Remote Control; Placing The Television In Standby Mode - Samsung CS-29A11PQ Owner's Instructions Manual

Remote Control

(depending on the model)
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
Œ Œ POWER ˆ ˆ -/--
Used to switch the TV Used to select a channel
on and off. numbered ten or over.
Press this button, then
´ ´ DUAL I-II
"--" symbol is
Used to select the
displayed. Enter the
sound mode.
two-digit channel
ˇ ˇ P.SIZE
number.
Used to change the
Ø Ø MUTE
screen size.
Used to switch the
¨ ¨ Numeric buttons
sound off temporarily. To
Used to select channels turn the sound back on,
directly. press the MUTE,
button.
∏ ∏
/
Used to increase or
decrease the volume.
" " TV
Used to return to the TV
mode when it is in
external input mode.
' ' MENU
Used to display the on-
screen menu or return to
the previous menu.
˝ ˝ ... ... / † † / œ œ / √ √
Used to control the
cursor in the menu.
Ô Ô TURBO
Used to select the turbo
sound option.
  S.MENU
Used to display the
sound menu.
Ò Ò SLEEP
Used to select a preset
time interval for
automatic shut off.
Ú Ú PRE-CH
Used to switch
repeatedly between the
last two channels
displayed.
Installing Batteries
Remove the cover. Install two AAA
size batteries, then replace the cover.
When the remote control does not
operate normally, check that the "+" and "-" ends of the
, or
batteries are inserted correctly or the batteries are drained.
➢
Do not mix battery types, i.e. alkaline and manganese.
English - 2
Æ Æ VIDEO
Switching the Television On and Off
Used to display all of the
available video sources.
The mains lead is attached to the rear of the television.
ı ı P
/
1
Used to display the next
or previous stored
channel.
˜ ˜ INFO
2
Used to view the
channel information and
3
setting status you
selected. (Depending on
the model, the signal
strength symbol ( )
can be displayed.)
¯ ¯ EXIT
Used to exit from any
display or return to
normal viewing.
˘ ˘ ENTER
4
While using the on-
screen menus, press the
ENTER button to
activate (or change) a
particular item.
¿ ¿ P.MODE
Used to select the

Placing the Television in Standby Mode

picture effect.
¸ ¸ S.MODE
The television can be placed in standby mode, in order to
Used to select the
reduce power consumption and wear of the cathode ray
sound effect.
tube. Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1
2
☛
Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
Press the button (On/Off) on the front (or side) of the
television.
Press the POWER button on the remote control to
switch the television on. The programme that you were
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to "Channel - Auto Store" or "Channel - Manual
Store" on page 4.
➢
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
"Setup - Plug & Play" on page 3.
To switch the television off, press the button (On/Off)
on the front (or side) of the television.
Press the POWER button on the remote control while
viewing.
The television is in standby mode.
To switch the television back on, simply press it again.
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.