Configuring Network Protocol Via The Machine; System Requirements; Windows - Samsung SCX-6555N User Manual

If you are in a non-static IP address environment and need to set up a
DHCP network protocol, go to
bonjour/download/, select the Bonjour program that is appropriate for
your computer operating system and install the program. This program
will allow you to set network parameters automatically. Follow the
instructions in the installation window. This program does not support
Linux.

Configuring network protocol via the machine

You can set up TCP/IP network parameters, follow the steps listed below.
1. Make sure your machine is connected to the network with an RJ-45
Ethernet cable.
2. Make sure you have turned on the machine.
3. Press Machine Setup on the control panel.
4. Press Admin Setting.
5. When the login message appears, enter password. Touch the password
input area, then the question marks appears. Use the number keypad on
the control panel to enter the password. Once the password is entered,
press OK. (Factory setting:1111)
6. Press the Setup tab > Network Setup.
7. Select TCP/IP Protocol.
• Apple Talk Protocol: This protocol is widely used in Macintosh
network environments.
• Ethernet Speed: You can select the communication speed for
Ethernet connections.
8. Press IP Setting.
9. Select Static and then enter IP Address, Subnet Mask and Gateway
address fields. Touch the input area then, enter addresses by number
keypad on the control panel.
Contact the network administrator if you are not sure how to configure.
10. Press OK.
26 _Getting Started
http://developer.apple.com/networking/
You can also set up the network settings through the network
administration programs.
• SyncThru™ Web Admin Service: Web-based printer
management solution for network administrators. SyncThru™
Web Admin Service provides you with an efficient way of
managing network devices and lets you remotely monitor and
troubleshoot network machines from any site with corporate
internet access. Download this program from
solution.samsungprinter.com.
• SyncThru™ Web Service: Web server embedded on your
network print server, which allows you to:
- Configure the network parameters necessary for the machine to
connect to various network environments.
- Customize machine settings.
- Customize email settings and set up address book for scanning
to email.
- Customize server settings and set up address book for scanning
to the FTP or SMB servers.
- Customize printer, copy, and fax settings
• SetIP: Utility program allowing you to select a network interface
and manually configure the IP addresses for use with the TCP/IP
protocol. See "Using the SetIP program" on page 30.

SYSTEM REQUIREMENTS

Before you begin, ensure that your system meets the following
requirements:

Windows

REQUIREMENT (RECOMMENDED)
OS
CPU
Windows 2000 Pentium II 400 MHz
(Pentium III 933 MHz)
Windows XP Pentium III 933 MHz
(Pentium IV 1 GHz)
Windows Pentium III 933 MHz
(Pentium IV 1 GHz)
Server 2003
Windows Pentium IV 3 GHz
Windows Pentium IV 1 GHz
Server 2008 (Pentium IV 2 GHz)
Windows 7 Pentium IV 1 GHz 32-
bit or 64-bit processor
or higher
• Support for DirectX 9 graphics with 128 MB
memory(to enable the Aero theme).
• DVD-R/W Drive
Windows Pentium IV 1
GHz(x86) or
Server 2008
1.4GHz(x64)
R2
processors(2GHz or
faster)
http://
FREE HDD
RAM
SPACE
64 MB 600 MB
(128 MB)
128 MB 1.5 GB
(256 MB)
128 MB 1.25 GB to
(512 MB) 2 GB
512 MB 15 GB
(1024 MB)
512 MB 10 GB
(2048 MB)
1 GB 16 GB
(2 GB)
512 MB 10 GB
(2048 MB)