Lutron Electronics RadioRA2 Installation Instructions

Installation Instructions
Please Read Before Installing
Use these instructions to install the model numbers listed above.
For system setup instructions and tools visit:
www.lutron.com/radiora2
Features
• Provides 2 Contact Closure Inputs (CCI) for integration with other systems and
1 CCI for security systems.
• Provides 4 Contact Closure Outputs (CCO) to control up to 4 garage doors or
motorized gates.
• Can receive commands from up to 10 transmitters.
• Includes pre-printed and blank labels for naming buttons.
Important Notes
Environment
Visor Control Receiver:
Ambient operating temperature: 32 °F to 140 °F (0 °C to 60 °C), 0% to 90%
humidity, non-condensing. Indoor use only.
Visor Control Transmitter:
Ambient operating temperature: -40 °F to 235 °F (-40 °C to 113 °C), 0% to 90%
humidity, non-condensing. Meets the Society of Automotive Engineers (SAE)
temperature standards.
Codes
Install in accordance with all local and national electrical codes.
Cleaning
To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning
solutions.
Receiver DC Adapter Power
NOTICE - Using a DC adapter not rated at the proper specifications could
damage the Receiver and possibly overheat the DC adapter. Use only the Lutron
DC adapter listed above.
Transmitter Battery Power
A Visor Control Transmitter uses two (2) CR 2032 batteries (included). Keep
batteries out of reach of children. Using improper batteries could damage
the Transmitter. DO NOT dispose of the batteries in normal household waste.
Please recycle batteries, take to a battery disposal facility, or contact your local
waste disposal provider regarding local restrictions on the disposal or recycling
of batteries.
RF Device Placement
The Visor Control Receiver must be within 30 ft (9 m) of an RF signal repeater.
The maximum operating distance between a Visor Control Receiver and a Visor
Control Transmitter is 150 ft (46 m).
Programming
For programming instructions, see the system Setup Guide provided with the
system or visit the website listed above.
Installation of a Visor Control Receiver
1. Find a suitable location for the Receiver either near a security sytem panel
or above a garage door opener and within 30 ft (9 m) of a repeater. For more
information regarding the proper placement of a Receiver in a system see the
system Setup Guide located at the website listed above.
2. Mount vertically or horizontally, as shown in the Mounting Diagram, using two
#6 (M3) screws (included). When mounting, allow 7 in (177.8 mm) clearance for
the antenna and ensure convenient access to the contact closures and front
buttons. In order to achieve proper RF performance, do not mount unit in a
metal enclosure.
3. Attach the DC adapter cord to the power jack on the Receiver and insert the DC
adapter plug into a 120 V
Installation of a Visor Control Transmitter
1. Attach the visor clip to the Visor Control Transmitter as shown in the Mounting
Diagram.
2. Mount the Transmitter onto a vehicle's visor.
* Typical Power Consumption test conditions: two LEDs on (two presets active), Receiver powered by the
9 V adapter supplied, no Contact Closure Outputs or Contact Closure Inputs active.
Technical Assistance:
U.S.A. / Canada: 1.800.523.9466
Mexico: +1.888.235.2910
Other Countries: +1.610.282.3800
24 hours a day, 7 days a week.
60 Hz receptacle.
English
Visor Control Receiver: RR-VCRX
9 V 300 mA
DC Adapter: T120-9DC-3-BL
Input: 120 V 60 Hz 6.5 W
Output: 9 V 300 mA
Typical Power Consumption*: 1.6 W
Visor Control Transmitter: LR-3B-H
3 V 10 mA
®