Related Manuals for Pneu-Dart 389
Summary of Contents for Pneu-Dart 389
- Page 1 OPERATING Model 193 Model 196 INSTRUCTIONS Model 389 CARTRIDGE FIRED PROJECTORS w w w . p n e u d a r t . c o m pneudart...
- Page 2 NOTICE: Model 389 & Model 196: Savage does not provide after-market assistance with lost or broken bolts and as a result, these items are not able to be replaced or repaired. 2 | PNEU-DART...
- Page 3 Here’s how: Pneu-Dart sells a cleaning kit of this application. When faced with 1. OPEN THE BOLT AND ACTION; rusty or neglected barrel, use a wire...
- Page 4 Cleaning the front rotated freely. chamber for model 193 can Please follow instruc- 5. M 182 - be accomplished by removing oDEl tions as listed for model 171C.
- Page 5 page 10). Extract the power to both areas and place the control rod and coupler from power control back into the within the receiver tube and gas block. Remove the knock- affix the Pneu Dart provided out disk from the end of the knockout disk to the end of coupler, apply a light coat of coupler (see Figure F , page 11).
- Page 6 PNEU-DART MODEL 196 CARTRIDGE FIRED RIFLE S P E C I F I C A T I O N S 196, 196 , 196 , 196 – .22 cal. Power Charges toCk anD artriDgEs – S II Fv .22 – Open Rear – Fiber optic front...
- Page 7 To insure impact is as light as represents the least amount of possible, experience with practice pressure for close range shoot- is recommended. Pneu-Dart sells ing conditions. Desired setting weight equivalent practice darts and should be positioned at the top targets.
- Page 8 PNEU-DART MODEL 389 CARTRIDGE FIRED RIFLE S P E C I F I C A T I O N S , 389 , 389 – .22 cal. Power Loads toCk anD Ction artriDgEs – Savage Mark II FV .22 caliber 5 shot –...
- Page 9 4 (see Figure C, this page). Locate the setscrew access just behind the gas block (see Figure D, page 10) and remove the small setscrew using the Pneu-Dart provided 3/32" allen wrench. With a flathead screwdriver remove the example; number one represents...
- Page 10 #4 hole in the gas control valve + hole in the gas block. Lastly, screw in the power control retention screw previously removed. Figure E 10 | PNEU-DART...
- Page 11 Figure F coupler Figure G Figure G1 Above: Be sure of alignment of Number "4" hole in the gas control valve and gas block, as referred to on page 9. : Do not leave dart in aution projector for an extended period Above: A close-up view of the of time as drug may leak out and 389's air control ports.
- Page 12 PNEU-DART MODEL 193 CARTRIDGE FIRED RIFLE S P E C I F I C A T I O N S 193, 193 , 193 , 193 – .22 cal. Power Charges artriDgEs toCk anD – Marlin Model XT .22 cal. 5 –...
- Page 13 Recommended CCI charges To insure impact is as light as are Brown, Green and Yellow. possible, experience with prac- Please refer to the “Power tice is recommended. Pneu-Dart Control Chart” for charge and sells weight equivalent practice setting recommendations. darts and targets.
- Page 14 HOW TO ADJUST TRIGGER PULL : The XT based bolt action rimfire projector should not be disas- aution sembled beyond what is described in this manual, except by Pneu-Dart, Inc. or an authorized Pneu-Dart repair center. Warning! Unload the projector before disassembly. Look into the ejection port and visually check the chamber and magazine to make sure there are no cartridges or darts in the projector.
- Page 15 TO ADJUST TRIGGER PULL: 1. Loosen the 3/8" retaining nut by turning it counterclockwise. Do not remove. (see Figure J, this page) 2. Insert a 3/32" hex key wrench into the trigger adjustment hole. (see Figure K, this page) 3. To increase trigger pull weight, turn the hex key clockwise.
- Page 16 PNEU-DART'S GUIDE TO GENERAL SAFETY 1. Handle every projector as if it 12. Be sure to keep the barrel and was loaded. mechanism free of obstruc- tions. 2. Keep the safety on SAFE until you are ready to shoot. 13. Before cleaning, be sure the chamber, action and magazine 3.
- Page 17 Safety Warning: Pneu-Dart strongly recommends that you take a safety course, taught by a certified instructor, before you use this projector. Contact Pneu-Dart for further details.
-
Page 18: Repair Service
International customers should contact their respective distributor. Your projector requires special tools and fixtures to repair it. If you take it apart, you probably will not be able to reassemble it correctly. Pneu-Dart assumes no warranty responsibility under such circumstances. -
Page 19: Field Notes
FIELD NOTES... - Page 20 Pneu-Dart, Inc. 15223 Route 87 Highway Williamsport, PA 17701 Toll Free: 866.299.DART (3278) Phone: (570) 323-2710 Fax: (570) 323-2712 E-mail: info@pneudart.com w w w . p n e u d a r t . c o m pneudart...
Need help?
Do you have a question about the 389 and is the answer not in the manual?
Questions and answers