Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Harrison D510mx
Summary of Contents for Harrison D510mx
- Page 1 D510r - D510dante - D510mx User Guide www.harrisonaudio.com...
- Page 2 As research and development is a continual process, Harrison Audio LLC reserves the right to change the features and specifications described herein without notice or obligation. Harrison Audio LLC cannot be held responsible for any loss or damage arising directly or indirectly from any error or omission in this manual.
-
Page 3: Table Of Contents
Rear Connectors Input / Output XLR Connectors XLR Pinout Overview D510dante Introduction Features Installation 10-11 Tutorial Specifications Block Diagram Overview D510mx Introduction Features Installation 16-18 Tutorial 18-19 Configuration Options Specifications 20-22 Block Diagram Safety Notices 24-27 D510r - D510dante - D510mx... -
Page 4: Overview D510R Introduction
D510r Introduction The D510r is a 19” 3 RU rack unit designed to house up to 10 standard 500 series modules. The D510r is designed to house the most power-hungry modules and ensure the full performance of those modules. The D510r includes a built-in power supply with sufficient current to handle any complement of 500 series modules. -
Page 5: Hardware Overview
Introduction Safety Notices Please read the safety notice information included on the Safety Sheet inside the box before using the D510r. This information is also available in Appendices section of this User Guide. Hardware Overview This section provides an overview of the D510r hardware. The tutorial section covers each control in more detail. -
Page 6: Tutorial
Tutorial Power On Power on the unit by toggling the power switch (far right end of the D510r) to the up (I) position. Pqwer off the unit by toggling the power switch down to the (O) position. Front Slot Controls <... -
Page 7: Status Panel Pwr And Mute Leds
Tutorial Status Panel LEDs PWR LED The PWR LED illuminates when the D510r is powered on. MUTE LED The MUTE LED illuminates when the optional D510dante interface is not connected to a network. Rear Connectors Input / Output XLR Connectors Each 500 slot has a corresponding female XLR input and male XLR output connector associated with the slot. -
Page 8: Xlr Pinout
Tutorial XLR Pinout Diagram Specifications Dimensions: L = Standard (19”) x H = 3RU (5.25”) x D = (7.2”) Power Input: 50/60Hz / 80-246VAC / 1.8 -0.55A Power Per Slot: 170ma Weight: 10.4 LBS (4.72kg) D510r - D510dante - D510mx... -
Page 9: Overview D510Dante Introduction
D510dante Introduction One of the advanced and unique features of the Harrison D510r 500 rack unit is ability to add a D510dante interface card which includes A/D and D/A converters via a Dante interface providing a direct Ethernet interface to a DAW or other Dante network such as for live performance applications. -
Page 10: Installation
Appendices section of this User Guide. Introduction This document provides instructions for installing the D510dante Interface. The D510dante is an upgrade for the D510r that attaches to the back panel and enables Dante connectivity. D510r - D510dante - D510mx... - Page 11 Remove the blank plate from the back of the D510r by removing the 8 screws. Step 2 Install the D510dante into the back of the D510r. Make sure to line up all pins and guideposts. Step 3 Install the 8 included screws.
-
Page 12: Tutorial
Dante Controller software permits renaming of the Dante signals on the Dante Controller router page. This is left to the user if the standard signal naming needs to be changed to suit a particular studio installation. D510r - D510dante - D510mx... -
Page 13: Specifications
Frequency Response: 20 Hz – 20 KHz +/- 0.25 dB Connectors 2 x RJ45 Network Ports (Primary and Secondary) BNC TTL Wordclock Latency DA + AD <> Dante - 48kHz and 96kHz = 43.2 samples (0.9ms@48kHz, 0.45ms@96kHz) D510r - D510dante - D510mx... -
Page 14: Block Diagram
Tutorial D510dante Block Diagram D510r - D510dante - D510mx... -
Page 15: Overview D510Mx Introduction
The outputs from each 500 module slot feed the first 8 inputs to the D510mx. Inputs 9 and 10 to the D510mx are fed from the 9th and 10th slot input XLR connectors on the rear of the D510r rack. Each input to the D510mx has a level, pan and stereo bus routing switch. -
Page 16: Installation
Introduction This document provides instructions for installing the D510mx Rack Mixer. The D510mx is an upgrade for the D510r that attaches to the front of the unit and provides a mixing interface with two headphone outputs. Note that the D510mx requires slots 9 and 10 of the D510r to be empty. - Page 17 9 and 10 of the D510r to be empty. Please see the user manual for operating instructions. First, make sure the D510r is turned off. Then, remove the Status Panel from the D510r by removing all four screws from the front and disconnecting the 20-pin ribbon cable from the back.
-
Page 18: Tutorial
Step 3 – Mount D510mx Mixer Panel Secure the D510mx onto the right side of the D510r using the 8 included screws. Tutorial Mixer Front Panel Controls 1 – Mix Bus Routing Each of the 10 D510mx sources can rout independently to the D510mx mix bus via the red switch. The associated LED lights when the signal is routed to the mix bus. - Page 19 Separate Headphone TRS jacks are provided one for each headphone output. 9 – Power LED The red PWR LED comes on when the D510r has power. Note: The rest of the controls on the lower right section of the D510mx are reserved for future use.
-
Page 20: Configuration Options
D510r + D510mx D510r + D510mx + D510dante Specifications General The Harrison D510mx Mixer Module is an upgrade for the D510r that attaches to the front of the unit and provides a mixing interface with two headphone outputs. D510mx Inputs •... - Page 21 Minimum Gain: <= -78 dB Noise A-Weighted @ Min Gain: < -87 dBu ▪ • Maximum Gain: 0 dB ▪ THD+N, 1kHz 20 dBu @ Max Gain: < 0.004% ▪ Noise A-Weighted @ Maximum Gain: < -82 dBu D510r - D510dante - D510mx...
- Page 22 Signal Metering • 3x tri-colour LED signal presence ▪ Green: >= -14 dBu, < 4 dBu ▪ Orange: >= 4 dBu, < 18 dBu ▪ Red: >= 18 dBu Connectors • TRS Stereo Headphone Output (2) D510r - D510dante - D510mx...
-
Page 23: Block Diagram
Block Diagram D510r - D510dante - D510mx... -
Page 24: Safety Notices
• Harrison does not accept liability for damage caused by maintenance, repair or modification by unauthorized personnel. • When using this apparatus either fix it into a standard 19” rack or place it on a secure level surface. - Page 25 • The appliance coupler is used as the disconnect device, ensure that it is connected to an unobstructed wall outlet. • Connect only to an AC power source that contains a protective earthing (PE) conductor. • Only connect units to single phase supplies with the neutral conductor at earth potential D510r - D510dante - D510mx...
-
Page 26: Fcc Certification
Electrical Safety IEC 62368-1:2018 BS EN IEC 62368-1:2020+A11:2020 CSA CAN/CSA-C22.2 No. 62368-1 3rd Ed. UL 62368-1 3rd Ed. D510r - D510dante - D510mx... -
Page 27: Further Information
The unit’s construction method will allow easy dis-assembly supporting separating and recycling core components when the product reaches its end of life. D510r - D510dante - D510mx...
Need help?
Do you have a question about the D510mx and is the answer not in the manual?
Questions and answers