Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for AQUARK MR.SILENCE MS110
Summarization of Contents
Safety Precautions
Warning
Defines hazard signs and their importance for personal or third-party injury.
Attention
Lists safety instructions like ventilation, fire source avoidance, and professional repair.
Safety
Covers electrical safety, lightning protection, ventilation during repair, and refrigerant leak procedures.
About Your Heat Pump
Transportation
Instructions on how to transport the unit, emphasizing keeping it upright and not lifting by water union.
Accessories
Lists included accessories like water union and drainage kit, showing connection.
Features
Lists key technical features of the heat pump, such as compressor type, fan motor, and protection systems.
Operating Range
Details the ambient temperature range for operation and ideal conditions for efficiency.
Introduction of Different Modes
Explains the Boost and Silence modes and their respective strengths.
Technical Parameters
Presents detailed technical specifications, including model numbers, heating capacity, and COP.
Dimension
Provides overall dimensions and installation clearance requirements for the heat pump.
Installation Guidance
Installation Reminder
Stresses that only professional staff should install the heat pump for safety and unit integrity.
Location and Water Pipe Connection
Guides on selecting a well-ventilated location and connecting water pipes, including drainage.
Wiring
Covers essential wiring practices, including power supply compliance, earthing, and using professional technicians.
Electric Wiring Diagram
Shows the schematic for electrical connections, specifying voltage and frequency requirements.
References for Protecting Devices and Cable Specification
Provides specifications for circuit breakers, fuses, power cords, and signal cables based on model.
Operation Guidance
Key Function
Introduces the main controls and display elements of the heat pump's user interface.
Operation Instruction
Explains how to use the controller, including screen lock, power on/off, temperature setting, and mode selection.
Wi-Fi Connection
Details the process for connecting the heat pump to a Wi-Fi network for remote control via an app.
Defrosting
Describes automatic and manual defrosting procedures for the heat pump.
Running Status Checking
Explains how to check the operational status and various sensor readings using the controller.
Testing
Inspect Heat Pump Before Use
Lists pre-operation checks for the ventilating system, piping, wiring, and power switch.
Leakage Detection Notice and Method
Provides guidelines and precautions for detecting refrigerant leaks, including prohibited methods.
Trial Operation
Outlines the correct procedure for starting and testing the heat pump, including pump and machine start/stop order.
Maintenance
Winter Season Preparation
Instructions for preparing the heat pump for winter shutdown, including power cutoff and draining.
Troubleshooting Common Faults
Repairing Guidance
General advice on troubleshooting, emphasizing professional service, safety, and refrigerant handling.
Failure Solution and Code
Lists common failures, their reasons, solutions, and protection/failure codes displayed by the unit.
Water Pump Control Connection
230V Voltage, ≤500W Capacity
Wiring diagram and specifications for connecting a low-capacity water pump to the heat pump system.
230V Voltage, >500W Capacity
Wiring diagram and specifications for connecting a higher-capacity water pump with a contactor.
400V Voltage
Wiring diagram and specifications for connecting a 400V water pump, including a contactor.
Water Pump Timer and Wiring
Explains how to connect the water pump wiring parallel to the timer for operation.
Wi-Fi Operation
InverGo Download
Instructions on downloading the InverGo app for smartphone control.
Account Registration
Guides on registering an account via email or third-party applications.
Email Registration
Step-by-step process for registering an account using an email address and verification code.
Register Through Third-Party Application
Instructions for registering using Facebook or Google accounts for convenience.
Create Family
Steps to set up a family name and location for device management within the app.
APP Pairing
Details the process of pairing the heat pump with the app via Bluetooth connection.
Wi-Fi Pairing
Explains how to connect the heat pump to the app using a Wi-Fi network.
App Operation
Illustrates the app interface for controlling heating-only and heating/cooling models.
Share Devices to Family Members
Instructions for sharing device control with other family members through the InverGo app.
Need help?
Do you have a question about the MR.SILENCE MS110 and is the answer not in the manual?
Questions and answers