Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Motorline SIGMA X6
Summary of Contents for Motorline SIGMA X6
- Page 1 SIGMA X SIGMA X USER / INSTALLER'S MANUAL v1.3 REV. 08/2024...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS INDEX This product is certified in accordance with European Community 01. SAFETY INSTRUCTIONS (EC) safety standards. 02. AUTOMATISM This product complies with Directive 2011/65/EU of the European TECHNICAL CHARACTERISTICS Parliament and of the Council, of 8 June 2011, on the restriction DIMENSIONS of the use of certain hazardous substances in electrical and COMPONENTS... -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. • If the power cable is damaged, it must be replaced by the Read all instructions carefully before beginning the installation/ manufacturer, after-sales service or similarly qualified personnel usage procedures and keep this manual in a safe place that it can... - Page 4 • Pay special attention to the danger of falling objects or uncontrolled movement of doors/gates during the installation or operation of MOTORLINE ELECTROCELOS SA. this product. Travessa do Sobreiro, nº29 4755-474 Rio Côvo (Santa Eugénia)
-
Page 5: Automatism
02. AUTOMATISM 02. AUTOMATISM TECHNICAL CHARACTERISTICS DIMENSIONS Standard measures SIGMA X SIGMA X is an electromechanical barrier designed to control vehicle access to private, industrial or commercial areas. Automatism technical specifications: • Power 150W ⎓ • Barrier power 110/230Vac 50/60Hz •... - Page 6 02. AUTOMATISM 02. AUTOMATISM DIMENSIONS DIMENSIONS Standard measures SIGMA XS5 Standard measures SIGMA XA5 3000 5000 2200 5000...
-
Page 7: Components 6B
02. AUTOMATISM 02. AUTOMATISM DIMENSIONS COMPONENTS Standard measures Standard measures FIXED SPAT FIXED SPAT BASE COMPONENTS • Control board • Built-in inside flashing light • User Manual • MF30 Photocells • 2 FALK remote controls • Boom mounting accessories • Barrier fixing plate •... -
Page 8: Flashing Light 7A
02. AUTOMATISM 02. AUTOMATISM FLASHING LIGHT MANUAL OPENING / CLOSING This barrier has two RGB flashing light integrated in the top cover, for emission of red, green and blue Under no circumstances should you put your hands on the movement axis of the motor and colors. -
Page 9: Installation
03. INSTALLATION INSTALLATION MAP 1 • Barrier 9 • Barrier cover 2 • Boom 10 • Transformer / LED Module 3 • Boom extension 11 • Manual movement crank 4 • Photocell support column (not included) 12 • Motor 5 • Photocell 13 •... -
Page 10: Remove Cover And Profiles 9A
03. INSTALLATION 03. INSTALLATION REMOVE COVER AND PROFILES FOUNDATION CREATE FOUNDATION This barrier allows free access to the interior to facilitate the product installation and maintenance • process. To do so, remove the aluminum cover and profiles from the barrier. Drill a hole of 355x470mm and 400mm (or greater) deep to create the fixing foundation. -
Page 11: Installation
03. INSTALLATION AUTOMATISM INSTALLATION Mount the bolts and screws to the mounting Route the electrical cables to connect the control board to accessories and power. Leave cables with a length that guarantees easy connection to the control board at the top of the barrier. plate as exemplified in step Position the barrier on the plate leaving it centered and secure it by tapping the screws inside the With the cement still fresh, apply the fixing plate... -
Page 12: Boom Direction 11A
(DX). If it is for a 4 meter boom (SIGMA X4) follow the instructions on page 12 to change to 1 spring. If the boom is not in the desired position, follow the instructions on page 12 to reverse the... -
Page 13: Spring Installation
03. INSTALLATION SPRING INSTALLATION CHANGE FROM 2 TO 1 SPRING • If the springs are on the wrong side for the intended *If, due to the size of your boom, there is a need to remove boom direction (see diagram on page 11A), you must a spring, proceed as follows: reverse the position of the springs on the rotation lever. -
Page 14: Boom Mounting - Sigma X
