Hitachi CP-WX3014WN Technical Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Projector
  5. CP-WX3014WN
  6. Technical manual
Hitachi CP-WX3014WN Technical Manual

Hitachi CP-WX3014WN Technical Manual

User manual
Hide thumbs Also See for CP-WX3014WN:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual, User Manual
Projector
CP-X2514WN/CP-X3014WN/
CP-X4014WN/CP-WX3014WN
User's Manual (detailed)
Operating Guide – Technical
Example of computer signal
Resolution (H x V) H. frequency (kHz)
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 768
1280 x 800
1280 x 960
1280 x 1024
1280 x 1024
*1 1280 x 1024
*2 1400 x 1050
1440 x 900
*3 1680 x 1050
*1 1600 x 1200
*1) Supported except for HDMI input.
*2) Only for CP-X2514WN, CP-X3014WN and CP-X4014WN.
NOTE
• Be sure to check jack type, signal level, timing and resolution before
connecting this projector to a computer.
• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possible in some cases.
Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA (1600x1200), the signal
will be converted to the projector's panel resolution before being displayed. The best display
performance will be achieved if the resolutions of the input signal and projector panel are identical.
• Automatic adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a composite
sync or a sync on G.
V. frequency (Hz)
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
48.4
56.5
60.0
68.7
67.5
47.7
49.7
60.0
64.0
80.0
91.1
65.2
55.9
65.3
75.0
Rating
85.0
VESA
59.9
VESA
72.8
VESA
75.0
VESA
85.0
VESA
56.3
VESA
60.3
VESA
72.2
VESA
75.0
VESA
85.1
VESA
74.5
60.0
VESA
70.1
VESA
75.0
VESA
85.0
VESA
75.0
VESA
60.0
VESA
60.0
VESA
60.0
VESA
60.0
VESA
75.0
VESA
85.0
VESA
60.0
VESA
59.9
VESA
60.0
VESA
60.0
VESA
*3) Only for CP-WX3014WN.
Signal mode
TEXT
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (85Hz)
SVGA (56Hz)
SVGA (60Hz)
SVGA (72Hz)
SVGA (75Hz)
SVGA (85Hz)
Mac 16" mode
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (85Hz)
1152 x 864 (75Hz)
W-XGA (60Hz)
1280 x 800 (60Hz)
1280 x 960 (60Hz)
SXGA (60Hz)
SXGA (75Hz)
SXGA (85Hz)
SXGA+ (60Hz)
WXGA+ (60Hz)
WSXGA+ (60Hz)
UXGA (60Hz)
1

Advertisement

Table of Contents
loading

Related Manuals for Hitachi CP-WX3014WN

Summary of Contents for Hitachi CP-WX3014WN

  • Page 1 VESA UXGA (60Hz) *1) Supported except for HDMI input. *2) Only for CP-X2514WN, CP-X3014WN and CP-X4014WN. *3) Only for CP-WX3014WN. NOTE • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer.
  • Page 2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b)
  • Page 3 Connection to the ports Connection to the ports NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. ►Only the signal that is input from the COMPUTER IN1 or IN2 can be output from the MONITOR OUT port.
  • Page 4 Connection to the ports (continued) COMPONENT Cb/Pb Cr/Pr RCA jack x3 • System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60 Port Signal Component video Y, 1.0±0.1Vp-p with composite sync, 75Ω terminator Cb/Pb Component video Cb/Pb, 0.7±0.1Vp-p, 75Ω terminator Cr/Pr Component video Cr/Pr, 0.7±0.1Vp-p, 75Ω terminator S-VIDEO Mini DIN 4pin jack •...
  • Page 5 Connection to the ports (continued) HDMI • Type :Digital audio/video connector • Audio signal : Linear PCM (Sampling rate; 32/44.1/48 kHz) Signal Signal Signal T.M.D.S. Data2 + T.M.D.S. Data0 Shield 15 SCL T.M.D.S. Data2 Shield T.M.D.S. Data0 - 16 SDA T.M.D.S.
  • Page 6 Connection to the ports (continued) USB TYPE A USB TYPE B USB A type jack USB B type jack Signal Signal - Data - Data + Data + Data Ground Ground CONTROL D-sub 9pin plug • About the details of RS-232C communication, please refer to the following page.
  • Page 7 Connection to the ports (continued) To input SCART RGB signal; SCART connector (jack) SCART cable (plug) RCA plugs To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex.. For more reference, please consult your dealer.
  • Page 8 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&17). Connection Turn off the projector and the computer.
  • Page 9 RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps,8N1 2. Command format ("h" shows hexadecimal) Byte Number Command Header Data Header Data Setting Action Type code size flag code Packet Action <SET>Change setting to desired value [(cL)(cH)] (aL) (aH) 01h 00h (bL) (bH) (cL) (cH) by [(eL)(eH)].
  • Page 10 RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the code. (2) NAK reply : 15h When the projector cannot understand the received command, the projector returns the error code.

