AUDIO TELEX TX3010 Installation Instructions

TX3O1O
VOICE OPERATED MUTING MODULE
I
NSTALI-ATION
I
NSTRUCTIO
N
S
Thank
you
for choosing
an
Audio
Telex
TX30l0
voice operated mute
module.
The
TX30l0
allows
for muting of
background music
sources
such. as
a CD player or
cassette deck when a signal is
detected at the microphone
input Ch.
l,
(which is usually the
paging
microphore input)
and also Ctr. 2 on the AT series. Installation
into any Audio
Telex
manuhcttned mixer
or
amplifier
is made
simpti
by utilising a
standard
'end' qrpe
connector
plug, supplied on the module and a
receptacle,
already installld into the mixer
gr
amplifier.
Please
follow
these easy instnrctions for
installatiqr.
g
The installation of the TK30l0
involves rccess
to
the inside of
the amplifiers
or mirers.
Installation should onty
bc
attempted by
a
qualified technician. Always
turn
oIT
the
AC
power and
r:move
thc AC powcr cord before attempting
to
rccess
the inside
of
these
products.
Pleasc
coottct your
nearest Audio Telcx oftice
for details of your oetrest
qualilied
technician"
For installatlon into an lC30 amplifier:
Locate the
5
pin 'end'
connector fountl on
the
mixer
PCB
in
berween the input
gain
pots for Ch. I
and
Ch.
2.
Remove the
tiller plug
and
discard.
Connect
the module to this
receptacle.
ensuring that the wires from
the
connector exit towards
the
rear of the empliticr.
For lnstallatlon lnto an AT SERIES amplifler:
Locate the 5
pin'end'connector
found on the mixer PCB at the rear of
the
input gain pot for Ch.
l.
Remove the
fillcr plug
and
discard.
Connect the mo<Iule to
this
receptacle, ensuring that the wires from
the
connector exit towards
the
right
hand side
of
the
amplifier whcn looking
from the front
panel. {For
installarion ir,to eittrer
an
ATl20R
or
AT|2ORC the
5 pin 'end'
connector
is
found below the nrncr
tr
srssene module (whichever is to the left
hand side
of
the
amplifier)). Note: ort
the
AT
series
the
TX30l0
mo<Iule is designed to
operate so that either input
channels
I
and/or
2 wilt
mure
channels
3
and.l.
For
lnstallatlon lnto
an
SA SERIES ampllfler:
Locate the
I
pin
'end'
connector found
on the
mixer
PCB berween input gain
pots
for
Ch. 2
and Ch. 3 on the mixer
PCB. This 'end'
connector is divided into two
sepamte parts consisting
of 5
pins -d
3 p-inr.
Remove the 5 pln filler plug
anC
discard.
Connect the mcdule
tc
this
receptacle, ansgring
that the wires from the
connector exir
towards
thc right
hand side of thc amplifier whcn looking from
the
front
panel.
For lnstallatlon lnto a TX6000
or
TX8000 mlxer:
Locate
the 8
pin 'end'
connector found
on the
mixer pCB behind
ttre
input gain pot
for Ch.
I
on ttre mixer PCB. This 'cnd' connertor
is divided into
rwo
separate
parts consisting of 5
pins and
3 pins.
Remove the
-5
nin filler plug
and discard.
Connect
the module to this receptaclg ensgring
that the wires &om the
connector exit
towards
the
right
hand side of
the
mixcr
when looking from
the front panel.
ConnecUon to ampllfier:
Connections
White
=
Output
Yellow
=
lnput
Red
=
DC Supply
(Min. I2VDC, Ma:c
ISVDC)
Black
=
Ground
Purple
=
Sigrral
Detection
Notes
Trlm
Pot
Note that
dtq
tirn
pot
tocat€d on the module adjusts
the
sensitivity of
the
incoming
signal to
the
TX30l0.
kr
other words,
how loud tre
incoming
signal needs to be for
suitable atenuation of the background music -*"".
TX8200:
This module
is
not suitable
fc
installation into
the
fi8200
mixer.
Pleasc refer
to
the TX3028
mute
module.
C c'
t',
Ivr
tJ
N
I C
A f
I
O
N S
.
, .
,'