Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
The vehicle identification number (VIN) is located near the left front corner of the windshield. The VIN is visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information VIN LOCATION Disclosure Label affixed to a window on your vehicle.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....11 Ignition Key Removal ....11 Key-In-Ignition Reminder .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Liftgate ......26 Occupant Restraints .....27 Lap/Shoulder Belts .
Page 11: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. Vehicle Key The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer.
Page 12: Key-In-Ignition Reminder
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Refer to Personal Settings in the electronic vehicle infor- mation center (EVIC) Section of this manual for details. WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured.
Page 13: Replacement Keys
The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked. During normal operation, the Theft Alarm/ Immobilizer Light will come on for three (3) seconds immediately after the ignition switch is turned on for a bulb check.
Page 14: Customer Key Programming
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure.
Page 15: General Information
General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undes- ired operation.
Page 16: Power Door Locks
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 17 Automatic Door Locks The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The Auto Lock feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4.
Page 18: Child Protection Door Lock
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system. WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 19: Remote Keyless Entry
REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors, or activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
Page 20: To Lock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Information Center (EVIC). Refer to “Turn Headlamps on with Remote Key Unlock” under “Personal Settings” in the Electronic Vehicle Information Center (EVIC) section of this manual for details. NOTE: The system can also be programmed to unlock all doors on the first press of the UNLOCK button.
Page 21: Transmitter Battery Service
• This device must accept any interference received, including interference that may cause undesired op- eration. If your Remote Keyless Entry transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years.
Page 22: Vehicle Theft Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE THEFT ALARM This system monitors the vehicle doors and ignition switch for unauthorized entry or operation. When the alarm is activated, the system provides both audible and visual signals. The horn will pulse, headlights/park lights will flash, the Vehicle Theft Alarm/Immobilizer light, located in the instrument cluster will flash, and the vehicle will not start.
Page 23: Windows
• The system remains armed during liftgate entry. If someone enters the vehicle through the liftgate and opens any door the alarm will sound. • When the system is armed, the doors can not be unlocked from the interior power door lock switches. The Vehicle Theft Alarm system is designed to protect your vehicle, however, you can create conditions where the system will give you a false alarm.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors. When the lock switch is pressed the window controls on the passenger doors will not illuminate and the passen- ger windows will be disabled.
Page 25 To close the window part way, lift the window switch to the first detent and release when you want the window to stop. The power window switches remain active for 10 min- utes after the ignition switch has been turned off. The time is customer programmable through the electronic vehicle information center (EVIC).
Page 26: Liftgate
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 27: Occupant Restraints
WARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed.
Page 28: Lap/Shoulder Belts
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 29 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 31 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE activated. To reset this feature you must let all of the belt webbing return into the retractor. You will not be able to pull out more webbing until all of the webbing has been returned back into the retractor.
Page 33: Pretensioners
Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belts in the event of a collision. These devices improve the performance of the seat belt system by assuring that the belt is tight about the occupant in a collision.
Page 34: Automatic Locking Mode - If Equipped
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt.
Page 35: Seat Belt Extender
Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if so equipped) is in its lowest position, your dealer can provide you with a seat belt extender.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle may also be equipped with left and right side curtain airbags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with side curtain airbags, they are located above the side windows.
Page 37 Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instru- ment panel knee bolsters to provide improved protection for the driver and front passenger. Left and right side curtain airbags also work with seat belts to improve occupant protection.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint.
Page 39 • PASS AIRBAG OFF Readiness Light • Front Impact Accelerometer sensors • Side Impact Accelerometer sensors • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters The side curtain airbag system, on vehicles so equipped, consists of the following: •...
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
Page 41 you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Side Airbag System The airbag control module determines if a side collision is severe enough to require the airbag to inflate. The control module receives the level of collision severity from the side impact sensors.
Page 43 Occupant Classification System • The Occupant Classification System (OCS) is part of a Federally regulated safety system required for this vehicle. It is designed to turn off the front passenger airbag in the unlikely event that a rear-facing infant seat is in the front passenger seat. NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. Passenger Airbag Front Passenger Disable (PAD) Seat Occupant Indicator Light Adult Grocery Bags, Heavy Briefcases and Other Relatively Light...
Page 45 If the is a fault present in the OCS, the Airbag Warning Light (a red light located in the center of the instrument cluster directly in front of the driver) will be turned on. This indicates that you should take the vehicle to an authorized dealer.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The bags fully inflate in about 50 - 70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger.
Page 47 WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. THIS COULD RESULT IN DEATH OR SERIOUS INJURY TO THE FRONT SEAT PASSENGER IF THE VE- HICLE IS INVOLVED IN AN ACCIDENT.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) In the event of an airbag deployment, your vehicle is designed to record up to 2-seconds of specific vehicle data parameters (see list below) in an event data recorder prior to the moment of airbag deployment.
Page 49 Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • Time of airbag deployment (in terms of ignition cycles and vehicle mileage) •...
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the right seat for your child.
Page 51 Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat.
Page 53 rear-seating positions or if your child restraints are not LATCH-compatible, install the restraints using the vehi- cle’s seat belts. LATCH Anchorages Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next attach the lower hooks or connectors over the top of the seat cover material.
Page 55 installed. Refer to the Automatic Locking Mode section for details. A locking clip should not be necessary once the automatic locking feature is enabled. Position the shoulder and lap belt on the child restraint. The auto- matic locking retractor is activated by first attaching the child seat, then pulling all of the webbing out of the retractor, then allowing back in.
Page 56: Engine Break-In Recommendations
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Attach the tether strap hook of the child restraint to the tether anchor and remove slack in the tether strap according to the child restraint manufacturer’s instruc- tions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
Page 57: Safety Tips
SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Page 58: Periodic Safety Checks You Should Make Outside The Vehicle
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked.
