SABINE SW75-T BELTPACK TRANSMITTER Quick Setup Manual

SW75-T Beltpack Transmitter Quick Setup Guide
1
Select the INPUT to Match your Input Type
1
SELECT
Select INPUT function: Push the transmitter's
SELECT button to scroll through functions until
the word INPUT appears at bottom in the trans-
mitter LCD, which stays backlit while you are
editing all parameters.
NOTE: Electric Guitar & Bass: For best results, put your receiver's FBX Feedback Exterminator into
BYPASS mode. BYPASS is accessible via the receiver front panel or Remote Software control.
2
Adjust PAD Settings to Match your Input Level
As in all audio equipment, the setting of the input level is crucial to achieving the best sound quality. Setting
minimal PAD levels (-3, -6, or -10 dB) may produce a distorted sound if you are using a high output microphone
or instrument. Conversely, setting a more extreme PAD level (-40, -37, or -34 dB) may require you to raise
your system gain unnecessarily, resulting in a noisier output. Set your level so there are at least three indica-
tors illuminated on the audio meter, with an occasional move to the fourth indicator. The fifth and biggest
indicator denotes clipping. If you see clipping, choose a lower pad setting (for example, go from -10 to -14 dB).
Changing PAD Settings
1
SELECT
Select PAD function: Press the
SELECT button to scroll through
functions until PAD flashes in the
transmitter LCD.
Suggested PAD Settings - adjust for your application
♦ Microphones
low-output
-10 dB
3
Set Low-Cut Filter to Match your Sound
1
SELECT
Select LOW CUT function: Push the
transmitter's SELECT button to scroll through
functions until L 0 or L 75 appears on the transmit-
ter LCD.
4
Battery RUN TIME Hours
1
To view Run-time Hours: Use the
transmitter's SELECT button to scroll
through functions until TIME appears in
the LCD.
PLEASE CAREFULLY READ THE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS
2
DOWN UP
Select PAD setting: Use the UP
or DOWN buttons to select the
desired setting. Selection is
stored after 3 seconds.
♦ SWT73W-TA4
♦ SWT31L-TA4
♦ SWT56W-TA4
Cardioid Lav
♦ Microphones ♦ Electric guitars
standard
♦ Acoustic
♦ Microphones
instruments
low-gain pickups
-17 dB
Resets the display that indicates the length of power-on time (hours and minutes) since the last
battery change or recharge.
MICROPHONE
2
Select INSTR or MIC: Use the UP or DOWN but-
tons to select your desired input (Instrument or
Microphone). This important selection optimizes
the input section of the transmitter. Your selection
is stored after 3 seconds.
♦ SWTVT50-TA4
Omni Lav
♦ SVT40L-TA4
Omni Lav
Cardioid
♦ SVT80BW-TA4
Headworns
♦ SVT81LW-TA4
Cardioid Headworns
♦ Electric guitars
low-gain pickups standard
higher gain
-23 dB -26 to -34 dB
Toggles between no filter and 12 dB/octave low frequency roll-off filter
(starting at 75 Hz).
2
DOWN UP
Select LOW CUT setting: Use the UP or DOWN
buttons to toggle between no filter (indicated in the
display as L 0) or a roll-off at 75 Hz (indicated by L 75).
2
To Reset Run-time hours: Simultaneously press
and hold both the UP and DOWN arrows until LCD
resets to 0.00.
.
DOWN UP
3
Check for Clipping: Make sure
the receiver's Audio Level Meter
stays out of the Clipping Zone.
♦ SVT70LW-TA4
♦ SVT70BW-TA4
Omni
Headworns
♦ Instruments
high-gain pre-
amps
-37 dB
USER TIP:
GUITARS
SOME ACOUSTIC INSTRUMENTS
MAY BENEFIT FROM
DOWN UP
NOTE: -
RUN TIME HOURS ARE RESET AUTOMATICALLY
WHEN CHARGING BATTERIES
LIT-SW75T-QG-EN-070223.pmd
SIDE
A
INSTRUMENT
Clipping
Zone
FOR ELECTRIC
& L0;
BASSES USE
L75.
.