Advertisement
Quick Links
YOU NEED
TOKnOWTO
lnSTdLL YOUR
OVER-THE-RANGE
MICROWAVE OVEN
BEFORE YOU BEGIN INSTALLING YOUR MODEL XOOTR30BS
Read these instructions completely and carefully.
.
IMPORTANT - Save these instructions
for the local inspector's use.
IMPORTANT - Observe all governing
• codes and ordinances.
.
Note To Installer - Be sure to leave these
instructions with the consumer.
QUESTIONS - CALL XO AT 973-403-8900
WWW.XOAPPLIANCE.COM
XO
• Note To Consumer - Keep these
instructions for the future reference.
• Skill Level - Installation of this appliance
requires basic mechanical and electrical skills.
• Proper Installation is the responsibility of the
installer.
• Product failure due to improper installation is
not covered by the warranty .
I worked really hard
on this manual
so please read it ...
March 2022
Advertisement
Related Manuals for Xo XOOTR30LPS
Summary of Contents for Xo XOOTR30LPS
- Page 1 ... OVER-THE-RANGE MICROWAVE OVEN BEFORE YOU BEGIN INSTALLING YOUR MODEL XOOTR30BS Read these instructions completely and carefully. • Note To Consumer - Keep these instructions for the future reference. IMPORTANT - Save these instructions •...
- Page 2 Outside Top Exhaust........19-22 ..19 ..20 .20 - 21 ..21 .21 - 22 ..22 ..22 Recirculation..........10-12 .....10 ....11 ......11 ...11-12 ........12...
-
Page 5: Tools You Will Need
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil Carpenter square # 1 Phillips screwdriver (optional) Scissors Tin snips (for cutting (to cut template) damper, if required) Filler blocks or scrap wood pieces, if needed Electric drill with drill bits for top cabinet spacing ⁄... - Page 6 Screws Mounting Plate Screws Small Hardware Bag Exhaust Adapter Filters and Turntable Ring below glass tray Glass Tray...
- Page 9 If you plan to recirculate the exhaust back into the kitchen - proceed to page 10. If you are planning to vent the exhaust outside, turn to page 13.
- Page 10 NOTE: IT IS VERY IMPORTANT THE DIRECTIONS READ AND FOLLOW INSTRUCTIONS 3/8" TO EDGE IN THE INSTALLATION Trim the rear wall template along the dotted li ne. BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. serves to position the bottom 12" This Rear Wall Template the horizontal exhaust mounting plate and to locate...
- Page 11 is spaced out from the wall due to a cabinet depth (including cabinet doors) greater than 13.8”.
- Page 12 MOUNT THE MICROWAVE Remove the two vent plate screws A 5.2 microwave using a #1 phillips OVEN (cont.) screwdriver. 5 Insert 2 self-aligning screws through outer top cabinet holes. Turn two ful l turns on each screw. Change the charcoal filter from the vent A 5.3 plate.
- Page 15 NOT E : IT IS V E RY I MP OR TA NT T O T HE DIR E CT IONS RE AD AN D F O LLOW 3/8" TO E DGE INS T R UC T IONS IN T HE INS T ALLAT ION alon g the dotted line.
- Page 16 Carefully pull out the air director. Before: Openings face forward Air Director Rotate the air director counterclockwise 180 º BEFORE AFTER Remove the knockout plates in the back of the unit (some models require snips to perform this task) KNOCKOUT PLATES: Snip all 4 webs on each knockout panel and remove the metal knockouts for rear...
- Page 17 Replace the air director back into the opening. AIR DIRECTOR with openings facing the back Secure the blower plate to the microwave using the screw removed earlier BLOWER PLATE COVER PLATE BACK OF MICROWAVE Attach the exhaust adaptor to the rear of the unit by sliding it into the guides at the top / center of the back of the oven.
- Page 19 NOT E : IT IS V E RY I MP OR TA NT T O T HE DIR E CT IONS RE AD AN D F O LLOW 3/8" TO E DGE IN T HE INS T ALLAT ION INS T R UC T IONS alon g the dotted line.
- Page 20 Carefully pull out the air director Openings Facing Front Air Director Rotate the air director counterclockwise 180 BEFORE AFTER Place the air director back in the opening Openings Facing Rear Remove the screw that holds the blower plate to the microwave. Remove the cover plate. Replace the blower plate with the screw removed Cover Plate in Step 1.
- Page 21 (cont.) Attach the exhaust adaptor to the top of the blower plate by sliding it into the guides of the blower plate from the side. Making certain the damper operates freely, push the adaptor in until it is securely in the lcking tabs. Check once more to ensure that the damper can operate freely.
- Page 24 PN:16170000A53735 10-23/64 10-23/64 NOT E: IT READ AND IN THE FOLLO W VER Y IMPORTA THE DIRECTIONS NT TO BEFO RE REAR WAL This R ear I NST ALLATION PROC EED L TEMPLA Wal l Temp ING WI TH INSTRU T HIS CTI ONS 3/8"...
Need help?
Do you have a question about the XOOTR30LPS and is the answer not in the manual?
Questions and answers