Page 59: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......63 Inside Day/Night Mirror ....63 Automatic Dimming Inside Mirror —...
Page 60 60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support ..... . .87 Heated Seats—If Equipped ....87 Head Restraints .
Page 61 Electronic Speed Control ....104 To Activate ......104 To Set At A Desired Speed .
Page 62 62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Power Outlets ....116 Electrical Outlet Use With Engine Off ..119 Cupholders .
Page 63: Mirrors
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. Adjusting Rearview Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 64: Driver's Side Outside Mirror Auto Dimmer - If Equipped
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer — If Equipped The driver’s side outside mirror automatically adjusts for annoying headlight glare from vehicles behind you.
Page 65: Power Remote-Control Mirrors
Power Remote-Control Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror, or off position. After selecting a mirror move the knob in the same direction you want the mirror to move.
Page 66: Hands-Free Communication (Uconnect™) - If Equipped
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g., Call Mike Work or Dial 248-555-1212 ).
Page 67: Operation
UConnect™ Switches The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. If your cellular phone supports a different profile (eg., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.
Page 68 To complete the pairing process, you will need to reference your cellular phone owner’s manual. One of the following vehicle specific websites may also provide detailed instructions for pairing with the brand of phone that you have: NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect...
Page 69 The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing. • When prompted, after the voice on beep, say Pair a Phone.
Page 70 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For example, you can say 234-567-8901. The phone number that you enter must be of valid length and combination. The UConnect™ limits the user from dialing invalid combination of numbers. For example, 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits.
Page 71 • When prompted, enter the number designation (e.g.: Home, Work, Mobile, or Pager ). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the...
Page 72 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Phonebook Delete. • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete.
Page 73: Phone Call Features
Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the features that you have.
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched.
Page 75: Uconnect™ System Features
until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™...
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA/ Canada and 060 for Mexico). The number called may not be applicable with the available cellular service and area. The UConnect™...
Page 77 You can use your UConnect™ system to access a voice- mail system or an automated service, such as, paging service or automated customer service. Some services require immediate response selection, in some instances, that may be too quick for use of UConnect™ system. When calling a number with your UConnect™...
Page 78: Advanced Phone Connectivity
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system. The UConnect™ system will work the same as if you dial the number using voice recognition. NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™...
Page 79 Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively connected with one electronic device at a time. If you would like to connect or disconnect the Blue- tooth™...
Page 80: Things You Should Know About Your Uconnect™ System
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing. • At the next prompt, say Delete. • The phone names (along with priority numbers) will be played.
Page 81 • It is not recommended to store similar sounding names in the UConnect™ phonebook. • UConnect™ phonebook name tag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • You can say O (letter O ) for 0 (zero). 800 must be spoken eight-zero-zero.
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 83 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 85: Seats
North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
Page 86: Power Reclining Seats
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 87: Lumbar Support
Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever for- ward to increase and rearward to decrease the desired amount of lumbar support. Lumbar Support Control Lever Heated Seats—If Equipped Heated seats, which are available only with leather upholstery, provide comfort and warmth on cold days and can help soothe sore muscles and backs.
Page 88: Head Restraints
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off. When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated.
Page 89: Folding Rear Seat
Folding Rear Seat Folding Rear Seats The rear seatbacks can be folded forward to provide an additional storage area. Pull on the loops shown in the illustration to fold down either or both seatbacks. These loops can be tucked away when not in use. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 When the seat back is folded to the upright position make sure it is latched by strongly pulling on the top of the seat...
Page 90: Adjustable Pedals - If Equipped
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
Page 91: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First, pull the hood release lever located under the left side of the instrument panel. Hood Release Lever Next, move to the outside of the vehicle and push the safety catch to the left.
Page 92: Lights
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the...
Page 93: Headlight Switch
Dimmer Control The dimmer control is part of the headlamp switch, and is located on the left side of the instrument panel. With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the in- strument panel lights.
Page 94: Multi-Function Lever
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Lever The multi-function lever controls the operation of the turn signals, headlight beam selection, and passing lights. The lever is located on the left side of the steering column. Multi-Function Lever Headlights, Parking Lights, Instrument Panel Lights Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
Page 95: Daytime Running Lights (Canada Only)
Daytime Running Lights (Canada Only) The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is on, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving.
Page 96: Highbeam/Lowbeam Select Switch
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE partially up or down without moving beyond the detent. Releasing the lever at the detent will provide 3 flashes. If either light has a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective or there may be a circuit failure.
Page 97: Windshield Wiper Operation - Rear
first detent position, then turn the end of the lever to select the desired delay interval. There are 6 possible delay wiper positions. The delay can be regulated from a maximum of approximately 23 seconds between cycles, to a cycle every second. Mist Feature Push the wiper lever in to activate a single wipe to clear off road mist or spray from a passing vehicle.
Page 98: Adding Washer Fluid
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermittent inter- val previously selected. If the lever is pushed while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF.
Page 99: Tilt/Telescoping Steering Column
TILT/TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. To tilt the column move the steering wheel up or down as desired. To lengthen or shorten the steering column pull out or push in the steering wheel.
Page 100: Tcs (Traction Control System)
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System” in Section 5 of this manual for more information about ABS. TCS (Traction Control System) This system monitors the amount of wheel spin of each of the driven wheels.
Page 101 ESP/TCS Indicator Light The yellow ESP/TCS Indicator Light located in the instrument cluster comes on when the ignition switch is turned to the “ON” position. The light should go out with the engine run- ning, unless the system has been turned off. The ESP/ TCS Indicator Light starts to flash as soon as the tires lose traction and the ESP system becomes active.
