CARVIN CM50 Specifications

CARVIN ENGINEERING DATA
GENERAL
The CM50 is Carvin's entry level vocal mic.
It is designed mainly for vocals, however, it
can easily double for micing guitar amps or
drums (excluding kick drum). Features a con-
venient on/off switch for reducing noise and
feedback when not in use. Unidirectional
with a cardioid polar pattern. Built in foam
wind screen for pop, breath, and wind noise
rejection.
Microphone Features:
Bright, clean sound. Especially good for
announcing, narration and dialogue, vocal
music, and rhythm pickups
Wind and "pop" filter readily removable
for cleaning or replacement
Unusually effective cardioid pickup pattern to
minimize background noise and undesirable
effects of studio and location acoustics. Rear
and side rejection uniform to very low fre-
quencies and completely symmetrical about
microphone axis
Self-contained spherical filter to control
explosive breath sounds ("pop") and wind
noise in outdoor locations
Cartridge shock-mounted for protection and
quiet operation
On/Off switch
TYPICAL FREQUENCY RESPONSE
–60
–70
–80
–90
–100
–110
20 200 Hz
FIGURE 1
INTERNAL CONNECTIONS
POSITIVE
CARTRIDGE
NEGATIVE
GUARANTEE
This Carvin product is guaranteed in nor-
mal use to be free from electrical and
mechanical defects for a period of one year
from date of purchase. Please retain proof
of purchase date. This guarantee includes
parts and labor.
CARVIN 12340 WORLD TRADE DRIVE, SAN DIEGO, CA 92128 PH 619-487-1600
SPECIFICATIONS
Type
Dynamic
Frequency Response
50 to 15,000HZ
Output Level (at 1,000 Hz, 600 ohms)
Open Circuit Voltage*
-72 dB, (0.19 mV)
Cable
CM50: 6.0m (20 ft) three-conductor shield-
ed broadcast type with 3-socket profession-
al audio connector*
Case
Dark grey powder coat die casting and
dark grey powder coat steel mesh grille
Swivel Adapter
Slip-in positive-action, adjustable from 0° to
90°, with standard 5/8"-27 thread
Net Weight (less cable)
8.5 oz.
* To mate with Cannon XL series, Switchcraft A3
(Q.G.) series or equivalent connector
Polar Pattern
Cardioid — rotationally symmetrical about
microphone axis, uniform with frequency
(see Figure 2)
150°
120°
90°
2k 20k
60°
30°
TYPICAL POLAR PATTERNS
MICROPHONE
3
ON – OFF
1
This guarantee is in lieu of any and all other
guarantees or warranties, express or implied,
and there shall be no recovery for any conse-
quential or incidental damages.
180°
150°
120°
90°
-25
-20
-15
60°
-10
200Hz
1,000 Hz
-5
6,000Hz
30°
0dB
0°
FIGURE 2
3
1
2 2
MODEL CM50
UNIDIRECTIONAL DYNAMIC MICROPHONE
MODEL CM50
UNIDIRECTIONAL DYNAMIC MICROPHONE
ARCHITECT'S SPECIFICATIONS
The microphone shall be a moving coil
(dynamic) type with a frequency response of
50 to 15,000 Hz. The unit shall have a car-
dioid polar characteristic. The cancellation at
the sides shall be approximately 5 dB, and
the cancellation at the rear shall be 15 to 20
dB. The microphone shall have a rating
impedance of 600 ohms.
The microphone connector shall be a 3-pin
professional audio type designed to mate with
Cannon XL series, Switchcraft A3 (Q.G.) series
or equivalent connector. The microphone shall
be provided with a swivel adapter adjustable
through 90° from vertical to horizontal. The
adapter will mount on a stand having a 5/8" -
27 thread. The overall dimensions of the
microphone shall be 130 mm in length and 53
mm in diameter.
The microphone shall be the Carvin CM50 or
equivalent.
1 GND
2 POSITIVE
3 NEGATIVE
CABLE
SHIPPING INSTRUCTIONS
Carefully repack the unit, have it insured, and
return it prepaid to:
Carvin Corp.
Attention: Service Department
12340 World Trade Drive
San Diego, CA 92128