  • Page 11: Command Control Via The Network

    Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&17).
  • Page 12 Command Control via the Network (continued) Communicaion Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items form a web browser when command control is used. Port Settings Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23.

  • Page 13: Command Control Settings

    Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4).

  • Page 14: Response Code / Error Code

    Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (××h : connection ID) (1) ACK reply : 06h + ××h (2) NAK reoly : 15h + ××h (3) Error reply : 1Ch + 0000h + ××h...
  • Page 15 Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS- 232C communication can be controlled from the computer as a network terminal. For details, see the 6.

  • Page 16: Communication Settings

    Network Bridge Communication (continued) Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. (&OPTION menu - SERVICE - COMMUNICATION in the Operating Guide) Item Condition BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (fixed) PARITY NONE/ODD/EVEN...

  • Page 17: Picture Mode

    RS-232C Communication / Network command table RS-232C Communication / Network command table Command Data Names Operation Type Header Action Type Setting code Turn off BE EF 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 06 00 BA D2 01 00...
  • Page 18 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 89 D2 02 00 03 20 00 00 BRIGHTNESS Increment BE EF 06 00 EF D2 04 00 03 20 00 00 Decrement BE EF...
  • Page 19 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code User Gamma Execute BE EF 06 00 68 C3 06 00 54 70 00 00 Point 5 Reset BE EF 06 00 C4 FE 02 00 95 30 00 00...
  • Page 20 5E D7 01 00 08 20 08 00 NORMAL BE EF 06 00 5E DD 01 00 08 20 10 00 BE EF 06 00 AD D0 02 00 08 20 00 00 (*) only for CP-WX3014WN (continued on next page)

  • Page 21: Auto Adjust Execute

    RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 91 70 02 00 09 22 00 00 OVER SCAN Increment BE EF 06 00 F7 70 04 00 09 22 00 00 Decrement...
  • Page 22 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUTO BE EF 06 00 A2 70 01 00 11 22 0A 00 NTSC BE EF 06 00 C2 74 01 00 11 22 04 00 BE EF 06 00...
  • Page 23 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code NORMAL BE EF 06 00 D6 D2 01 00 01 60 00 00 STANDBY SAVING BE EF 06 00 46 D3 01 00 01 60 01 00 MODE...
  • Page 24 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 75 CD 02 00 62 20 00 00 VOLUME - Increment BE EF 06 00 13 CD 04 00 62 20 00 00 S-VIDEO...
  • Page 25 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code AUDIO IN1 BE EF 06 00 E6 DC 01 00 36 20 01 00 AUDIO IN2 BE EF 06 00 16 DC 01 00 36 20 02 00 AUDIO...

  • Page 26: Mic Level

    RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 02 F1 01 00 A1 20 00 00 MIC LEVEL HIGH BE EF 06 00 92 F0 01 00 A1 20 01 00 BE EF...
  • Page 27 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code MENU POSITION V Execute BE EF 06 00 A8 C7 06 00 44 70 00 00 Reset MyScreen BE EF 06 00 FB CA 01 00 00 30 20 00...

  • Page 28: Auto Power Off

    RS-232C Communication / Network command table (continued) RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 EA D1 01 00 0F 20 00 00 AUTO BE EF 06 00 7A D0 01 00 0F 20...
  • Page 29 RS-232C Communication / Network command table (continued) RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code COMPUTER IN1 BE EF 06 00 C6 32 01 00 01 36 00 00 COMPUTER IN2 BE EF 06 00 06 30...
  • Page 30 RS-232C Communication / Network command table (continued) Command Data Names Operation Type Header Action Type Setting code BE EF 06 00 3A C3 01 00 00 35 00 00 IMAGE-1 BE EF 06 00 AA C2 01 00 00 35 01 00 IMAGE-2 BE EF...

  • Page 31: Pjlink Command

    PJLink command PJLink command Commands Control Description Parameter or Response 0 = Standby POWR Power Contorol 1 = Power On 0 = Standby POWR ? Power Status inquiry 1 = Power On 2 = Cool Down 11 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO...
  • Page 32 HITACHI inquiry CP-X2514WN CP-X3014WN INF2 ? Model Name inquiry CP-X4014WN CP-WX3014WN Responds with the factory information and so INFO ? Other Information inquiry CLSS ? Class Information inquiry 1 NOTE • The password used in PJLink is the same as the password set in the Web Brouwser Comtrol.

This manual is also suitable for:

Cp-x4014wnCp-x3014wnCp-x2514wn

Table of Contents