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Partial ESP This mode is entered by momentarily pressing the ESP OFF button. When in Partial ESP mode, the TCS portion of ESP has been disabled, and the ESP/ TCS Indicator Light will be illuminated. This mode is intended to be used to for a more spirited driving experience, or if the vehicle is in deep snow, sand or gravel conditions and more wheel spin than ESP...
Page 103: Esp/Bas Warning Lamp
engine torque to be applied to the wheel that is not spinning. To improve the vehicle’s traction when driv- ing with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the Partial ESP mode by pressing the ESP OFF button.
Page 104: Electronic Speed Control
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The ESP/TCS Indicator Light and the ESP/BAS Warn- ing Lamp comes on momentarily each time the igni- tion switch is placed the ON position. • Each time the ignition switch is placed in the ON position, the ESP System will be ON even if it was turned off previously.
Page 105: To Set At A Desired Speed
On some models an indicator light will illumi- nate in the instrument cluster when the elec- tronic speed control is active. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident.
Page 106: To Accelerate For Passing
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while speed control is set, push the lever down and hold (“COAST”). Release the lever when the desired speed is reached, and the new speed will be set. Pushing down and releasing the lever (“COAST”) once will result in a 1 mph (2 km/h) speed decrease.
Page 107: Overhead Console - If Equipped
OVERHEAD CONSOLE — IF EQUIPPED The overhead console contains courtesy/reading lights, an optional universal garage door opener (HomeLink ), storage for sunglasses, and optional power sunroof switches. Overhead Console UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights.
Page 108: Garage Door Opener - If Equipped
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Page 109 The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display which includes HomeLink system messages. The EVIC is located in the instrument cluster below the speedometer. Electronic Vehicle Information Center 1. Press and hold the two outer HomeLink buttons, and release only when the EVIC display shows “Channels Cleared”...
Page 110 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
Page 111: Canadian Programming/Gate Programming
complete the programming of a rolling code equipped device (most common garage door openers require this step). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the learn or smart button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.
Page 112: Using Homelink
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE display will show “Channel X Trained” (where X is Channel 1, 2, or 3). Proceed with Programming step four to complete. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e.
Page 113: Power Sunroof - If Equipped
This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interference that may cause undes- ired operation.
Page 114: Opening Sunroof - Express
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
Page 115: Pinch Protect Override
Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed.
Page 116: Ignition Off Operation
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. This feature is programmable through the Electronic Vehicle Informa- tion Center (EVIC).
Page 117 NOTE: If desired, the power outlet next to the ash tray receiver (if equipped) can be converted by your autho- rized dealer to provide power with the ignition switch in the LOCK position. Front Power Outlet UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 The center console outlet is powered directly from the battery (power available at all times).
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The auxiliary outlet is also powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. Auxiliary Power Outlet...
Page 119: Electrical Outlet Use With Engine Off
Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 120: Rear Seat Cupholders
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cup holders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupants’...
Page 121: Cargo Management System - If Equipped
Cargo Management System — If Equipped The cargo area has an upper and lower load floor. Additional innovative features in the cargo area are the two molded-in bins in the quarter trim panels. Each bin that hold a gallon of milk and a 2-liter bottle of pop. A cargo management system that stores on the lower load floor below the bi-level cargo floor is optional.
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The load floor can be placed in a partially or fully folded position, a flat position, or it can be removed. Use the handle to adjust the position of the load floor. The load floor positions are shown in the following illustrations.
Page 123 Load Floor Fully Folded Rollaway Tonneau Cover — If Equipped The tonneau cover consists of a standard, removable rollaway tonneau cover that is mounted in the rear cargo area behind the seats. Notches in the trim panels close to the liftgate secure the extended cover in place to keep items out of sight.
Page 124 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next pull the tonneau cover using the handle and insert the rear posts by following the guides along each side of the rear compartment making sure the cover is fully seated. Rear Attachment Points Waterproof Liner The optional waterproof liner can be placed over the lower load floor.
Page 125 Cargo Organizer The optional cargo organizer can also be placed into the lower load floor. Lift the handle and pull to open the cargo organizer. Cargo Organizer Handle UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Cargo Tie-Down Hooks The tie-downs located on cargo area floor and on the rear trim panels should be used to safely secure loads when vehicle is moving.
Page 126 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
Page 127: Roof Luggage Rack - If Equipped
ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over both luggage rack crossbars. Roof Luggage Rack Distribute cargo weight evenly on the roof rack crossbars.
Page 128: Load Leveling System - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. •...
Page 129: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....132 Instrument Cluster ..... 133 Instrument Cluster Descriptions .
Page 130 130 UNDERSTANDING YOUR INSTRUMENT PANEL Sales Code RAK – AM/FM/Cassette/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, Video, MP3, And WMA Capabilities ......157 Operating Instructions - Radio Mode .
Page 131 PTY Button Seek ..... 171 Satellite Antenna ..... . 171 Reception Quality .
Page 132: Instruments And Controls
132 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS...
Page 133: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 133 INSTRUMENT CLUSTER...
Page 134: Instrument Cluster Descriptions
134 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Trip Odometer Button Press this button to change the display from odometer to either of the two trip odometer settings.
Page 135 immediate service is required and you may experience reduced performance, an elevated/rough idle or en- gine stall and your vehicle may require towing. The light will come on when the ignition is first turned on and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer.
Page 136 136 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated. If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a chime will sound to alert you to turn the signals off.
Page 137 14. Oil Pressure Warning Light This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
Page 138 138 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
Page 139 22. Tire Pressure Monitor Warning Light — If Equipped This light will turn on continuously when there is a Low tire pressure condition. The light will also turn on if a problem exist with any tire sensor. When a system fault is detected, the indicator lamp will flash repetitively for ten seconds.
