Advertisement
Quick Links
Advertisement
Related Manuals for Bissell 2306A
Summary of Contents for Bissell 2306A
- Page 1 CROSSWAVE ® PET PRO _______________ USER GUIDE 2305, 2306 SERIES...
- Page 2 3-prong grounded plug. » Do not put any object into open- » Use only BISSELL cleaning » Do not leave appliance when it is ings. Do not use with any opening products intended for use plugged in.
- Page 3 Thanks for buying a BISSELL CrossWave® Pet Pro We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your multi-surface cleaner works as well in two years as it does today, so this guide has tips on using (pages 6-8), maintaining (pages 9-13), and if there is a problem, troubleshooting (page 14).
- Page 4 Integrated Carry Handle Rinse Cup Dirty Water Tank Rinse and Storage Tray Your BISSELL CrossWave® Pet Pro machine comes • Handle in three easy to assemble components and does • Body not require any tools to assemble. The unit also •...
- Page 5 Cleaning Formulas WARNING To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the hard floor device. CROSSWAVE® FORMULAS Keep plenty of CrossWave® formulas on hand so you...
- Page 6 Screw the cap back onto the clean water tank. A few notes about filling the clean water tank: • Fill with warm (140°F/60°C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE. www.BISSELL.com...
- Page 7 TIP: For overly challenging and stuck-on messes on your hard floors, activate the RUG mode and hold your CrossWave® Pet Pro over the mess. Using short passes while holding the trigger allows the multi-surface brush to go to work. www.BISSELL.com...
- Page 8 NOTE: The RUG button dispenses twice the solution of the HARD FLOOR button to help with area rug cleaning. ATTENTION Do not over wet carpet. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure. www.BISSELL.com...
- Page 9 Repeat as needed. Pull brush roll out by grabbing the Place the brush roll upright in the Brush Roll brush roll tab and pulling upward. Drying Tray to dry. www.BISSELL.com...
- Page 10 Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and may void the warranty. NOTE: Any solution remaining in the clean water tank should be emptied prior to machine storage. www.BISSELL.com...
- Page 11 Hand wash the vacuum filter and screen with Rinse the float located at the bottom of the warm water and mild detergent. top of the dirty water tank. www.BISSELL.com...
- Page 12 Then tilt the top of the dirt tank toward Once parts are dry, Place strainer back into the machine and push into reassemble and replace dirty water tank. place until you hear a click. the top of dirty water tank. www.BISSELL.com...
- Page 13 Then lock of the foot. Then press the window back into the pull tab into place by pressing downward. place until you hear a click. www.BISSELL.com...
- Page 14 Cap of clean water tank is not closed Remove the clean water tank and re-apply leaking properly the cap Too much water applied Go over area without spraying down water Machine is Previous floor care products used Contact product manufacturer regarding streaking how to remove www.BISSELL.com...
- Page 15 Service If your BISSELL product should require service: Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.
- Page 16 (and millions of your closest friends) For Parts and Supplies, go to BISSELL.com and know what you think! enter your model number in the search field. For cleaning tips and more visit www.BISSELL.com or find us at: BISSELL BISSELLClean BISSELLClean BISSELL BISSELL ©2017 BISSELL Homecare, Inc...
Need help?
Do you have a question about the 2306A and is the answer not in the manual?
Questions and answers