NAPCO RP1054D Operating And Installation Instructions

.64
DESCRIPTION
The RP1054D is a user-friendlybacklit keypaddesigned
for Napco's IJL-llsted MA854. MA1008 and MAI 010 control
pands.A large7-segmentalphanumerEdis*y functions
as a readout for control-panel Enforrnation and zone Wen-
tiflcation. Installation is quick ard easy on
This manualprovwesInstallationinforrnationONy.Refer
to the accompanying User's Guide (01142)for keypad
functions and operation,
furnishedwm thecontrol panelfor panelmounting,wiring,
programming inforrnat/on.
SPECIFICATIONS
Operating Voltage: 9.0—13.0Vdc
pand)
Current: 40mbA*typical
Wiring Length: 1 keypad,1000'rnu.; 5 keypads, 3 00'rrøx.
using +22AWG wire)
Dimensions: x 5%" x 1%6" (Hx%O)
from available combined standby current of
control panel
MOUNTING
Opening the Keypad. There are two slots along the
bottom edge of the keypad about I inch from each side.
To open, insert a medium screwdriver into either slot and
push up with a slight twisting motion to release the retainer
tab. Repeat for the other slot. Pull out at the bottom and lift
off the two hooks at the top.
This keypad features a handy pull-up reference label.
(Thislabel must be used In IJLinstallations.) Before mount-
ing the keypad onto the wall, push the Siding Labd Plate
(with label and felt backing affixed and
ward) down the guides at the rear of the keypad untu it
snaps into place. Once installed, the Sliding I abel Plate
cannot be removed without first removing the keypad from
the wall.
When instaElingthe rear case, be sure that thewords
and "TOP"(molded into the case) are property oriented. The
rear case Is provided with a variety of holes to accom-
modatevirtuallyany mounting situation.The four angled
elongatedhdes are for mountingdirectly intoa wall using
appropriatescrews;these hdes will allowlevellingadJust.
ment Thefour comer holes may be usedwhen replacing
an RP854Keypad RPB-I Backplate for surface mount-
ing directly onto a wall. The RP1054Dreplacesboth the
keypadandthe backßate.If installing intoa double-gang
box. insert mouüg screws through the two vertical elon-
gated holes on the left sEe of the case and into the box. If
the box is visiUe Whenviewedfrom the front, adjust the
O NAPCO 1990
four wires.
to the installation manual
by control
facing for-
Untitled (2).max
Untitled (2).max
OPERATING AND INSTALLATION
RPI 054D
DESIGN PATS. PENDING
keypad vertically, then tighten the
hardware suttable for the mounting
screws at the right side ot the keypad case directly IMOthe
wan to ensure a secure
WIRING
Wire the keypad to the control pand terminals shown in
Table 1. Note: If using a sddering iron, be careful
sgiash sdder onto the keypad circuit board or com-
ponents, as darnage could resutt.
Keypad Wire Color
Ydlow
Green
Red
Black
WhÄe
Table 1. Keypad
Remote Panic. To connect a remote panic bi-mon, splice
the two white rlbbon-cable wires to a norrrel!y-open
momentary-contact pushbutton switch. Simitarty, addition-
al panic buttons
needed. If remote panic will
leads, as a short across them WIIcause a panic alarm. Note
that in UL installations,
located In the room as the key}M
Backlighting. Backlighting reVes
In normal use, the keypad is always dimly backlit. To
disaue backlighting, see JUMPER OPTIONS.
JUMPER OPTIONS
Several Jumpers provide a variety of options. They are
conveniently located around the perimeter of the board for
æsy access. To identify the location of the jumpers, refer
to the label affixed to the fishpaper on the back of the board.
Disable Keypad Panic. Cut Jumper A (bottom-center) to
disable the keypad panic buttons, Keys [t] and [#1.
Disable Keypad Sounder. Cut Jumper B (lower-right) to
completely disable the sounder. Do not d isable the sounder
in UL installations.
Disable Touchpad Backlight. Cut Jumper C (upper-
right) to disable touchpad backlighting.
COMPLETING THE INSTALLATION
To reassemble the keypad after installation. teng the top
of the front pand onto the hooks in the rearcase
INSTRUCTIONS
KEYPAD
W1512B 5m
Then, using
surface, add one or two
Installation.
MA854 MA1008 MAIOIO
1 5
2 6
3 3
4 4
to normally-open remote
panic switch(es)
to control-panel terminals.
be wired in parallel with the first, as
be used, insulate both white
rernote panic buttons must be
no additional wiring.
to
6
7
3
4
push