Page 140: Electronic Vehicle Information Center (Evic)
140 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Low Fuel Indicator Light The Low Fuel Light will turn on when there is approximately 2 gallons (9 liters) of fuel remain- ing in the tank. This light will remain on until fuel is added. 25.
Page 141 equipped with steering wheel mounted switches (de- scribed in this section) will also be equipped with the EVIC. The EVIC consists of the following: • System Status • Vehicle information warning message displays • Tire Pressure Monitor System • Personal Settings (customer programmable features) •...
Page 142 142 UNDERSTANDING YOUR INSTRUMENT PANEL FM to Tape to CD, or to Satellite (SAT) depending on which radio is in the vehicle. This button can also be used to return to a previous navigation menu selection. When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages.
Page 143: Trip Functions
• Right Front Low Pressure (with a single chime). Refer to “Starting And Operating, Tire Section” • Right Rear Low Pressure (with a single chime). Refer to “Starting And Operating, Tire Section” • Check TPM System (with a single chime). Refer to “Starting And Operating, Tire Section”...
Page 144: Compass Display
144 UNDERSTANDING YOUR INSTRUMENT PANEL currently being displayed. To reset all resettable func- tions, press and release the FUNCTION SELECT button a second time within 3 seconds of resetting the currently displayed function (>Reset ALL will be displayed during this 3 second window). Compass Display Press and release the compass button to dis- play one of eight compass readings to indicate...
Page 145: Telephone - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 145 To set the variance: Turn the ignition switch ON. Press and hold the compass button for approximately 2 sec- onds. Use the SCROLL buttons until “Compass Variance” is highlighted. The “Compass Variance” message and the last variance zone number will be displayed.
Page 146 146 UNDERSTANDING YOUR INSTRUMENT PANEL When the appropriate conditions exist, and if supported by the Cell phone the EVIC will display the following telephone symbols: The EVIC displays this symbol to indicate the signal strength of the U-Connect phone. The number of horizontal bars increase as the strength of the U-Connect phone signal in- Signal...
Page 147: Navigation - If Equipped
The EVIC displays this symbol to indicate that the U-Connect phone is currently not available. Phone Avail- able Navigation — If Equipped Navigation Display Control Press and release the MENU button until Navigation is displayed in the EVIC. When the Navigation System is On, the steering wheel buttons can be used to select the Map or Menu display on the Navigation Unit.
Page 148: Personal Settings (Customer Programmable Features)
148 UNDERSTANDING YOUR INSTRUMENT PANEL Personal Settings (Customer Programmable Features) This allows the driver to set and recall features when the transmission is in PARK. Press and release the MENU button until Personal Set- tings is displayed in the EVIC. Use the SCROLL buttons to display one of the following choices: Language...
Page 149 Remote Unlock Driver’s Door 1st When DRIVER’S DOOR 1ST is selected only the driv- er’s door will unlock on the first press of the remote keyless entry unlock button and require a second press to unlock the remaining locked doors. When REMOTE UNLOCK ALL DOORS is selected all of the doors will unlock at the first press of the remote keyless entry unlock button.
Page 150: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
150 UNDERSTANDING YOUR INSTRUMENT PANEL Turn Headlamps on with Remote Key Unlock When this feature is selected the headlamps will activate and remain on for up to 90 seconds when the doors are unlocked using the remote keyless entry transmitter. Press and release the FUNCTION SELECT button when in this display until “OFF”, “30 sec.”, “60 sec.”, or “90 sec.”...
Page 151: Operating Instructions - Radio Mode
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
Page 152 152 UNDERSTANDING YOUR INSTRUMENT PANEL equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. PSCAN Button (Radio Mode) Pressing the PSCAN button, causes the tuner to scan through preset stations, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each preset station before continuing to the next.
Page 153 Press the rotary TUNE control a third time and TREB will be displayed. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL will be displayed.
Page 154: Operation Instructions - Cd Mode
154 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up.
Page 155: Operation Instructions - Auxiliary Mode
TIME Button (CD Mode) Press this button to change the display from elapsed CD playing time to time of day. The time of day will be displayed for 5 seconds. RW/FF (CD Mode) Press and hold the FF (Fast Forward) and the CD player will begin to fast forward until FF is released.
Page 156: Operating Instructions - Hands Free Phone - If Equipped
156 UNDERSTANDING YOUR INSTRUMENT PANEL MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. MUTE will be displayed. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers.
Page 157: Sales Code Rak - Am/Fm/Cassette/Cd
SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. RAK Radio UNDERSTANDING YOUR INSTRUMENT PANEL 157 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 158 158 UNDERSTANDING YOUR INSTRUMENT PANEL Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection. Holding the button and will bypass stations without stopping until you release it.
Page 159 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 160: Operating Instructions - Tape Player
160 UNDERSTANDING YOUR INSTRUMENT PANEL Top 40 Country Oldies Soft Nostalgia Jazz Classical Rhythm and Blues Rhythm_and_Blues Soft Rhythm and Blues Foreign Language Foreign_Language Religious Music Religious_Music Religious Talk Personality Public College Unassigned Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Page 161: Seek Button
Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc.
Page 162: Noise Reduction
162 UNDERSTANDING YOUR INSTRUMENT PANEL Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise reduction System: Press Preset 1 after you insert the tape. The NR light in the display will go off when the Dolby System is off.
Page 163: Load/Eject Button (Cd Mode For Cd Audio Play)
SCAN Button (CD MODE for CD Audio Play) Press the Scan button to scan through each track on the CD currently playing. LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJT button and the push- button with the corresponding number where the CD is being loaded.
