑ 2
❑ 6
❑ 1
®
Page 2 of 2
Part #
Description
-
3/8"-16 Hex nuts
-
3/8"-16 x 1-1/2" Hex bolts
-
Flat washers
-
5/16" Lock washers
-
5/16" I.D. x 1/8" thick Hardened
washers
-
EGR gasket
-
A.I.R. gasket
-
3/8" Lock washers
-
EGR Block-off plate
Brochure #63-0405
Rev. 7/06
Advertisement
