Advertisement
Quick Links
Advertisement
Related Manuals for Victron Quattro 48/8000/
Summarization of Contents
Victron & REVOV Integration
1. Product & System Compatibility
Lists REVOV battery models and their specifications.
1.1 System Application Types
Outlines possible system types like Off-grid, Grid Backup, and ESS.
1.2 GX Device Requirement
Explains the necessity of a GX device for CAN-bus communication.
1.3 Inverter Compatibility
Details compatibility with Victron VE.Bus inverters and inverter/chargers.
1.4 MPPT Charger Compatibility
Discusses compatibility of Victron MPPT chargers with VE.Direct or VE.Can ports.
1.5 VE.Direct MPPT Integration
Explains how MPPTs with a VE.Direct port are controlled via the GX device.
1.6 VE.Can MPPT Integration
Details compatibility and requirements for VE.Can port MPPTs.
2. Minimum Battery Sizing
Provides recommendations for minimum battery sizing for Victron inverters.
3. CAN-bus Wiring
Illustrates CAN-bus wiring diagrams for connecting Victron and REVOV systems.
3. CAN-bus Wiring - Port Purpose
Explains the purpose of CAN and RS485 ports for battery communication.
DIP Switch Assignment
Provides dip switch assignments for master and slave battery units.
GX Device Connection Cable
Details connecting the Master battery to the GX device using a specific cable.
4. VE.Configure Settings
4.1 General Tab Settings
Explains settings in the General tab of Victron's VE.Configure software.
4.1 General Tab - Parameters
Details specific parameters like system frequency, shore limits, and battery monitor.
4.2 Grid Code Tab
Covers grid code selection and Loss Off Mains (LOM) detection settings.
4.2 Grid Code Tab - Local Standards
Emphasizes selecting the appropriate country/grid code for safe operation.
4.3 Inverter Settings Tab
Details inverter settings such as output voltage and DC input shut-down levels.
4.3 Inverter Settings Tab - Power Assist & SOC
Covers settings like Power Assist and shut-down on SOC.
4.4 Charger Tab Settings
Explains charger settings like battery type, charge curve, and absorption voltage.
4.4 Charger Tab - Charge Parameters
Details charge current, float voltage, and absorption time settings.
4.5 Virtual Switch Tab
Describes the configuration of virtual switch usage for relays and inputs.
4.5 Virtual Switch Tab - Usage Options
Details the usage options for virtual switches.
4.6 Assistant Tab - ESS Setup
Guides on adding assistants, specifically ESS (Energy Storage System).
4.6 Assistant Tab - Battery System Type
Instructs to select the battery system type within the ESS assistant.
ESS Assistant - Battery Capacity Input
Details how to enter the correct battery capacity within the ESS assistant.
ESS Assistant - Battery Type Selection
Explains selecting "Do not change battery type" for the VEConfigure assistant.
ESS Assistant - Sustain Voltage
Details the sustain voltage setting to prevent battery damage during deep discharge.
ESS Assistant - Dynamic Cut-off
Explains the dynamic cut-off setting for low voltage protection based on discharge current.
ESS Assistant - Restart Offset
Describes the restart offset setting for allowing inverting after low battery conditions.
ESS Assistant - PV Inverters
Addresses whether PV inverters are connected to the Multi/Quattro system.
ESS System Settings Overview
Refers to ESS QuickStart and Design Manuals for grid-connected ESS.
Hardware Protection Points
Voltage and Temperature Limits
Details low and high voltage protection triggers and operating temperature ranges.
Current and Short Circuit Limits
Specifies current limits and short circuit protection for safety.
5. GX Device Settings
GX Device Port Connection
Explains connecting the battery to the GX device's BMS-Can or VE.Can ports.
DVCC Configuration
DVCC Settings Overview
Outlines DVCC settings like shared voltage, temperature, and current sense.
DVCC Voltage & Current Limits
Explains setting managed battery charge voltage and current limits in DVCC.
6. VE.Direct MPPT Settings
MPPT Precautionary Settings
Lists precautionary settings for MPPT battery voltage, absorption, and float voltage.
7. Troubleshooting
System Power On Issues
Steps to take if the inverter/charger or GX device does not switch on.
Battery Visibility on GX Device
Checks to perform if the REVOV battery is not visible on the GX device.
Checking Battery Readiness
How to check if the REVOV battery is ready for use via GX device parameters.
REVOV Manual for Diagnostics
Refers to the REVOV manual for detailed troubleshooting and LEDs.
8. FAQ and Known Issues
Current Limit Explanation
Explains the difference between datasheet current limits and system restrictions.
Charge Current Fluctuation Cause
Explains why charge current may fluctuate between 0A and 80A.
Cold Weather Charging Limits
Discusses charging limitations in cold weather and how to check CCL/DCL.
Battery Not Reaching 100% Charge
Explains why the battery may not show 100% charge and how to resolve it.
High Voltage Alarm Resolution
Addresses 'high voltage' warnings and methods to help batteries balance.
Need help?
Do you have a question about the Quattro 48/8000/ and is the answer not in the manual?
Questions and answers