Page 164: Notes On Playing Mp3 Files
164 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
Page 165 files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 •...
Page 166: Operation Instructions
166 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
Page 167 The radio display will show LOADING DISC when the disc is loading. LOAD / EJT - Eject Press the LOAD/ EJT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal.
Page 168: Satellite Radio - If Equipped
168 UNDERSTANDING YOUR INSTRUMENT PANEL Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder. Buttons 1 - 6 (CD Mode for MP3 Play) Selects disc positions 1 - 6 for Play/Load/Eject. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s...
Page 169: Electronic Serial Number/Sirius Identification Number (Esn/Sid)
Electronic Serial Number/Sirius Identification Number (ESN/SID) The Electronic Serial Number/Sirius Identification Num- ber is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With REF Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and Time buttons simultaneously for 3 seconds.
Page 170: Selecting A Channel
170 UNDERSTANDING YOUR INSTRUMENT PANEL A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down.
Page 171: Pty Button Seek
PTY Button SEEK When the desired program is obtained, press the SEEK button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location.
Page 172: Remote Sound System Controls
172 UNDERSTANDING YOUR INSTRUMENT PANEL selecting a variety of destinations and routes. The unit also provides an AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
Page 173: Radio Operation
The FUNCTION SELECT button advances the radio to the next preset, changes the tape side being played, or changes the current disc when used in audio mode. The SCROLL buttons change selections such as radio station, CD track, or satellite radio chan- nel depending on the current mode.
Page 174: Radio General Information
174 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning.
Page 175: Cassette Tape And Player Maintenance
CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly dimin- ished. 2. Keep the cassette tape in its case to protect from slackness and dust when it is not in use.
Page 176: Radio Operation And Cellular Phones
176 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Do not store the disc where temperatures may become too high. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio.
Page 177 Electric Rear Window Defroster Press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An LED in the button will illuminate to indicate the rear window defroster is ON. The defroster automatically turns off after about 10 minutes of opera- tion.
Page 178 178 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Selection The mode selector (the right rotary knob) can be placed in several posi- tions. Dots between each of the mode selections identify intermediate modes that allow the occupants to fine tune airflow distribution. Defrost Air is directed to the windshield through the outlets at the base of the windshield.
Page 179: Automatic Temperature Control - If Equipped
is re-used. Use this mode to rapidly cool the inside of the vehicle. The Recirculation mode can also be used to temporarily block out outside odors, smoke, and dust. Window Fogging Interior fogging on the windshield can be quickly re- moved by turning the mode selector to Defrost.
Page 180 180 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the system is quite simple. Begin by turning the right mode knob to AUTO, and place the blower control (left knob) to either LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occu- pants only.
Page 181 • On vehicles equipped with diesel engines the blower fan will initially operate at a minimum speed to provide you with maximum comfort in the fan auto- matic mode during cold weather start-ups. Then, as the engine warms up the fan will gradually increase its speed.
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL...
Page 183 The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the following positions. • Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles.
Page 184: Summer Operation
184 UNDERSTANDING YOUR INSTRUMENT PANEL the rear window defroster is ON. The defroster automati- cally turns off after approximately 10 minutes of opera- tion for the first push of the button, and will turn off after approximately 5 minutes for the second push of the button.
Page 185: Winter Operation
Winter Operation Use of the air Recirculation mode during winter months is not recommended because it may cause window fogging. NOTE: See Operating Tips chart (for Manual A/C Control) at the end of this section for suggested control settings in different weather conditions. Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e.
Page 186: Operating Tips
186 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 187: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....190 Normal Starting ..... . 190 Transmission Shifting .
Page 188 188 STARTING AND OPERATING Life Of Tire ......219 Replacement Tires ..... 220 Alignment And Balance .
Page 189 Trailer Towing ......237 Common Towing Definitions ... . . 237 Trailer Hitch Classification .
Page 190: Starting Procedures
190 STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather;...
Page 191 WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Un- burned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 192: Transmission Shifting
192 STARTING AND OPERATING After Starting The idle speed will automatically decrease as the engine warms up. TRANSMISSION SHIFTING 5 Speed Automatic Transmission Gear Selector WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running.
Page 193 Park Position The PARK position is to be used when parking the vehicle. Engage only with the vehicle stopped. The PARK position is not intended to serve as a brake when the vehicle is parked. Rather, the driver should always use the parking brake in addition to placing the selector lever in PARK to secure the vehicle.
Page 194 194 STARTING AND OPERATING Neutral No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage in NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads).
Page 195 NOTE: To avoid overrevving the engine when the selector lever is moved in “D -” direction, the transmis- sion will not shift to a lower gear if the engine’s revolu- tions per minute limit would be exceeded. Briefly press the selector lever in the “D +” direction. The transmission will shift from the current gear to the next higher gear.
Page 196 196 STARTING AND OPERATING A reset feature is available to allow the vehicle to be driven to a dealer for service. To reset the transmission, use the following procedure: 1. Stop the vehicle. 2. Move the selector lever to the PARK position. 3.
Page 197: Automatic Transmission - General Information
Automatic Transmission — General Information CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 198 198 STARTING AND OPERATING self-calibrating. Therefore, the first few shifts on a new vehicle may be somewhat abrupt or soft until after the break-in period. This is a normal condition, and pre- cision shifts will develop within a few shift cycles. WARNING! It is dangerous to shift the selector lever out of PARK or NEUTRAL if the engine speed is higher than idle...
Page 199: Autostick
Brake Transmission Shift Interlock System This vehicle is equipped with a brake transmission shift interlock system (BTSI) that holds the gearshift lever in the P (Park) position when the ignition switch is in the LOCK position. To move the gear selector lever out of the P (Park) position, the ignition switch must be turned to the ON position, and the brake pedal must be depressed.
