Related Manuals for TP-Link VIGI SP9030
Summary of Contents for TP-Link VIGI SP9030
- Page 1 Installation Guide VIGI Intelligent Solar Power Supply System/ VIGI Solar System Controller © 2025 TP-Link 7106512069 REV1.20.0...
-
Page 2: Table Of Contents
Contents Chapter 1 Overview ———————————— 1 Chapter 2 Installation ——————————— 5 Package Contents ..........5 Safety Precautions ..........6 Installation ...............6 Chapter 3 Configuration —————————— 13 Appendix FAQ ——————————————— 15... -
Page 3: Chapter 1 Overview
Chapter 1 Overview The TP-Link VIGI intelligent solar power supply system consists of three parts: horizontal mount (containing the controller and modular battery), solar panel, and vertical mount. The VIGI solar system controller consists of a horizontal mount (containing the controller and modular battery) and vertical mount. - Page 4 Off: PV panels have no voltage. On: Battery power is higher than 20%. Flashing Slowly: Battery power is lower than 20%. Flashing Quickly: Intelligent auxiliary heating. Off: Battery is abnormal. • Specifications Items VIGI SP6020 VIGI SP6030 VIGI SP9030 Battery Type Lithium Battery Capacity 20.8AH 31.2AH...
- Page 5 The solar panel is shown in the following figure. Solar panel Junction box Four-pin male connector for connecting the solar system controller • Specifications Items VIGI SP6020/VIGI SP6030 VIGI SP9030 Size 690mm×516mm×30mm 998mm×516mm×30mm Output Power/ 60W/18V 90W/18V Voltage...
- Page 6 Vertical Mount ■ The mount is shown in the following figure. Vertical Mount PTZ Camera Connector...
-
Page 7: Chapter 2 Installation
Chapter 2 Installation Package Contents Make sure that the package contains the following items. Please contact your distributor, if any of the listed items are damaged or missing. The figures are for demonstration only. The actual items may differ in appearance and quantity from what is depicted. -
Page 8: Safety Precautions
Safety Precautions • During installation, collision and knocking are strictly prohibited to avoid damage. • When placing the solar panel, make sure that the solar panel is facing upwards and placed horizontally. Uneven ground may scratch or damage the solar panel. •... - Page 9 U-shaped screws Tip: Determine the direction according to a compass or mobile phone compass software, and adjust the orientation of the bracket to obtain the maximum solar energy. Step 4. Install the vertical mount 1. Remove the side panel of the vertical mount. 2.
- Page 10 M6*20 Step 5. Install the solar panel Note: For the SP9030/SP6030/SP6020 VIGI Intelligent Solar Power Supply System, skip step 1. 1. Install the solar panel bracket to the solar panel. M8*20...
- Page 11 2. Install the angle adjustment bracket to the solar panel bracket. M8*20 3. Determine the installation inclination according to the location (the inclination can be determined according to the location's latitude). Recommended Solar Panel Inclination Angles (The inclination angles correspond to the holes on the mount): Latitude Range Recommended Inclination 0-5°...
- Page 12 5. Thread the solar panel's four-pin male connector through the side hole of the vertical mount, and connect it to the four-pin female connector of the controller. Step 6. Install the load device 1. Install cameras on the vertical mount using camera mounting screws (M4*20).
- Page 13 1 Install the PTZ camera connector using M6*20 mounting screws. 2 Install the PTZ camera using M6*20 mounting screws. Note: 1. Third-party PTZ cameras are compatible. 2. If the product is used in a windy area, it is recommended to securely attach VIGI 5-Series cameras directly to the pole to minimize the impact of strong winds on image quality.
- Page 14 2. Connect the cameras to the solar system controller's load intefaces. When connecting the cameras, use the provided waterproof rubber pipe sleeves for waterproofing. Note: For secure waterproofing, you can wrap the connection with over two layers of waterproof tape (not included), as shown below. Wrap the first layer, then cut. Apply a second layer, ensuring no gaps between the connection and tape.
-
Page 15: Chapter 3 Configuration
Interface Step 2. Follow the instructions to finish the quick setup. 1. Download and install the latest TP-Link VIGI app. 2. Open the app and log in with your TP-Link ID. If you don’t have an account, sign up first. - Page 16 3. Tap the + button on the top right and follow the app instructions to add the VIGI solar system controller. Step 3. Done. The VIGI solar system controller is added to your network and can provide power to your devices. You can control and manage the VIGI solar system controller via the VIGI app remotely.
- Page 17 Appendix FAQ Q1. What should I do if the controller's LED status is abnormal? • SYS LED is off: This could indicate a power issue or a damaged system board. • LAN LED is off: There is no connection. Check whether the RJ45 interface is firmly connected to the network device.
-
Page 18: Safety Information
EU Declaration of Conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/...
Need help?
Do you have a question about the VIGI SP9030 and is the answer not in the manual?
Questions and answers