03. INSTALLATION BOOM MOUNTING - SIGMA X Fit the remaining pieces in the order shown in the picture. Route the cable that comes out of the barrier shaft through the hole CHECK POSITION OF THE BOOM SUPPORT • in the assembly you assembled. Secure the parts to the boom fixing plate with screws and nuts provided in the package. -
Page 15: Boom Mounting - Sigma Xs5
03. INSTALLATION 03. INSTALLATION BOOM MOUNTING - SIGMA XS5 BOOM MOUNTING - SIGMA XA5 Apply the same steps from page 13 (1, 2, 3, 4) to Apply the same steps from page 13 (1, 2, 3, 4) to the SIGMA XS5 boom and add step 5 to complete the SIGMA XA5 boom and add step 5 to complete assembly. -
Page 16: Fix Boom Supports
03. INSTALLATION FIX BOOM SUPPORTS • SET EXTENDABLE BOOM LENGTH • ADJUSTING SUPPORT (FIXED) HEIGHT You should now set its length so that you can then place the support as shown in the image below. If the height of the support arm is misaligned to the height of the boom you will have to adjust the arm The boom should exceed the position of the support (SPAT FIXED) arm by 50mm. -
Page 17: Adjustment Of The Booms
03. INSTALLATION ADJUSTMENT OF THE BOOMS • ADJUST XA5 MOBILE SPAT • ADJUST XS5 BOOM • ADJUST XA5 BOOM If the floor is uneven or you want to adjust the edge Turn the crank (highlighted below) if you want to Turn the crank (highlighted below) if you want to height, you will need to adjust the floor stopper. -
Page 18: Adjust The Springs
03. INSTALLATION ADJUST THE SPRINGS Before adjusting the springs, manually place the boom in a vertical position so that the springs are in Hold the threaded rod with pliers so that it does the lowest tension position (see page 7B). not rotate, and then tighten the adjusting nut until each spring is stretched the distance mentioned in the table on page 18. -
Page 19: Adjusting Tables - Sigma X
19A. Hole 2 Hole 1 • Depending on the condition of the spring, there may be a tolerance SIMPLE BOOM SIGMA X4 SIGMA X6 of 5mm in relation to the values indicated in the table. Boom Length 3000... -
Page 20: Testing Spring Adjustment 19A
03. INSTALLATION 03. INSTALLATION TESTING SPRING ADJUSTMENT POWER CABLE * The barrier structure has a tube located on the inside so that it can lead the supply wiring to the connectors The motor must remain unlocked to perform the tuning test. (top of the barrier). -
Page 21: Adjust The Stoppers 20A
03. INSTALLATION 03. INSTALLATION ADJUST THE STOPPERS ADJUST THE LIMIT SWITCHES The stoppers in the barrier are visible in the image below. The SIGMA X has limit switches to complete the opening and closing maneuvers, located on the • They consist of 2 adjusting screws (one on each side of the barrier) fastened to the base as well as its rotation lever. -
Page 22: Apply Profiles And Cover
03. INSTALLATION APPLY PROFILES AND COVER APPLY PROFILES • Position the BACK PROFILE in the correct location (profile previously placed for boom application). Holding the BACK PROFILE so that it does not dislocate, fit the SIDE PROFILES into the barrier frame. -
Page 23: Connections
04. CONNECTIONS MOTOR AND FLASHING LIGHT CONNECTIONS • Control board MC60 (Barrier Interior) • MP106 module LGHI • MP106 module inside 12V+ GI RGI • LED Strip LAMP MOT1 BATT (Flashing Light) ⎓ • 12VDC Power Supply • SIGMA X 36 W Barrier •... -
Page 24: Photocell Connections And Safety Edge
04. CONNECTIONS PHOTOCELL CONNECTIONS AND SAFETY EDGE WITHOUT SAFETY EDGE WITH SAFETY EDGE (SERIAL CONNECTION) • • • LED strip (boom) • Safety Edge (Optional) • Control board MC60 LAMP MOT1 BATT (Barrier Interior) • Control board MC60 (Barrier Interior) COM NC/ COM NC/ •... -
Page 25: Troubleshooting
05. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS / SPECIALIZED TECHNICIANS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem 1 • Remove the barrier top cover; • Barrier • Make sure you have • Still not working • Consult a qualified 2 •...
Need help?
Do you have a question about the SIGMA X6 and is the answer not in the manual?
Questions and answers