Page 200: Autostick General Information
200 STARTING AND OPERATING An UPSHIFT message will appear in the Electronic Vehicle Information Center (EVIC) portion of your instru- ment cluster when using Autostick. This message ap- pears in order to alert the driver to upshift to the next gear.
Page 201: Parking Brake
PARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position.
Page 202: Brake System
202 STARTING AND OPERATING The parking brake should always be applied when the driver is not in the vehicle. WARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever.
Page 203 The electronic brake force distribution (EBD) prevents the rear wheels from over-braking and provides greater control of available braking forces applied to the rear axle. WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer.
Page 204 204 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake Sys- tem. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 205: Power Steering
WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interfer- ence can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
Page 206: Tire Safety Information
206 STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
Page 207 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
Page 208 208 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
Page 209 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 210: Tire Identification Number (Tin)
210 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 211: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location STARTING AND OPERATING 211 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the:...
Page 212 212 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 213 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and STARTING AND OPERATING 213...
Page 214 214 STARTING AND OPERATING...
Page 215: Tires-General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 216: Tire Inflation Pressures
216 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 217 CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 218: Radial-Ply Tires
218 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Page 219: Tread Wear Indicators
Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 220: Replacement Tires
220 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators).
Page 221: Alignment And Balance
CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear.
Page 222 222 STARTING AND OPERATING The Tire Pressure Monitoring System consists of the following components: • Receiver Module • 4 Wheel Sensors • Amber Colored Tire Pressure Monitoring Indicator Lamp NOTE: For vehicles with optional wheel/tire sizes and significantly different tire placard pressures, the placard pressure value and the low-pressure threshold value is re-programmable at your authorized dealer to accommo- date the customer selected wheel/tire combinations rec-...
Page 223: Tire Pressure Monitoring - Premium System
NOTE: • The TPM system can inform the driver of a low tire pressure condition. • The TPM system is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • The TPM system should not be used as a tire pressure gauge while adjusting your tire pressure.
Page 224 224 STARTING AND OPERATING Modules mounted in three of the four wheel wells, various Tire Pressure Monitoring System Display Mes- sages in the EVIC, and an amber colored Indicator Lamp. NOTE: For vehicles with optional wheel/tire sizes and significantly different tire placard pressures, the placard pressure value and the low-pressure threshold value is re-programmable at your authorized dealer to accommo- date the customer selected wheel/tire combinations rec-...
Page 225: General Information
CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sen- sor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Page 226: Tire Chains
226 STARTING AND OPERATING TIRE CHAINS If driving conditions require tire chains for your vehicle, chains that meet SAE class “S” requirements can be used, but they must be installed on 245/45ZR20 size tires. Contact your local dealership or tire dealer for these tire sizes.
Page 227: Snow Tires
NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed.
Page 228: Tire Rotation - All Season Tires
228 STARTING AND OPERATING Tire Rotation — All Season Tires The suggested rotation method for vehicles equipped with all season tires is the “forward-cross” shown in the following diagram. Tire Rotation — General Information Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions.
Page 229: Ground Clearance
If you experience these symptoms, try another brand of “premium” gasoline before considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 230: Reformulated Gasoline
230 STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline”. Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of reformulated gaso- lines.
Page 231: Materials Added To Fuel
content of gasoline may not be indicated on the pump, you should ask your gasoline retailer whether or not his/her gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States.
Page 232: Carbon Monoxide Warnings
232 STARTING AND OPERATING • The use of fuel additives which are now being sold as octane enhancers are not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives are not the responsibility of the manufacturer.
Page 233: Adding Fuel
ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. Push in on the left side (near the edge) of the fuel filler door to access the fuel filler cap. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
Page 234 234 STARTING AND OPERATING NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. If the gas cap is not secured properly the Malfunction Indicator Light in the instrument cluster will turn on.
Page 235: Vehicle Loading
VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow. This information should be used for passenger and luggage loading as indicated. If the seatbacks are folded for carrying cargo, do not exceed the specified GVWR and GAWR. Vehicle Certification Label Your vehicle has a certification label attached to the rear of the driver’s door.
Page 236: Overloading
236 STARTING AND OPERATING Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation.
Page 237: Trailer Towing
Front Axle Empty Weight 2054 lbs (932 kg) Load (Including driver, pass- 271 lbs sengers and cargo) (123 kg) Total 2325 lbs (1055 kg) GAWR 2546 lbs (1155 kg) TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Page 238 238 STARTING AND OPERATING Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its loaded and ready for operation condition. The recom- mended way to measure GTW is to put your fully loaded trailer on a vehicle scale.
Page 239: Trailer Hitch Classification
Weight-Distributing Hitch A weight-distributing hitch includes a receiver attached to the tow vehicle, plus a removable hitch head and spring bar assembly that fits into the receiver opening and hook up brackets that connect the spring bars to the trailer frame. Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional...
Page 240 240 STARTING AND OPERATING Engine/Transmission 6.1L Automatic 40 SQ. FT. (3.72 square 40 SQ. FT. (3.72 square 40 SQ. FT. (3.72 square 40 SQ. FT. (3.72 square Refer to local laws for maximum trailer towing speeds. NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard.
Page 241: Trailer And Tongue Weight
Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer.
Page 242: Towing Requirements
242 STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle driv- etrain components the following guidelines are recom- mended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle.
Page 243 • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. Always, block or chock the trailer wheels. • GCWR must not be exceeded. •...
Page 244 244 STARTING AND OPERATING − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. −...
