Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ICT ICT-IPS-LDM-LDM
Summarization of Contents
SAFETY GUIDELINES
Principles of Safe Operation and Maintenance
Emphasizes safety for personnel during installation, operation, and maintenance.
Visual Communication
Explains the meaning of safety symbols used in the manual.
General Alerts
Risk of Personal Injury or Damage
Provides critical safety warnings for installation and operation to prevent hazards.
Product Alerts
Specific Product Warnings
Highlights specific warnings related to product operation and potential risks.
GENERAL INFORMATION
Disclaimer
States ICT's liability limitations regarding product misuse or improper installation.
ICT LIMITED WARRANTY
Warranty Terms and Conditions
Details the warranty period, coverage, and conditions for ICT products.
INTRODUCTION
System Components and Features
Introduces the Modular Power Series, its architecture, and key modules.
INSTALLATION
Quick Install Guide
Provides a step-by-step overview of the installation process.
Installation Procedures
Unpacking and Inspection
Guides users on checking the unit for shipping damage and verifying contents.
Rack Mounting and Ground Connection
Rack Mounting
Instructions for physically mounting the unit in a standard 19-inch equipment rack.
Ground Connection
Explains the proper procedure for connecting the unit's ground bonding wire.
Module Installation
Installation of Power Module
Explains how to install hot-swappable power modules into the shelf.
AC Power and Energization
AC Power Source Connections
Details how to connect the unit to the AC power source.
Energize Loads and Battery Connections
Steps for safely energizing the system and its connected loads and batteries.
FRONT DISPLAY PANEL OPERATION
Graphic Display
Explains how to use the ICM's front display and buttons for monitoring and adjustments.
System Status
System Status Overview
Shows current operating conditions like input voltage, output voltage, and total current.
System Settings
Allows adjustment of system voltage, current limit, and other operational parameters.
Battery Management Module Operation
BMM Settings (All Battery Types)
Configures BMM settings like battery type, capacity, charge current, and LVD thresholds.
Discharge Test Configuration
Equalize Voltage Settings
Sets the recommended voltage for equalize charging of lead-acid batteries.
Discharge Test Configuration
Configures parameters for testing battery capacity via discharge.
Load Distribution Module Operation
LDM Settings
Allows adjustment of LDM settings, including output control and alarms.
Alarm History and Network Status
Alarm History
Shows a log of recent alarm events from modules and external inputs.
Password Reset and Status Indicators
Password Reset
Guides on how to clear a lost LCD password and reset GUI password.
Status Indicators and Alarms
Explains how unit status is indicated via LEDs, front panel, and network GUI.
GRAPHICAL USER INTERFACE ACCESS
Log In/Log Out
Instructions for accessing the web GUI and logging in/out.
GUI STATUS
DC Output Status
Shows the status of the DC output, whether it's Enabled or Disabled.
System Alarms
Shows the status of Form C alarms and installed power modules.
GUI SETTINGS & CONTROL - System
System Output Settings
Allows adjustment of system output voltage and current limit.
GUI SETTINGS & CONTROL - Power Modules
Power Modules Status
Provides status of installed power modules, including their operational status.
Battery Management Settings
Battery Management Settings
Configures BMM settings such as battery type, capacity, and charge parameters.
Battery Configuration
Configure Battery
Sets battery type, capacity, and discharge rate for system estimation.
Battery Charge and Equalize Settings
Battery Charge Current Limit
Sets the maximum charge current provided by the unit.
Equalize Charge Settings
Configures manual or automatic equalize charge cycles for lead-acid batteries.
LVD and Over-Current Settings
LVD Settings
Configures low voltage disconnect thresholds to protect batteries from over-discharge.
Battery Over-Current Alarm
Sets the threshold for receiving an alarm when battery current exceeds limits.
LDM Control and Settings
LDM Control
Enables control of individual LDM outputs, including on/off states.
LDM Output Configuration
Master Output Control
Turns all four LDM output channels on or off simultaneously.
LDM Output Settings
Output Load-Shedding
Disables specified outputs when DC voltage drops below a preset threshold.
Output Over-Current and Under-Current Alarms
Output Over-Current Alarm
Sets the threshold for receiving an alarm when output current exceeds limits.
Alarms Overview
Alarms Status
Shows all active alarms and up to 32 historic alarms.
Communications Setup
Basic Setup Configuration
Sets unit name, date/time, watchdog timer, and data logging features.
Network Setup Configuration
Configures network settings like IP address, subnet mask, and DNS.
E-Mail Setup Configuration
Configures SMTP server details for automatic email notifications.
User Setup
User Setup Configuration
Sets up usernames, passwords, and access levels for unit users.
Maintenance Options
Restore Factory Default Settings
Restores all system settings to original factory defaults.
FAQs
Password Reset FAQ
Guides on how to reset the GUI and LCD passwords.
Email Notifications FAQ
Explains how to configure the unit to send email alarms.
Firmware Upgrade FAQ
Instructions for downloading and installing the latest firmware.
PRODUCT SPECIFICATIONS
Electrical Specifications
Lists key electrical parameters like input voltage, current, efficiency.
Physical Specifications
Details physical attributes like grounding, connectors, temperature, and humidity.
Mechanical Specifications
Provides dimensions and weight information for the unit.
GLOSSARY
Glossary of Terms
Defines technical terms and acronyms used throughout the manual.
Need help?
Do you have a question about the ICT-IPS-LDM-LDM and is the answer not in the manual?
Questions and answers