Advertisement
Speedaire Operating Instructions and Parts Manual
Speedaire Portable Air Compressor
General Safety Information
E
(Continued)
N
G
4. Never use a motor with a higher
L
horsepower rating than the one
I
supplied.
S
5. Never drill into, weld or modify air
H
tank.
Changing air tank
will cause it to
weaken. Tank may rupture or
explode.
6. Do not repair a leaking tank, it
must be replaced. Never replace air
tank with a different model or
larger tank.
7. Never point any nozzle or sprayer
toward a person or any part of the
body.
8. Always wear safety goggles or
glasses when using air compressor.
9. Check maximum pressure rating
for air tools and accessories.
Regulator outlet pressure must
never exceed maximum pressure
rating.
Damage may occur
to air tools and
accessories if too much air pressure
is applied.
Always unplug air
compressor prior
to maintenance or repair. Never use
air compressor outdoors when it is
raining.
Never directly
inhale the
compressed air produced by this
unit. Compressed air contains toxic
or irritating vapors which are
harmful if inhaled.
®
10. Read labels and safety data for all
materials you spray. Follow all
safety precautions.
11. Use a mask or respirator if there is
a chance of inhaling toxic sprayed
materials. Masks and respirators
have limits and will only provide
protection against some kinds and
limited amounts of toxic material.
Read mask and respirator
instructions carefully. Consult a
safety expert or industrial hygienist
if you are not sure about the use of
a certain mask or respirator.
12. If the material you intend to spray
contains trichloroethane and
methylene chloride (read the label
or the data sheet), do not use
accessories that contain aluminum
or galvanized parts. You must
either change the material you
intend to spray, or use only
stainless steel spray equipment.
chloride can also react with
galvanized components causing
corrosion and weakening of
equipment parts.
Installation
LOCATION OF AIR COMPRESSOR
Locate air compressor in a clean, dry,
well ventilated area. Air filter must be
kept clear of obstructions, which could
reduce air delivery of the air compres-
sor. The air compressor should be
located at least 12" away from the
wall or other obstructions that will
interfere with air flow. Air compressor
head and shroud are designed to allow
proper cooling. If humidity is high, air
filter can be installed to remove
excessive moisture. Follow air filter
instructions for proper installation.
EXTENSION CORD
To avoid voltage drop and power loss
to the motor use extra air hose instead
of an extension cord. If an extension
cord must be used, be sure it is:
1. A 3-wire extension cord that has a
3-blade grounding plug, and a 3-
slot receptacle that will accept the
plug on the product.
2. In good condition.
3. No longer than 50 feet.
4. 12 gauge (AWG) or larger. Wire
size increases as guage number
decreases. 10 AWG and 8 AWG
may also be used. (DO NOT USE A
14 OR 16 AWG.)
amp circuit if:
1. Voltage supply to circuit is
normal.
2. Circuit is not used to supply any
other electrical needs (lights,
appliances, etc.)
3. Extension cords comply with
Trichloroethane
specifications in owners
and methylene
manual.
4. Circuit is equipped with 15 amp
circuit breaker or 15 amp time
delay fuse. Use a Type "T" time
delay fuse.
If any of the above conditions cannot
be met, or if operation of the compres-
sor repeatedly causes interruption of
the power, it may be necessary to
operate it from a 20 amp circuit. It is
not necessary to change the cord set.
GROUNDING INSTRUCTIONS
result in electrical shock. In the
event of a short circuit, grounding
reduces risk of shock by providing
an escape wire for the electric
current. Air compressor must be
properly grounded.
2
5Z598C
Compressor can be
operated on a 15
Improper
grounding can
Advertisement