Page 245: Towing Tips
The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector STARTING AND OPERATING 245 7 - Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
Page 246 246 STARTING AND OPERATING NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance and extend transmission life by reducing exces- sive shifting and heat build up. This action will also provide better engine braking. The automatic transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation.
Page 247: Recreational Towing
Towing Tips — Cooling System To reduce potential for engine and transmission over- heating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. − Highway Driving Reduce speed.
Page 249: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....250 If Your Engine Overheats ....250 TIREFIT Tire Repair .
Page 250: Hazard Warning Flasher
250 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel below the center air outlets. Hazard Flasher Switch To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer- gency.
Page 251 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
Page 252: Tirefit Tire Repair
252 WHAT TO DO IN EMERGENCIES TIREFIT TIRE REPAIR Small punctures, particularly those in the tread, can be sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -4°F (-20°C).
Page 253 WARNING! • Do not attempt to repair a tire on the side of the vehicle close to traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or repairing a tire. • Cuts or punctures larger than approximately 0.16 in.
Page 254 254 WHAT TO DO IN EMERGENCIES 5. Unscrew the valve cap from the valve on the deflated tire. 6. Screw the filler hose (6) from the sealant bottle (5) on the tire valve. 7. Insert the power plug (2) into the power point on the instrument panel.
Page 255: Jump-Starting Procedures If Battery Is Low
• Do not operate the electric air pump for more than eight minutes to avoid overheating. The air pump may be used again once it has cooled down. • Replace the TIREFIT sealant bottle (5) once every four years to assure optimum operation of the system. •...
Page 256 256 WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the en- gine has started, ignite and damage the converter and vehicle.
Page 257: Driving On Slippery Surfaces
of the vehicle with the discharged battery. Make sure you have a good contact on the engine ground. Refer to the following illustration for jump starting connections. Jump Starting 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery.
Page 258: Freeing A Stuck Vehicle
258 WHAT TO DO IN EMERGENCIES partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precau- tions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if road has standing water or puddles. 3.
Page 259: Towing A Disabled Vehicle
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 260: Towing This Vehicle Behind Another Vehicle
260 WHAT TO DO IN EMERGENCIES CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • The only approved method of towing is with a flat bed truck.
Page 261: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 6.1L Engine ......263 Onboard Diagnostic System — OBD II ..264 Emissions Inspection And Maintenance Programs .
Page 262 262 MAINTAINING YOUR VEHICLE Windshield Washers/Headlight Washers ..277 Exhaust System ..... . 277 Cooling System ..... . . 278 Hoses And Vacuum/Vapor Harnesses .
Page 263: 6.1L Engine
MAINTAINING YOUR VEHICLE 263 6.1L ENGINE 6.1L Engine Compartment...
Page 264: Onboard Diagnostic System - Obd Ii
264 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 265: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready...
Page 266: Replacement Parts
266 MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
Page 267: Maintenance Procedures
WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 268 268 MAINTAINING YOUR VEHICLE NOTE: Fill engine oil one quart at a time. Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. CAUTION! Operating the engine with the oil levels below the safe zone, or operating with oil levels that exceed the top of the safe zone may cause engine damage.
Page 269 NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule A of the Mainte- nance Schedules section of this manual.
Page 270: Engine Oil Filter
270 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment.
Page 271: Engine Air Cleaner Filter
Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe con- ditions, the filter element should be inspected periodi- cally and replaced if necessary at the intervals shown on Schedule “B”.
Page 272 272 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 273: Maintenance-Free Battery
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start engine by pushing or towing the vehicle.
Page 274: Air Conditioner Maintenance
274 MAINTAINING YOUR VEHICLE NOTE: The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you.
Page 275: A/C Air Filter - If Equipped
WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information.
Page 276: Power Steering - Fluid Check
276 MAINTAINING YOUR VEHICLE Refer to the “Maintenance Schedules” section of this manual for the recommended air conditioning filter replacement intervals. Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated.
Page 277: Windshield Wiper Blades
underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality Mopar Lock Cylinder Lubri- cant or equivalent directly into the lock cylinder.
Page 278: Cooling System
278 MAINTAINING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
Page 279 Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
Page 280 280 MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 281 Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
Page 282 282 MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 283: Hoses And Vacuum/Vapor Harnesses
Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and exces- sive swelling indicate deterioration of the rubber. Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold.
Page 284: Brake Fluid Level Check
284 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to facilitate the assembly of hoses to couplings.
Page 285: Fuel System Hoses
Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. •...
Page 286: Automatic Transmission
286 MAINTAINING YOUR VEHICLE Automatic Transmission Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level. CAUTION! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration...
Page 287: Front And Rear Wheel Bearings
Front And Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these compo- nents. Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 288 288 MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
Page 289 • Use Mopar touch up paint or equivalent on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar Fabric Cleaner or equivalent to clean fabric upholstery and carpeting. Interior Trim should be cleaned starting with a damp cloth, a damp cloth with a mild detergent, then MOPAR Vinyl Cleaner or equivalent if absolutely necessary.
Page 290: Cleaning The Center Console Cup Holders
290 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Page 291 CAUTION! • When installing the Power Distribution Center cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Power Distribu- tion Center, and possibly result in a electrical system failure.
Page 292 292 MAINTAINING YOUR VEHICLE Cavity Fuse Circuits 20 Amp Auto Shutdown/Powertrain Yellow Control Module (PCM) — — — — 25 Amp Powertrain Control Module Clear 20 Amp Injectors, Ignition Coils Yellow 15 Amp Powertrain Control Module Dk. Blue 30 Amp Antilock Brake System (ABS) Pink Valves...
