Advertisement
Quick Links
Planet
AC600.2
AC800.4
ACI
200.4
Congratulations
purchase
ANARCHY
It has been designed,
and manufactured
the highest
and quality, and will afford you
years of listening
Thank you for making
Audio your choice
entertainment!
of a Planet
Amplifier.
level of performance
Audio
Two Channel
MOSFET
Amplifiers
Four
Channel
MOSFET
Amplifiers
on your
Audio
engineered
to bring you
pleasure.
Planet
for car audio
Car Audio
Car Audio
Advertisement
Related Manuals for Planet Audio AC600.2
Summary of Contents for Planet Audio AC600.2
- Page 1 Planet Audio AC600.2 Two Channel MOSFET Car Audio Amplifiers AC800.4 Four Channel MOSFET Car Audio 200.4 Amplifiers Congratulations on your purchase of a Planet Audio ANARCHY Amplifier. It has been designed, engineered and manufactured to bring you the highest level of performance...
- Page 2 Introduction With the Planet Audio ANARCHY MOSFET amplifier series, we are introducing eleven new amplifiers, all designed in the USA The 2CH, 4CH ANARCHY models feature variable low pass and high pass crossovers. All amps feature variable input gain controls. For further flexibility in the use of a subwoofer, 0-+18dB...
- Page 3 What is included? When first unpacking your new amplifier, please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the amplifier. • ANARCHY amplifier • High input cable with connector •...
- Page 4 Features Your new ANARCHY amplifier features the following: • Class A-B operation • Bridgeable outputs • Tri-Mode capable • MOSFET PWM (Pulse Width Modulated) Power Supply • 2 Ohm stable stereo operation with output power increase • Thermal and speaker short protection •...
- Page 5 About 2 Ohm operation Your ANARCHY amplifier has been designed to operate efficiently at loads down to 2 Ohms. This means that you can install four 8 Ohm speakers per channel, when using parallel wiring. Increasing the number of woofers per channel at low frequencies (below 1OOHz)produces an acoustic coupling effect.
- Page 6 General precautions Before installing and using your Planet Audio amplifier, please become familiar with infor- mation contained in this manual. Please keep this manual in a safe place for future reference. • Do not open or attempt to repair this unit yourself. Dangerous high voltages are present which may result in electric shock.
- Page 7 Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier.
- Page 8 Connecting the amplifier Before doing any wiring, look through this manual and identify the diagrams to follow for power, input and speaker connections for your particular installation. Be sure you understand all the connections before you proceed. 1. Connect the power ground terminal to the closest point on the chassis of the car.
- Page 9 7 Insert fuse(s) into the battery fuse holder(s). 8. Recheck all connections before powering up the amplifier. 9. Set all level controls to minimum position, and set all crossover controls/switches to the desired frequency points. 10. Power up the head unit and the amplifier.
- Page 10 RCA cable for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time! 2-ChanneI Amplifiers AC600.2 Plenet Audio '"purs To Audio Outputs of head unit or signal processor 4-ChanneI Amplifiers AC800.4...
- Page 11 NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time! 2-ChanneI Amplifiers AC600.2 e Plenet kucJio 'NPUTS BASS LEVEL To Speaker Terminals of head unit 4-ChanneI Amplifiers AC800.4 AC1200.4...
- Page 12 Power and Speaker Wiring 2-ChanneI Amplifiers 2 Channel and Bridged Modes LEFT Speaker RIGHT SPEAKER Speaker IMPEDANCE OHMS Channel Mode p O WER *12V REMOTE GROUND SPEAKER CONN FUSE GRIOGED MODE e Plunet kucJi0 Chassis ground point to REMOTE TURN-ON terminal of head unit...
- Page 13 Speaker Wiring 2-ChanneI Amplifiers Tri-Mode AC600.2 Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO.
- Page 14 Power and Speaker Wiring 4-ChanneI Amplifiers 4 Channel and Bridged Modes AC800.4 AC1200.4 Speaker SPEAKER IMPEDANCE Speaker OHMS Four Channel Mode POWER 013 e 00*4e FUSE +12V REMOTE GROUND Audio Chassis ground SPEAKER point IMPEDANCE Speaker OHMS to REMOTE TURN-ON terminal of head unit...
- Page 15 Power and Speaker Wiring 4-ChanneI Amplifiers Tri-Mode AC800.4 AC1200.4 Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO.
- Page 16 Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM POSSIBLE REMEDY Amplifier will not Check to make sure you have a good ground connection.
- Page 17 Specifications 2-Channe1 MOSFET Amplifiers MODEL AC600.2 POWER 150W into 4 Ohms POWER 300W into 2 Ohms BRIDGED POWER 600W into 4 Ohms Min. speaker 2 Ohm Stereo impedance 4 Ohm Mono Bridged 0.01% Frequency response 20Hz-20kHz Signal-to-noise ratio 102dB 90dB...
Need help?
Do you have a question about the AC600.2 and is the answer not in the manual?
Questions and answers