Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module The module installer must inform the end 1.0 Introduction customer (or consumer) of the above matters accordingly. This manual contains relevant information about the installation methods and safe operation of 1.1 Declaration photovoltaic modules (hereinafter referred to as "modules") of Jolywood Solar Technology Co., Ltd...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module operation instruction 2.3.1 General Safety In order to avoid damage module, please do not 2.2.1 scratch or hit module, and do not use paint or It is strictly forbidden to use modules with broken glass.
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module with recommended shipping method unpacking procedure. In order to avoid damage, scratch or strike module. Do not apply pressure directly on the module during transportation. Improper transportation or installation also may damage module, which is excluded from the warranty.
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module attached to the vehicle with ropes. Pallets are Unloading Instructions prohibited beyond the loading area of transport 3.2.1 When unloading modules from vehicle, less than vehicles. 2 lots package could be lifted each time with a reasonable fixture.
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module the soft and collapsible ground. Instead, the hard 4.1.3 ground or the ground with high terrain should be Wear protective gloves during unpacking to avoid selected and leveled to ensure that the modules injury and fingerprints on the glass surface...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module the other side of package, and then carry them. If 5.1.2 unpacking on a non-horizontal floor, use a remove module package before supportive tool to ensure package placed installation. verticality. 5.1.3 When installing modules, only work in a dry 4.2.4...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module 5.1.8 5.2.2 Framed Bifacial Double-Glass After modules are installed, the cables should be Modules (installation with clamps) fixed or tied to avoid exposed under direct Clamp: sunlight after installation, which would prevent cable from aging.
Page 10
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module Press block installation mode and corresponding static load: Four point long side installation of mounting rail Four point long side installation of mounting rail perpendicular to the long side parallel to the long side...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module Four point short edge Installation Four point long side Four point long edge Four point short side Four point short side installation+two point installation of nstallation of installation of Four point...
Page 12
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module Bolt installation method and corresponding static load: Long frame with inner four holes Long frame with inner four holes mounting rail parallel to the long side mounting rail perpendicular to the long side (HD108N(M10)&HD108N-R0 &...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module Long frame with Long frame with Long frame with Long frame with Long frame with Long frame with Long frame with Long frame with Instllation inner four holes 400mm&1400mm inner four holes...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module Installation The flat single shaft is The flat single shaft is The flat single shaft is The flat single shaft is installed with 400mm installed with 1100mm mounted with 1300mm installed with 1400mm...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module 5.2.6 Electrical Installation Under certain conditions, a module may produce All wiring should be performed by a qualified and more current or voltage than its Standard Test trained person accordance with local Conditions rated power.
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module Alternatively, a more accurate correction factor for series or in parallel needs to be reasonably the open-circuit voltage can be calculated using designed according to the system configuration. the following formula: All instructions above must be followed to meet α...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module 6.1.5 6.Maintenance for PV Modules Cover the front surface of Modules with an opaque material. Modules exposed under the sun could 6.1.Module Visual Inspection and be extremely dangerous, as high voltages could...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module f)If you are not sure whether the array need to 6.3.Cleaning cleaned, first select a column of particularly dirty The amount of electricity produced by a solar array to begin cleaning. If the power generated...
Installation Manual - Jolywood N-type Mono-crystalline Double Glass Module 7. Technical Issues or Claims 6.3.2 Module inspection after cleaning 6.3.2.1 If you have any questions about technology or The overall appearance of modules is clean, claims, please contact the installer.
Need help?
Do you have a question about the HD156N and is the answer not in the manual?
Questions and answers