Page 293: Rear Power Distribution Center
Rear Power Distribution Center There is also a power distribution center located in the rear compartment under an access panel. This center contains fuses and relays. Rear Power Distribution Center MAINTAINING YOUR VEHICLE 293 CAUTION! • When installing the Power Distribution Center cover, it is important to ensure the cover is prop- erly positioned and fully latched.
Page 294 294 MAINTAINING YOUR VEHICLE Cavity Fuse Circuits — — 40 Amp Battery Green 30 Amp Heated Seat/Steering Column Pink 20 Amp Fuel Pump Yellow — — 15 Amp Ignition Start/Run - Start Dk. Blue 20 Amp Console Power Outlet Yellow 10 Amp Rear Fog Lamp —...
Page 295 Cavity Fuse Circuits 10 Amp Curtain Airbag - if equipped 5 Amp Sentry Key/Remote Keyless Orange Entry/Powertrain Control Module Ignition Feed 10 Amp Steering Column Module/ Power Mirrors - if equipped — — — — — — — — 5 Amp Power Antenna/Garage Door Orange Opener/Ignition Delay...
Page 296: Vehicle Storage
296 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e.
Page 297: Bulb Replacement
LIGHT BULBS — Exterior Low Beam Headlamp..... 9006 High Beam Headlamp ....9005 Front Park/Turn Lamp.
Page 298 298 MAINTAINING YOUR VEHICLE • Replace the bulb and push into socket assembly. Reinstall the socket assembly, and turn clockwise. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol.
Page 299: Lamp
Tail/Stop, Turn Signal Lamp, and Backup Lamp 1. Open the liftgate. 2. Remove tail lamp access cover. 3. Push the tail lamp electrical connector locking tab to the side. MAINTAINING YOUR VEHICLE 299 4. Disconnect the electrical connector. 5. Remove 1 wingnut from the back of the tail lamp assembly.
Page 300 300 MAINTAINING YOUR VEHICLE 7. Pull tail lamp assembly clear from vehicle to access bulbs. Turn bulb sockets counter-clockwise to remove. 8. Pull the appropriate bulb to remove it from the socket.
Page 301: License Lamp
9. Replace the bulb, reinstall the socket, and reattach the tail light assembly. 10. Close the liftgate. License Lamp 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly and pull the bulb from the socket.
Page 302: Fluids And Capacities
302 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (approximate) 6.1 Liter Engines (Premium 91 Octane) Engine Oil-With Filter 6.1 Liter Engines (SAE 0W-40) Cooling System * 6.1 Liter Engines (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) or equivalent. * Includes heater and coolant recovery bottle filled to MAX level.
Page 303: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. Engine Oil (6.1 Liter) Use API rated SM/CF full synthetic engine oil. SAE 0W-40 is recommended. Refer to the engine oil viscosity chart for the correct SAE grade meeting DaimlerChrysler Material Standard MS-10725.
Page 305 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..306 Maintenance Schedules ....306 Schedule “B” ......309 Schedule “A”...
Page 306: Emission Control System Maintenance
306 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 307 • Taxi, police, or delivery service (commercial ser- vice). • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual.
Page 308 308 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir and brake master cylinder, and add as needed. •...
Page 309: Schedule "B
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 310 310 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors.
Page 311 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve.
Page 312 312 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors.
Page 313 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner.
Page 314 314 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors.
Page 315 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Replace the spark plugs. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and ten- sioner.
Page 316: Schedule "A
316 SCHEDULE “A” SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the air conditioning filter. Rotate the tires.
Page 317 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner.
Page 318 318 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Replace the spark plugs. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and ten- sioner.
Page 319 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 321: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......322 Prepare For The Appointment .
Page 322: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 323 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center. Any communication to the Manufacturer’s Customer Center should include the following information: •...
Page 324: Warranty Information (U.s. Vehicles Only)
324 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts.
Page 325: Reporting Safety Defects
REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 326 326 IF YOU NEED CONSUMER ASSISTANCE NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles.
Page 327: Department Of Transportation Uniform Tire Quality Grades
DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
Page 328: Temperature Grades
328 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (highest), B, and C, repre- senting the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 329 INDEX...
Page 330 330 INDEX ABS (Anti-Lock Brake) System ... . . 202 Adding Engine Coolant (Antifreeze) ..280 Adding Fuel ......233 Adding Washer Fluid .
Page 331 Location ......256,273 Bearings ......287 Belts, Drive .
Page 332 332 INDEX Compass ......144 Compass Calibration ....144 Compass Variance .
Page 333 Emergency, In Case of Freeing Vehicle When Stuck ... . . 258 Hazard Warning Flasher ....250 Jump Starting .
Page 334 334 INDEX Cooling System ..... . . 279 Engine Oil ......267 Power Steering .
Page 335 Passing ......96 Switch ......93,94 Time Delay .
Page 336 336 INDEX Liftgate ....... 26 Lights ......58,92 Airbag .
Page 337 Schedule A ......316 Schedule B ......309 Malfunction Indicator Light .
Page 338 338 INDEX Pets ........56 Phone, Cellular ......66 Phone, Hands-Free .
Page 339 Safety Checks Outside Vehicle ....58 Safety Defects, Reporting ....325 Safety, Exhaust Gas .
Page 340 340 INDEX Engine Fails to Start ....191 Starting and Operating ....190 Steering Linkage .
Page 341 Spinning ......218 Tread Wear Indicators ....219 Tongue Weight/Trailer Weight .
Page 342 342 INDEX Warnings and Cautions ....6 Warranty Information ....324 Washer, Adding Fluid .
Page 343 NOTES...
Page 344 NOTES...

Dodge 2006 LX Magnum SRT8 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2006 LX Magnum SRT8

Summary of Contents for Dodge 2006 LX Magnum SRT8