Denon DN S5000 - DJ Table Top Single CD Player Operating Instructions Manual page 22

ENGLISH
Sampler
DN-S5000 has two Samplers of 15 seconds length. These Samplers are also used in looping playback.
Record in Sampler
q When the SAMP button
(SAMP1 (A3) or SAMP2 (A4))
is pushed in the standby or
playing, the sound from A3
or A4 point is recorded to
1
Sampler memory up to 15
seconds.
• The SAMP1 or SAMP2 button is flashing
while recording. When the recording is
completed, the button turns off and the
corresponding SAMP B LED lights up.
Setting B point
w When the B button is
pushed during Sampler
recording, the Sampler Loop
B point is set and the loop
mode turns on.
2
• Recording continues for approximately
15 seconds without stopping after set B
point.
• If the B point is not set, recording end
point set as B point automatically. Also
EXIT/RELOOP LED light to indicates
Sampler Loop mode is set automatically.
Stop recording
e To stop recording before
SAMP. STOP
recording finish
automatically with
3
memory full, push the
STOP (a CUE) button.
• The EXIT/RELOOP LED light to indicates
Sampler Loop mode is set automatically.
20
i, !0 q, r, !0 w, o y, u
Play Sampler sound
r Playback of the Sampler
sound starts when the
SAMP button is pushed after
recording has stopped.
• Sampler playback continues in looping.
With setting B point, playback loop
between A and B point. Without B point
4
setting Sampler loops whole recorded
length (about 15 seconds).
NOTE: It is not possible to play Sampler1
and Sampler2 at the same time.
t To stop the Sampler
sound push STOP (a CUE)
button.
Select Sampler Loop mode
You can select loop mode for Sampler when
Sampler playback stop.
Loop (default):
Sampler playback continues with
looping.
(EXIT/RELOOP LED stays lit)
Exit: Sampler playback continues over B
5
point up to recording length.
(EXIT/RELOOP LED flashes)
Single: Sampler playback stops at B point.
(EXIT/RELOOP LED turned off)
y To select loop mode, push
EXIT/RELOOP button after
recording and before playing.
Exit and Reloop
u The EXIT/RELOOP button
6
can be used same as
Seamless Loop function.
Reverse Play
i You can play Sampler sound in
reverse with push RVS (FLIP)
7 button. In reverse play mode
RVS LED lights up.
• Reverse playback will start with next
playback starting after reverse mode
e, t
turned on.
Moving Sampler B point
o When the B button is
pushed during Sampler
8
playback, the B point moves
to the point at which the
button was pushed, and loop
playback from point A starts.
Setting the Sampler volume and pitch
• The sound level (volume) and pitch can be
9
set individually for Sampler1 and 2.
• See m - step 8 "Adjust sound level and
pitch".
Clearing the Sampler data
!0 While pressing the (RVS)/FLIP/(CLR)
button, push the SAMP button (SAMP1 or
SAMP2) to clear the Sampler.
SAMP. STOP
10
• By pushing the (RVS)/FLIP/(CLR) button
for approx. 1 sec, you can clear both
Samplers 1 and 2.
# # # #
Hot start mode
Like with buttons A1 and A2, operation is performed
using the (RVS)/FLIP/(CLR), A3, A4 and EXIT/RELOOP
buttons. Operation is same as Hot Start with A1, A2
buttons. See page 16 for details.
Alpha-Track Hot Start mode
Like with buttons A1 and A2, operation is performed
using the (RVS)/FLIP/(CLR), A3, A4 and EXIT/RELOOP
buttons. (Refer to page 16.)